NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 148  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Transfer-Attendant-CCIS
NOTE 1:In the Inter-Tenant Connection Assignment, the Tenant number should be assigned as
01-63. 00 should not be used if connecting to a PBX.
NOTE 2:Refer to Numbering Plan Assignment and assign a dial code to call the attendant by
the LCR feature.
Operating Procedure
To transfer a call to an Attendant Console:
(1) While engaged in a Central Office trunk call, switch hook flash; receive feature dial tone.
(2) Dial the Operator Access Code.
(3) The ATND lamp on the Attendant Console flashes and the buzzer sounds. The station 
receives ringback tone.
To answer from the Attendant Console:
(1) Refer to the “IMX Attendant Console User Guide”.
If the station wishes to return to the Central Office trunk call while the Attendant Console is being
called:
(1) Switch hook flash. the ATND lamp is extinguished at the Attendant Console and the buzzer 
stops.
(2) Ringback tone ceases; the station returns to the Central Office trunk call. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Calling Name Display-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 149
CALLING NAME DISPLAY-CCIS
General Description
This feature provides a display indicating the calling/called par ty’s name, at another switching
office, on the LCD of a D
term or an Attendant Console.
Programming
DESCRIPTION DATA
Provide the system with the Name Display 
service.(1)
(2)255: Name Display
1 : To provide
Specify the number of digits sent to the 
CCIS network to 24 digits.(1)
(2)379: Number of dialed digits
0: 24 digits
Specify the time to go back to date and 
time display after the call is answered.(1)
(2)120
0 : 10 sec. later
1 : 6 sec. later
Specify the duration to display the name. (1)
(2)121
0 : Until call finished
1 : As per CM08>120
Assign the access code for station user 
name entry from an individual station.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code (0-9, *, #)
A110
Assign a trunk name number to each trunk 
route.
(1)
(2)YY=03
00-63: Trunk Route No.
00-14 : Trunk Name No.
15 : Kind of trunk route assigned by 
CM35 YY=00 are displayed
16-63 : Trunk Name No.
Provide each CCH number with Name 
Display feature.
(1)
(2)YY=26 Name Display
0-7: CCH No. 0-7
0: To provide
CM20 START
CM08
CM35
A
CMA7 
						

							 NEAX2000 IVS2 CCIS System ManualPage 150  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Calling Name Display-CCIS
NOTE 1:The maximum number of stations that can be provided with user’s name display is 384.
The maximum number of characters per name is eight, including spaces.
NOTE 2:User’s name can be assigned to Single Line Telephones, and cannot be assigned to
the Attendant Console.
NOTE 3:The trunk name display is provided on a trunk route basis. The maximum amount of
characters in the trunk name display is four. And the maximum number of trunk routes
assignable is 16.
NOTE 4:A name currently programmed can be changed by overwriting with a new name, or by
inserting a blank space as the first character. This will cancel the existing name.
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Enter the desired user’s name to each sta-
tion number with Character Codes or char-
acters.
(1)
(2)Y=0 By Character Code
X-XXXXXXXX: Station No.
20-7F: Character Code
Max. 32 digits
(See CM77 in the Command Manual)

(1)
(2)Y=1 By character
X-XXXXXXXX: Station No.
A-Z, 0-9: Character
Max. 16 characters
Assign the desired trunk name to each 
trunk route by Y=2 or Y=3.
(1)
(2)Y=2 By character Code
00-14, 16-63: Trunk Name No. 
assigned by CM35 YY=03.
Character Code 20-7F:
(See CM77 in the Command Manual)

