NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 88  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
For North America/Other Countries:
Provide the System with Call Forwarding 
Override-CCIS.(1)
(2)371
0 : Not available
1 : Available
Specify alternative routing when the out-
going trunks of Tandem Office are all busy.(1)
(2)372
0 : Available
1 : Not available
Provide Station-to-Station Transfer over 
CCIS.(1)
(2)253
0 : Available
1 : Not Available
END
CM42
D
CM08
T/R: Transmit/Receive
+: Gain
–: Loss
PATTERNS
2ND DATAPAD DATA OF DTI 
(T/R) [dB]
00
1500 0/0
01 –2/–2
02 –3/–3
03 0/–6
04 –3/–8
05 +3/–3
06 –6/–6
07 –8/–8
08
15Not Used
~
~ 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 89
CCH Assignment
DESCRIPTION DATA
Assign an AP number to the CCH card. 
The AP number must match the switch 
settings on the CCH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
11: CCH card
Assign a CCIS channel number to each 
CCH card.
(1)
(2)YY=07
0-7: CCIS channel No.
04-15, 20-31: AP No. of the CCH card 
assigned by CM05 Y=0
Provide the common signaling channel 
and voice channel DTI routes with No. 7 
CCIS facilities.
(1)
(2)YY=90
00-63: Trunk Route No.
0: No. 7 CCIS
Assign a CCIS channel number to each 
common signaling channel and voice 
channel DTI route.
(1)
(2)YY=91
00-63: Trunk Route No.
0-7: CCIS channel No.
Assign a Circuit Identification Code (CIC) 
number to each trunk number used for 
voice channel. See assignment example in 
Example of No. 7 CCIS with Digital 
Interface on Page 98.
NOTE:The Circuit Identification Code 
(CIC) represents a circuit 
number to designate a trunk (of 
each trunk route) used as a voice 
channel in the No. 7 CCIS 
network. A CIC should not be 
assigned to a trunk used as a 
Common Signaling Channel.
(1)
(2)YY=35
000-255: Trunk No.
001-254: CIC No.
Assign the trunk number to be used as the 
common signaling channel.
(1)
(2)YY=00
0-7: CCIS channel No.
000-255: Trunk No. assigned by CM07 
CM06
CM30 START
CM05
A
CM35
CMA7
INITIAL
INITIAL 
						

							 NEAX2000 IVS2 CCIS System ManualPage 90  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
Assign a Originating Point Code (OPC) to 
each CCIS channel number.
NOTE:The Originating Point Code is 
used to designate an originating 
office in the No. 7 CCIS network. 
A single OPC should be 
assigned to all CCIS channels 
provided in the same system.
(1)
(2)YY=01
0-7: CCIS channel No.
00001-16367: Originating Point Code
Assign a Destination Point Code (DPC) to 
each CCIS channel number.
NOTE:The Destination Point Code is 
used to designate a terminating 
office in the No. 7 CCIS network. 
Usually a different DPC is 
assigned to each CCIS channel 
in the same system.
(1)
(2)YY=02
0-7: CCIS channel No.
00001-16367: DPC
Assign the Point Code of the Centralized 
Fault Reporting office, if required.
(1)
(2)YY=05
0-7: CCIS channel No.
00001-16367: Point Code of 
Centralized Fault 
Reporting office
Assign the CCIS channel to which a sig-
naling message is transferred according to 
the Point Code received.
Up to 256 point codes can be assigned.(1)
(2)00001-16367: DPC
0-7: CCIS channel No.
CMA8
CMA7
A
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 91
Numbering Plan Assignment
 For open numbering system
DESCRIPTION DATA
Assign the access code for LCR Group 0-
3.
(1)
(2)Y=0-3 Number Plan Group 0-3
X-XXXX: Access Code
A126: LCR Group 0
A127: LCR Group 1
A128: LCR Group 2
A129: LCR Group 3
Assign an Area Code Development 
Pattern number to each LCR Group.
(1)
(2)YYYY=A000
0-3: LCR Group 0-3
4000-4007: Area Code Development 
pattern No. 0-7
Assign a Route Pattern number to the 
digits to be dialed in the Area Code 
Development Pattern number assigned by 
YYYY=A000.
(1)
(2)YYYY=4000-4007 Area Code, Devel-
opment Pattern No. 0-7
X-X---X: Area Code 1-8 digits
0000-0255: Route Pattern No. 000-255
Assign an area code for Intra-Office 
Termination, if required.
(1)
(2)YYYY=4000-4007 Area Code Develop-
ment Pattern No. 0-7
X-X---X: Area Code 1-8 digits
8000: Intra-Office Termination
Specify the LCR selection priority for the 
Route Pattern number assigned by 
YYYY=4000-4007.
(1)
(2)YYYY=0000-0255 
Route Pattern No. 000-255
1: 1st priority
2: 2nd priority
3: 3rd priority
4: 4th priority
XXX ZZ
XXX : 000-255: LCR Pattern No.
ZZ : 00-63: Trunk Route No.START
CM20
A
CM8A 
						

