NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 178  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Billing-CCIS
Example 5: Data Assignment of CMD004>56
To specify the billing office (Office B) in center office (Office C) when a station of Office A make
an outgoing call through Office B:
Data Assignment of Office A
Command Code 1st Data 2nd Data Remarks
CMD004 56 822
OFFICE 
A
OFFICE 
BOFFICE 
C CCH0 Sta.
CCH0CCH1SMDR
PC: 00001 
OFFICE NO.: 821
PC: 00002 
OFFICE NO.: 822PC: 00003 
OFFICE NO.: 823 Billing Information 
of Office B
PC : Point Code
CCH: Common Channel Handler
PSTN 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Day/Night Mode Change-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 179
CENTRALIZED DAY/NIGHT MODE CHANGE-CCIS
General Description
This service feature switches the Day/Night Mode of a remote office, linked to the main office IMX
via CCIS, in accordance with the Day/Night Mode switching on the Attendant Console at the main
office.
For Satellite Office
If no Attendant Console is required in the Satellite Office, the following programming is 
required.
DESCRIPTION DATA
Assign as ineffective Trunk Restriction 
Class change by NT (Night) switch on 
ATTCON/DESKCON.
(1)
(2)YY=02
0-7: ATTCON No.
1 : Ineffective
Assign as ineffective outgoing call 
restriction on Night Mode by NT switch on 
ATTCON/DESKCON.
(1)
(2)YY=04
0-7: ATTCON No.
1 : Ineffective
Assign as ineffective Day/Night Mode 
Change by NT switch on ATTCON/
DESKCON.
(1)
(2)YY=06
0-7: ATTCON No.
1 : Ineffective
SATELLITE OFFICE MAIN OFFICE
AT T
CCIS
IMX
PBX
START
END
CM60
INITIAL
INITIAL
INITIAL 
						

							 NEAX2000 IVS2 CCIS System ManualPage 180  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized Day/Night Mode Change-CCIS
To provide an indication on external equipment when Day/Night Mode status is changed by the
Attendant Console at the Main Office, do the following programming.
Hardware Requirements
DK card × 1/External Equipment Interface on the MP card
External Indicator (Bell, Lamp etc.) provided by the customer
For cross connection of the External Indicator, refer to the Installation Procedure Manual.
Operating Procedure
Main Office:
(1) The Attendant executes Day/Night Mode changeover operation using the normal Attendant 
Consoles (no master) method or the master Attendant Console method.
(2) After a specified time, the Day/Night Mode at the remote office is changed over.
Remote Office:
No manual operation required.
DESCRIPTION DATA
Assign the DK card to the required LEN.
NOTE 1:The DK card number must be as-
signed to the 1st LEN (Level 0) 
and the 3rd LEN (Level 2) of 
each LT slot.(1)
(2)000-763: LEN
E800-E831: DK Card No.
For PIM0/PIM1: E800-E807
For PIM2/PIM3: E808-E815
For PIM4/PIM5: E816-E823
For PIM6/PIM7: E824-E831
NOTE 2:Circuit No. 3 of E831 is used 
for built-in External 
Equipment Interface of MP 
card by setting CM44.
Assign the function of CCIS Day/Night 
status Indication to the DK card.(1)
(2)XX Y: Circuit No.
XX : 00-31: DK Card No. assigned by 
CM10 E800-E831
Y : 0-3: Circuit No.
313 : Built-in External Equipment 
Interface on MP card
3601START
END
CM10
CM44 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized MAT-CCIS (Future Enhancement)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 181
CENTRALIZED MAT-CCIS (FUTURE ENHANCEMENT)
General Description
All nodes in the multiple IMXs and IVSs through CCIS link can be maintained from the sole MAT
installed in an IMX.
When the fault occurs at an IVS, the fault information (node name, alarm kind) is displayed on at
the Centralized MAT.
• The IVS must be a subordinate office.
 The opposite office must be an IMX.
A connection among IMX and two or more IVSs cannot provide the Centralized MAT feature.