(1)
(2)Y=3 By character
00-14, 16-63: Trunk Name No. 
assigned by CM35 YY=03.
A-Z, 0-9: Character Code
Max. 4 characters
END
CM77
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Calling Number Display-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 151
CALLING NUMBER DISPLAY-CCIS
General Description
This feature provides a display indicating the calling/called p arty’s number, at another switching
office via the CCIS network, on the LCD of a D
term or an Attendant Console/Smar t Console.
To transfer the calling par ty number received from the network (ISDN CPN/Caller-ID/MFC or T1-
ANI) transparently between the offices on the CCIS network, assign the following data.
The calling party number sent from the network over CCIS can be display on the LCD of the
station of another office over CCIS, and can be sent to the SMDR. It can be sent to also the MCI,
if the system provides the MCI with ANI.
Programming
DESCRIPTION DATA
Provide the system with the Name Display 
service.(1)
(2)255
1 : To provide
Office AOffice B
ISDN CPN/ 
Caller-ID/ 
MFC-ANI/ 
T1-ANICalling Party NumberCCIS 
TransparentDisplay of 
Calling Party 
Number on LCD
Sending of 
Calling Par ty 
Number to 
MCI/SMDR
START
CM08
A 
						

							 NEAX2000 IVS2 CCIS System ManualPage 152  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Calling Number Display-CCIS
The conditions for transferring calling party number over CCIS related to the Call Transfer, Call
Forwarding feature are described below.
When the Station 300 on the Office B answers the call from the network, and transfers the call to
the Station 301 on the Office B, the calling party number will be displayed on the Station 301.
When the Station 200 on the Office A answers the call from the network, and transfers the call to
the Station 300 on the Office B, the calling party number will not be displayed on the Station 300.
DESCRIPTION DATA
Specify the number of digits sent to the 
CCIS network as 24 digits.(1)
(2)379
0: 24 digits
Provide each CCH channel with Name 
Display feature.
(1)
(2)YY=26
0-7: CCH Channel No. 0-7
0: To provide
Provide each CCH channel with the 
information transferring service.
(1)
(2)YY=28
0-7: CCH Channel No. 0-7
0: To provide
CMA7
END
CM08
A
ISDN CPN/ 
Caller-ID/ 
MFC-ANI/ 
T1-ANIOffice A
Office B
Calling Par ty NumberCCIS
Call Transfer300301
The calling p a rty number can be displayed.
ISDN CPN/ 
Caller-ID/ 
MFC-ANI/ 
T1-ANIOffice A
Office B
Calling Par ty Number
CCIS
300200
The calling party number can not be displayed.
Transfer 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Calling Number Display-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 153
When the call from the network terminates to the Station 300 on the Office B and be forwarded
to the Station 301 on the Office B, the calling party number will be displayed on the Station 301. 
When the call from the network terminates to the Station 200 on the Office A and be forwarded
to the Station 300 on Office B, the calling par ty number will be displayed on the Station 300.
Operating Procedure
No manual operation is required. 
ISDN CPN/ 
Caller-ID/ 
MFC-ANI/ 
T1-ANI Office A
Office B
Calling Party NumberCCIS
Call Forwarding 300301
The calling party number can be displayed.
ISDN CPN/ 
Caller-ID/ 
MFC-ANI/ 
T1-ANIOffice A
Office B
Calling Party Number
CCIS
300200
The calling party number can be displayed.
Call Forwarding  
						