							 NEAX2000 IVS2 CCIS System ManualPage 92  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
To delete the designated digit of an area 
code:
(1)
(2)YYYY=5000-5255 
LCR Pattern No. 000-255
153: Designation of digit to be deleted
00 : No digit deletion
01-10: Leading 1-10 digits deletion
CCC : No digit deletion
For digit addition, designate the digits to be 
added.
NOTE:Digits are always added in front 
of the number to be dialed.
(1)
(2)YYYY=5000-5255
100: Designation of Digit Addition 
Pattern No.
9000-9255: Digit Addition Pattern No. 
000-255
CCC : No digit addition

(1)
(2)YYYY=9000-9255 
Digit Addition Pattern No. 000-255
0: Entry of digit code to be added
X-X---X: Digits to be added 
(Max. 32 digits.)
Specify the maximum number of dialed 
digits sent to the CCIS network.(1)
(2)379
0 : 24 digits
1 : 16 digits
Assign the originating office number to 
each CCIS channel number if required.
(1)
(2)YY=06
0-7: CCIS channel No.
0000-9999: Office No.
Specify the maximum number of digits 
dialed by the calling party.
The maximum number of digits (including 
the area codes) should be assigned to 
each area code.
(1)
(2)Y=0-7 Area Code Development Pattern 
No. 0-7 assigned by CM8A 
YYYY=A000
X-X---X: Area Code dialed 1-8 digits
01-24 : 1-24 digits
25-79 : 25-79 digits
CM85
CM8A
A
END
CMA7
CM08 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 93
 For closed numbering system
DESCRIPTION DATA
Assign the access code for LCR Group 3.
(1)
(2)Y=0-3 Number plan Group 0-3
X-XXXX: Access Code
A129: LCR Group 3
When providing Centralized MAT or 
Number Portability, assign the access 
code for the number of digits of the 
network station number.
NOTE:For Centralized MAT or Number 
Portability, this data must be set.
(1)
(2)Y=0-3 Numbering plan Group 0-3
X-XXXX: Access Code
811-818: 1-8 digits network station No.
Assign an Area Code Development 
Pattern number to the LCR Group 
selected above.
(1)
(2)YYYY=A000
0-3: LCR Group 3
4000-4007: Area Code Development 
Pattern No. 0-7
Assign a Route Pattern number to the 
digits to be dialed in the Area Code 
Development Pattern number assigned by 
YYYY=A000.
NOTE:The digits assigned in CM20 to 
A129: LCR Group 3 must be 
entered in the Area Code 
Development Pattern table for 
access to the desired Route 
Pattern number.
(1)
(2)YYYY=4000-4007 Area Code Develop-
ment pattern No. 0-7
X-X---X: Area Code 1-8 digits
0000-0255: Route Pattern No. 000-255
Assign an area code (station number) for 
Intra-Office Termination, if required.
(1)
(2)YYYY=4000-4007 Area Code Develop-
ment Pattern No. 0-7
X-X---X: Area Code 1-8 digits
8001-8008: 1-8 digits Intra-Office 
Station
Specify the LCR selection priority for the 
Route Pattern number assigned by 
YYYY=4000-4007.
(1)
(2)YYYY=0000-0255
Route Pattern No. 000-255
1: 1st priority
2: 2nd priority
3: 3rd priority
4: 4th priority
XXX ZZ
XXX: 000-255: LCR Pattern No.
ZZ: 00-63: Trunk Route No.START
CM20
CM8A
A 
						