 For the station number in integrated numbering plan through CCIS network, access code 
for network station number set by CM20>811-818 is required.
IMX
IMXIMX
IVS
Fault Information
Centralized MAT
IVS
Fault Information CCIS
CCIS Fusion Network
CCIS IMX
Cannot connect IVS IVS 
						

							 NEAX2000 IVS2 CCIS System ManualPage 182  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized MAT-CCIS (Future Enhancement)
Programming
DESCRIPTION DATA
Assign fault kind information and its 
external alarm kind.
Fault Kind number:
01 : System Initialization
04 : MP-FP/AP communication failure
08 : FP/AP card down
09 : Power failure
12 : CS/ZT fault occurred
16 : Battery exchange periodic alarm
20 : DTI Line failure
21 : DCH/BRT/PRT D-channel link 
connection failure
22 : CCH Link connection failure
24 : Number of faulty trunks was more 
than predetermined number.
25 : The number of lockout stations was 
more than predetermined number.
26 : DLC card down
27 : Synchronism of DPC missed
28 : SMDR output buffer memory overflow
2B : CS/ZT fault occurred.
18 : FP/AP card returned to normal 
condition.
19 : Power failure returned to normal 
condition.
30 : DTI Line returned to normal 
condition.
31 : DCH/BRT/PRT D-channel link 
connection returned to the normal 
condition.
32 : CCH Link connection returned to 
normal condition.
34 : Number of faulty trunks was less than 
predetermined number.
35 : Number of lockout stations restored 
to less than predetermined number.
36 : DLC card returned to normal 
condition.
38 : SMDR output buffer memory 
returned to normal condition.
3B : CS/ZT returned to normal condition.•
(1)
(2)Y=2
Fault Kind No.: See left column
External Alarm Kind
0 : Fault Memory/No out put of 
External Alarm
1 : Fault Memory/External Alarm is MN 
alarm
2 : Fault Memory/External Alarm is MJ 
alarm
3 : Fault Memory/External Alarm Kind 
is determined in standard data
NONE : No fault memory store
/No External Alarm outputSTART
CMEA
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized MAT-CCIS (Future Enhancement)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 183
DESCRIPTION DATA
Specify the external alarm kind which is 
automatically sent.
(1)
(2)Y=3
00-02: External Alarm Kind set by 
CMEA Y=2
0 : Sent
1 : Not sent
Specify the contents which is sent to the 
Integrated Maintenance office as external 
alarm kind.
(1)
(2)Y=4
01: Kind of Information Transferred
2: External Alarm Kind
Specify the Point Code of the office, which 
the fault information is sent to.
(1)
(2)Y=4
05: Destination office’s point code to 
which the fault information 
transferred
1-16367: Point Code
Assign the name of own office.
(1)
(2)Y=5
01: With Character Codes
20-7F: Character Code
(Max. 32 digits, 16 characters)
(See CM77 in the Command Manual.)
(1)
(2)02: With Characters
XX...XX:Office name
(Max. 16 characters)
CMEA
A
END 
						

							 NEAX2000 IVS2 CCIS System ManualPage 184  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Centralized MAT-CCIS (Future Enhancement)
NOTE:When a fault occurs, the external alarm kind registered in the IVS in the CCIS network
is displayed on Centralized MAT on the IMX office as follows:
DFTD 99/08/30 14:57 xxxxxxxxxxxxxxx
SYSTEM MESSAGE 15-0 IVS MESSAGE
xxxxxxxxx Aug 30 14:56
LP00-0-ACT
DFTD 99/08/30 14:57 XXXXXXXXX : Date of external alarm message output
SYSTEM MESSAGE 15-0 IVS MESSAGE : Means that the fault information is transferred from
the IVS.