							 NEAX2000 IVS2 CCIS System ManualPage 154  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Billing-CCIS
CENTRALIZED BILLING-CCIS
General Description
This feature is used to collect billing information from each office within the network and to direct
it to the associated center office. Billing information is then forwarded to the SMDR of center
office.
Programming
Programming Summary
NOTE:AP00 is required in Local Office/Tandem Office.
NOTE NOTE
DTI LOCAL 
OFFICE
TANDEM 
OFFICE
CCH
DTI
CCH
DTI
CENTER 
OFFICE
CCH
DTI
CCH
AP00 MPAP00AP00 MP
SMDR 
TERMINAL MP
END START
AP INITIALIZATION
SMDR WITH AP00
PROGRAMMING (2)
 Page 155
Page 158
 Page 155
AP00
 Page 162
 Page 164
MP CENTER OFFICE
AP INITIALIZATION
SMDR WITH AP00
PROGRAMMING (1)Local OFFICE/ 
Tandem OFFICE
LOCAL OFFICE
TANDEM OFFICE OR
CENTER OFFICE?MP (BUILT-IN SMDR)
OR AP00?
BUILT-IN SMDR
PROGRAMMING 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Billing-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 155
AP Initialization
This section explains the data assignment to make the AP active. If the system already applied
the AP related feature, you can skip the data assignment explained in this section. The AP should
have already been activated if one of the following feature is applied: Station Message Detail
Recording (SMDR), Message Center Interface (MCI), D
term Time Information Management
System (TIMS), Proper ty Management System (PMS), or Hotel printer. You can distinguish
whether the AP is active by the RUN lamp indication. The RUN lamp flashes green when the AP
is in active mode.
When installing the AP00 at first time, do the following AP initialization.
DESCRIPTION DATA
Assign an AP number to the AP00 card.
The AP number must match the SENSE 
switch setting on the AP00 card.
(1)
(2)Y=0
04-15, 20-31: AP No.
04: AP00 card
On the AP00 card, set SW1 switch as 
shown below.
SW1-4 should be set as follows; 
ON : The AP No. is 04-15
OFF : The AP No. is 20-31
Load the initial data into the AP00 card. (1)
(2)0000
CCC
Specify Local Office or Center Office for 
Centralized Billing-CCIS(1)
(2)179
0 : Local Office
1 : Center OfficeSTART
CM05
CMD101
A
CMD001
INITIAL
SW1
ON
:   POSITION TO BE SET
4
3
2
1
AP OFF LINE 
						

							 NEAX2000 IVS2 CCIS System ManualPage 156  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Billing-CCIS
DESCRIPTION DATA
Allow the maximum number of Call Record 
for SMDR which is set to “5” by 
CMD001>80/100/120/140.
NOTE:When the data is set to 1-27000, 
external alarm of memory 
overflow is available, if CM44, 
2nd data=3002 is assigned.(1)
(2)24
0 : No limitation
1-27000 : 1-27000 calls
Assign the maximum number of Local of 
fice’s Call Record for Centralized Billing 
office.
NOTE:When the data is set to 1-27000, 
external alarm of memory 
overflow is available, if CM44, 
2nd data=3000 is assigned.(1)
(2)26
0 : No record
1-27000 : 1-27000 calls
Assign the maximum number of Call 
Record for SMDR/PMS which is set to “4” 
by CMD001>80/100/120/140.
NOTE:When the data is set to 1-27000, 
external alarm of memory 
overflow is available, if CM44, 
2nd data=3001 is assigned.(1)
(2)29
0 : No record
1-27000 : 1-27000 calls
CMD003
A
B 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Billing-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 157
 
DESCRIPTION DATA
Initialize the billing memory. (1)
(2)0000
CCC
On the AP00 card, set the SW1 switch as 
shown below: 
SW1-4 should be set as follows:
ON: The AP No. is 04-15
OFF: The AP No. is 20-31
NOTE 1:“DATA ERROR” will be indicated when CMD102>000: CCC is entered in case that 
the sum of all call records numbers set by second data of CMD003>23, 24, 25, 26, 
28, 29, 30 exceeds the amount of call records number shown in NOTE 3, or 
System Data All Clear by CMD101 is not executed.
NOTE 2:By entering the 1st data “0000”, status of the EXPMEM card (PZ-M537) will be 
displayed as shown below.
CMD102
B
END
AP OFFLINE
SW1
ON
:   POSITION TO BE SET
4
3
2
1
No EXPMEM on AP00 is Provided EXPMEM on AP00 is provided
When CMD001>179 is set 
to 0
(Not a center office of 
Centralized Billing-CCIS)When CMD001>179 is set 
to other than 0
(Center office of 
Centralized Billing-CCIS)When CMD003>28
is set to 0
(No Call Record for CIS is 
provided)When CMD003>28
is set to other than 0
(Call Record for CIS is 
provided)
1600 800 27000 26000