							 NEAX2000 IVS2 CCIS System ManualPage 94  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
To delete the designated digit of an area 
code:
(1)
(2)YYYY=5000-5255 
LCR Pattern No. 000-255
153: Designation of digit to be deleted
00 : No digit deletion
01-10: Leading 1-8 digits deletion
CCC : No digit deletion
For digit addition, designate the digits to be 
added.
NOTE:Digits are always added in front 
of the number to be dialed.
(1)
(2)YYYY=5000-5255 
LCR Pattern No. 000-255
100: Designation of Digit Addition 
Pattern No.
9000-9255: Digit Addition Pattern No. 
000-255
CCC : No digit addition

(1)
(2)YYYY=9000-9255 
Digit Addition Pattern No. 000-255
0
X-X---X: Digits to be added 
(Max. 32 digits.)
Specify the maximum number of dialed 
digits sent to the CCIS network.(1)
(2)379
0 : 24 digits
1 : 16 digits
Specify the maximum number of digits 
dialed by the calling party.
The maximum number of digits (including 
the area codes) should be assigned to 
each area code.
(1)
(2)Y=0-7 Area Code Development Pattern 
No. 0-7 assigned by CM8A 
YYYY=A000
X-X---X: Area Code dialed 1-8 digits
01-24 : 1-24 digits
25-79 : 25-79 digits
CM8A
A
END
CM85
CM08 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 95
Inter-Tenant Connection Assignment
DESCRIPTION DATA
Assign the Tenant number to each station. 
NOTE:When making a link with the IMX,   
Tenant number should be 
assigned as 01-63. 00 is not 
used.
(1)
(2)YY=04 
X-XXXXXXXX: Station No.
00-63: Tenant No. 00-63
01 : Tenant No. 01
Assign the Tenant number to each trunk. 
NOTE:When making a link with the IMX, 
Tenant number should be 
assigned as 01-63. 00 is not 
used.
(1)
(2)YY=01
000-255: Trunk No.
00-63: Tenant No. 00-63
01 : Tenant No. 01
Specify the inter-tenant connection for 
station-to-station calling or incoming call 
termination.
(See Example 1, 2.)
(1)
(2)Y=1 Station-to-Station Calling
XX ZZ   
XX: 00-63: Tenant No. of Calling Station
ZZ : 00-63: Tenant No. of Called Station
0: Restricted
1 : Allow

(1)
(2)Y=2 Incoming Call Termination
XX ZZ 
XX: 00-63: Tenant No. of Called Station
ZZ : 00-63: Tenant No. of Trunk
0: Restricted
1 : AllowSTART
CM12
CM30
CM63
END 
						

							 NEAX2000 IVS2 CCIS System ManualPage 96  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
Example 1: Inter-Tenant Connection for Station-to-Station Calling.
For the inter-tenant connection between Sta. A and Sta. B, the data assignment at Office B is as
follows.
NOTE:The inter-tenant connection between Trunk B and Sta. B (CM63 Y=2) is ineffective.
Command Code 1st Data 2nd Data
CM63 Y=1 01 02
01: Tenant No. of Calling Station (Sta. A)
02: Tenant No. of Called Station (Sta. B)0 : Restricted
1: Allow
TRUNK A
PBXNO. 7 CCISTRUNK BSTA. B
TENANT NO. STA. A
A
B
OF STA. B: 02 TENANT NO.
OF STA. A: 01
OFFICEOFFICE 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 97
Example 2: Inter-Tenant Connection for Incoming Call Termination.
For the inter-tenant connection between Trunk C (Office A) and Sta. B (Office B), the data
assignment at Office B is as follows.
NOTE:The inter-tenant restriction between Trunk B and Sta. B (CM63 Y=2) is ineffective.
Command Code 1st Data 2nd Data
CM63 Y=2 01 02
01: Tenant No. of Called Station (Sta. B)
02: Tenant No. of Trunk (Trunk C)
0: Restricted
1: Allow
NO. 7 CCISTRUNK BSTA. B
TENANT NO. TENANT NO.
OF TRUNK C: 01
OF STA. B: 02 TRUNK A TRUNK C
OFFICE
BOFFICE
A