NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 118  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Brokerage-Hot Line-CCIS
BROKERAGE-HOT LINE-CCIS
General Description
This feature provides a ringdown connection between two stations, each using a Dterm, in
different offices in the CCIS network.
Programming
DESCRIPTION DATA
Assign the Virtual Line station number to 
the required Virtual LEN.(1)
(2)000-255: Virtual LEN
X-XXXXXXXX: Virtual Line station No.
Assign the Hot Line to the Virtual Line sta-
tions assigned by CM11.
(1)
(2)YY=03
X-XXXXXXXX: Virtual Line station No.
04: Hot Line
Allocate the memory area for the Hot Line-
Outside call. 
For example, to assign the 10 Hot Line-
Outside calls into No. 100 through No. 109 
Memory Slots, 2nd data is “100010”. Ab-
breviated Codes are automatically as-
signed as shown below:(1)
(2)65: For Hot Line-Outside
XXX YYY
XXX: 000-299 (Starting Memory Slot 
No. in blocks)
YYY: 001-300 (No. of Memory Slots to 
be assigned in blocks)
Assign the destination party’s number and 
name to each Memory Slot number.
(1)
(2)Y=0
000-299: Memory Slot No.
XXXX  YY...Y
XX     : Access Code (Max. 2 digits)
: Separator Mark
YY...Y : Calling Par ty’s No. 
(Max. 26 digits)

(1)
(2)Y=1
000-299: Memory Slot No.
XXX...X: Station Name Character Code 
(Max. 32 digits: 16 characters)
See CM77 in the Command Manual.
CM12
CM71
CM72 START
CM11
Memory Slot 100
Memory Slot 109~Abbrev. Codes
00
09
~
,
,
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Brokerage-Hot Line-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 119
Operating Procedure
To access from a Dterm:
(1) Lift the handset or press the SPEAKER key.
(2) Press the line/feature key associated with the preassigned station. 
The destination station is automatically dialed; ring back tone is heard, destination station 
answers.
(3) After completion of conversation, hang up or press the SPEAKER key.
To make another Brokerage-Hot Line-CCIS call immediately, press another line/feature key
without going on hook and off hook.
DESCRIPTION DATA

(1)
(2)Y=2
000-299: Memory Slot No.
XXX...X: Station Name Character by 
MAT/CAT (Max. 16 characters)
Assign the Hot Line pairs.
Bidirectional Hot Line should be assigned 
as follows: 
 Hot Line 
 Pair No. 
 Calling Side Called Side
  00  Station A  Station B
  01  Station B  Station A
NOTE 1:Up to 100 Hot Line stations (50 
pair) can be set.
(1)
(2)YY=00-99 Hot Line pair No.
0: Calling Station
1: Called Station 
Station No.
E00X
X: 0-7: ATTCON No. assigned by CM06 
Y=01
CXX (For Called Outside party)
XX: Abbreviated Code given by CM71
NOTE 2:Do not assign station number 
with first digit “0”.
Assign the Virtual Line station and 
RELEASE keys on the D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
X-XXXXXXXX: Virtual Line station No.
F1020: Release key
END
CM72
A
CM90
CM52
, 
						

							 NEAX2000 IVS2 CCIS System ManualPage 120  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Busy Verification-CCIS
BUSY VERIFICATION-CCIS
General Description
This service feature permits the operator, via the Attendant Console on the IMX or the IVS, to
interrupt a busy station’s call at another switching office connected through CCIS.
Programming
DESCRIPTION DATA
Provide the system with Busy Verification. (1)
(2)012
1 : Available
Specify whether the Warning Tone is sent 
to the connected parties.
 Three burst tone 
[Australia/Other Countries]
 One burst tone 
[New Zealand Only](1)
(2)046
0 : Not sent
1 : To send
Specify the Warning Tone sent to connect-
ed parties.(1)
(2)045
0 : Only once
1 : Every 4 sec.
Specify the Warning Tone sent to the 
outside party.(1)
(2)076
0 : Not sent
1 : To send
Assign Service Restriction Class A to the 
required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Busy Verification in the Service 
Restriction Class A assigned by CM12 
YY=02.
(1)YY=09
00-15 : Service Restriction Class A 
assigned by CM12 YY=02
1: Allow
CM12
CM15 START
END
CM08 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Busy Verification-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 121
Operating Procedure
To activate Busy Verification-CCIS:
(1) Press an idle LOOP key.
(2) Dial the desired station number; receive busy tone.
(3) Press the BV key.
(4) Two-burst tones are sent to connected parties.
(5) The operator may monitor or join the conversation.
(6) Press the RELEASE key to disengage. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 122  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Back-CCIS
CALL BACK-CCIS
General Description
This feature provides inter-office Call Back-CCIS service. A station user who has dialed a busy
station at another office can set Call Back-CCIS by dialing a feature access code. When this
service has been set, the calling station will be rung as soon as the busy station becomes
available.
Programming
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Call Back in the Service Restriction 
Class A assigned by CM12 YY=02.
(1)
(2)YY=03
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Assign the access code for Call Back.
(1)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
For setting the different access code from 
OG Trunk Queuing:
(2) A002: Call Back Set
A003: Call Back Cancel
For setting the same access code as OG 
Trunk Queuing:
(2) A004: Set
A005: Cancel
Assign a Call Back key to the D
term, if 
desired.
(1)
(2)YY=00
My Line No. +   + Key No. 
F0004: Trunk Queuing-Outgoing/Call 
Back
CM15
CM20
CM90 START
END
CM12
, 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Back-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 123
Operating Procedure
Single-Line Telephone:
To set Call Back-CCIS from a Single-Line Telephone:
(1) Dial desired station number; receive busy tone.
(2) Press hookswitch for feature dial tone.
(3) Dial Call Back-CCIS feature access code; receive service set tone.
(4) Replace the handset.
(5) When desired station becomes idle, calling station will ring.
(6) When calling station answers, called station will be rung.
To cancel Call Back-CCIS from a Single-Line Telephone:
(1) Lift handset; receive dial tone.
(2) Dial Call Back-CCIS cancellation code; receive service set tone.
D
term:
To set Call Back-CCIS from a D
term:
(1) Dial desired station number; receive busy tone.
(2) Press the CALL BACK Line/Feature key, receive service set tone. LCD displays:
(3) Replace the handset.
(4) When called station becomes idle, calling station will ring. The LCD displays:
SET            XXXX
(TIME DISPLAY)
Called station number D
term 65 Series Dterm 75 Series
SET            XXXX
(TIME DISPLAY)
CB            XXXX
(TIME DISPLAY)
Called station number 
flashes at calling station D
term 65 Series Dterm 75 Series
CALL BACK            XXXX
(TIME DISPLAY) 
						