1: 3F EE 01 00 00 00 00 00
3F  EE : Point Code of a IVS which external alarm message
outputs
01 : External alarm kind of fault information at the IVS
01: MJ alarm
02: MN alarm
04: -alarm
00 : Summary information (00 fixed)
For details, refer to the manuals for the IMX.1: 3F EE 01 00 00 00 00 00 2:00 00 00 00 00 00 00 00 3:00 00 00 00 00 00 00 00
4: 00 00 00 00 00 00 00 00
5: 00 00 00 00 00 00 00 00 6:00 00 00 00 00 00 00 00 7:00 00 00 00 00 00 00 00
8: 00 00 00 00 00 00 00 00 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Consultation Hold-All Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 185
CONSULTATION HOLD-ALL CALLS-CCIS
General Description
This feature permits a station user within the CCIS network to hold any incoming/outgoing public
network or Tie Line call while originating a call to another station within the CCIS network.
Programming
Operating Procedure
Single-Line Telephone
To hold the original call and place a second call from a Single-Line Telephone:
(1) Press the hookswitch momentarily and receive feature dial tone.
(2) The original call is placed on hold and receives Music On Hold, if provided.
(3) Dial the second station number; receive ringback tone.
(4) The second station answers; Consultation Hold-All Calls-CCIS is established.
DESCRIPTION DATA
Assign the Service Restriction Class C to 
the required stations.
(1)
(2)YY=07
X-XXXXXXXX: Station No.
XX: 00-15 : Service Restriction 
Class C
Allow the Switch Hook Flash capability in 
the Service Restriction Class C assigned 
by CM12 YY=07.
(1)
(2)YY=90, 91 
Switch Hook Flash on External Call
00-15: Service Restriction Class C 
assigned by CM12 YY=07
1 : Allow (Special Dial Tone 
Connection)
When STA-A has a C.O. line on 
Consultation Hold and is talking to STA-B. (1)
(2)117
0: Return to the original call.START
END
CM12
CM15
CM08 
						

							 NEAX2000 IVS2 CCIS System ManualPage 186  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Consultation Hold-All Calls-CCIS
To return to the original call from a Single-Line Telephone:
(1) Under any of the following conditions, the calling station can return to the original call by 
pressing the switch hook:
(a) The second station called is busy.
(b) The calling station cannot gain access to the second station because of a restriction, 
etc.
(c) The second station does not answer.
(2) If the second party hangs up, the calling station will automatically be returned to the original 
call.
(3) If the originating station switch hook flashes, a three-way call will be established.
D
term
To hold a call and place a second call from a Dterm:
(1) Press the TRANSFER key; receive feature dial tone.
(2) The original call is placed on hold and receives Music On Hold, if provided.
(3) Dial the second station number; receive ringback tone.
(4) The second station answers; Consultation Hold-All Calls-CCIS is established.
To return to the original call from a D
term:
(1) Under any of the following conditions, the calling station can return to the original call by 
pressing the TRANSFER key.
(a) The second station called is busy.
(b) The calling station cannot gain access to the second station because of a restriction, 
etc.
(c) The second station does not answer.
(2) If the second station hangs up, the calling station will automatically be returned to the 
original call.
(3) If the second station remains in the conversation, pressing the TRANSFER or ANSWER 
key returns the original call to the calling station and the second call is held.
(4) By pressing the CONF key, a Conference will be initiated. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Data Line Security-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 187
DATA LINE SECURITY-CCIS
General Description
This feature allows line circuits which are used for data transmission to be protected from
following interruptions:
Attendant Camp-On with Tone Indication (Attendant Camp-On)
Attendant Camp-On with Tone Indication-CCIS
Attendant Override
Automatic Camp-On (Attendant Camp-On)
Boss-Secretary-Message Waiting Lamp Control-D
term
(Boss/Secretary Calling)
Boss-Secretary Override-D
term (Boss/Secretary Calling)
Boss-Secretary Transfer-D
term (Boss/Secretary Calling)
Busy Verification (Attendant Override)
Busy Verification-CCIS
Executive Right Of Way (Executive Override)
Executive Right Of Way-D
term (Executive Override)
Programming
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Assign the function of Analogue Data 
station (Single Line Station with FAX or 
MODEM.) to required stations.
(1)
(2)YY=07 
X-XXXXXXXX: Station No.
0: Data stationSTART
END
CM13