							 NEAX2000 IVS2 CCIS System ManualPage 124  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Back-CCIS
(5) When calling station answers, the called station will ring.
(6) The originaly called Station’s LCD displays:
To  c a n c e l
 Call Back-CCIS from a Dterm:
(1) Lift the handset or press the SPEAKER key, receive dial tone.
(2) Press the Call Back Line/Feature key; receive service set tone. Call Back-CCIS is canceled
(3) The LCD displays:
XXXX
(TIME DISPLAY)
Called station number D
term 65 Series Dterm 75 Series
XXXX
(TIME DISPLAY)
CB CNCL         XXXX
(TIME DISPLAY)
Dterm 65 Series Dterm 75 Series
CANCEL         XXXX
(TIME DISPLAY) 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-All Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 125
CALL FORWARDING-ALL CALLS-CCIS
General Description
This service feature permits all calls destined for a particular station to be routed to another
station, or to an Attendant Console, in another office in the CCIS network regardless of the status
(busy or idle) of the called station. Activation and cancellation may be accomplished by either the
station user or an Attendant.
Programming
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations. 
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Call Forwarding-All Calls and Call 
Forwarding-All Calls-Outside in the 
Service Restriction Class A assigned by 
CM12 YY=02.
NOTE:When providing Call Forwarding-
All Calls-Outside, set “1” (Allow) 
for YY=00, YY=26 of CM15.

(1)
(2)YY=00 Call Forwarding-All Calls
YY=26 Call Forwarding-All Calls-
Outside
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Assign an access code for Call 
Forwarding-All Calls Entry and Cancel 
respectively.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
A010: Call Forwarding-All Calls Entry
A011: Call Forwarding-All Calls Cancel
To apply this feature to incoming calls, 
assign trunk route combinations for 
Tandem connection.
(1)
(2)YY=05
00-63: Trunk Route No.
1 : Release Signal arrive

(1)
(2)Y=0
Incoming Trunk Route No. + Outgoing 
Trunk Route No. for CCIS (Assigned by 
CM35 YY=05)
0: Allow
CM15
CM36 START
CM12
A
CM35
CM20 
						

							 NEAX2000 IVS2 CCIS System ManualPage 126  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-All Calls-CCIS
DESCRIPTION DATA
Specify the Call Forwarding-All Calls-Out-
side setting operation.(1)
(2)222
0 : The feature is set when the station 
goes on hook/when receiving 
Service Set Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Assign whether or not an extension can 
set Call Forwarding-All Calls-Outside by 
entering only a trunk access code.(1)
(2)386
0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the for-
warded station during a Call Forwarding-
All Calls-Outside.(1)
(2)387
0 : Call forwarding All Calls-Outside 
follows setting station class
1 : No check
Provide Call Forwarding feature with each 
tenant as per incoming call type.


(1)
(2)YY=23
Internal Call or ATT assisted Call
YY=24 C.O. Incoming Call
YY=25 Tie Line Incoming Call
00-63: Tenant No. 
1 : Call Forwarding
Select the Dial Tone on setting Call For-
warding-All Calls.
(1)
(2)Y=2
13: Dial Tone on Setting Call Forward-
ing-All Calls
0 : Special Dial Tone
1 : Dial Tone
Assign a Call Forwarding-All Calls key to 
the D
term, if desired.
(1)
(2)YY=00
My Line No. +   + Key No.
F0010: Call Forwarding-All Calls Set/
Cancel
END
CM08
A
CM90
CM48
CM65
INITIAL
, 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-All Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 127
When a call is forwarded through CCIS by Call Forwarding-All Calls/-Busy Line/-Don’t Answer,
the kind of Call Forwarding and the station number which is setting the service can be indicated
on the LCD of the forwarding destination D
term.
To provide this feature, perform the following programming.
On the Forwarding side PBX (PBX-A)
On the Forwarded destination side PBX (PBX-B)
DESCRIPTION DATA
Provide the system with sending of Call 
Forwarding station information through 
CCIS.(1)
(2)373
0: To provide
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Specify the LCD digits number of the D
term 
as 24 digits.
(1)
(2)YY=95
00-15: Service Restriction Class A 
assigned by CM12 YY=02
0: 24 digits
PBX-APBX-B
STATION
/TRUNKCCIS
STATION 2000Kind of Call Forwarding
Call Forwarding-All Calls/
Busy Line/Don’t Answer. Call is forwarded from
Station 2000 byand station number “2000”
are indicated on LCD.
START
END
CM08
START
END
CM12
CM15