NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 138  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
When a call is forwarded through CCIS by Call Forwarding-All Calls/-Busy Line/-Don’t Answer,
the kind of Call Forwarding and the station number which is setting the service can be indicated
on the LCD of the forwarding destination D
term.
To provide this feature, perform the following programming.
On the Forwarding side PBX (PBX-A)
On the Forwarded destination side PBX (PBX-B)
DESCRIPTION DATA
Provide the system with sending of Call 
Forwarding station information through 
CCIS.(1)
(2)373
0: To provide
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Specify the LCD digits number of the D
term 
as 24 digits.
(1)
(2)YY=95
00-15: Service Restriction Class A
assigned by CM12 YY=02
0: 24 digits
PBX-APBX-B
STATION
/TRUNKCCIS
STATION 2000Kind of Call Forwarding
Call Forwarding-All Calls/
Busy Line/Don’t Answer. Call is forwarded from
Station 2000 byand station number “2000”
are indicated on LCD.
START
END
CM08
START
END
CM12
CM15 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 139
Operating Procedure
Single-Line Telephone
To set Call Forwarding-Don’t Answer-CCIS from a Single-Line Telephone:
(1) Lift the handset; receive dial tone.
(2) Dial the Call Forwarding-Don’t Answer-CCIS access code; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst service set tone.
(4) Dial the station number to which calls are to be forwarded.
(5) Wait approximately 5 seconds; receive service set tone.
To cancel Call Forwarding-Don’t Answer-CCIS from a Single-Line Telephone:
(1) Lift the handset; receive dial tone.
(2) Dial Call Forwarding-Don’t Answer-CCIS cancellation code; receive service set tone.
Attendant Console
To set Call Forwarding-Don’t Answer-CCIS from an Attendant Console:
(1) Press an idle LOOP key.
(2) Dial the Call Forwarding-Don’t Answer-CCIS access code; receive feature dial tone.
(3) Dial the originating station number.
(4) Dial the outgoing trunk access code; receive single burst service set tone.
(5) Dial the station number to which calls are to be forwarded.
(6) Press the RELEASE key.
To cancel Call Forwarding-Don’t Answer-CCIS from an Attendant Console:
(1) Press an idle LOOP key.
(2) Dial Call Forwarding-Don’t answer-CCIS cancellation code; receive feature dial tone.
(3) Dial origination station number; receive service set tone.
(4) Press the LOOP key.
NOTE:The Attendant Console can only set/cancel Call Forwarding-Don’t Answer for stations
within the local system in which the Attendant Console resides. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 140  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
Dterm
To set Call Forwarding-Don’t Answer-CCIS from a Dterm:
(1) Lift the handset or press the SPEAKER Key; receive dial tone.
(2) Press the Call Forwarding-Don’t Answer-CCIS feature access key; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst service set tone.
(4) Dial the station number to which calls are to be forwarded.
(5) Wait approximately 5 seconds; receive service set tone. The LED lights. The LCD displays:
(6) Replace the handset or press the SPEAKER key.
To cancel Call Forwarding-Don’t Answer-CCIS from a D
term:
(1) Lift handset or press SPEAKER key; receive dial tone.
(2) Press the Call Forwarding-Don’t Answer-CCIS feature access key. The LCD displays:
(3) Dial “”; receive service set tone. The LED of the associated feature key will go out. The 
LCD displays:
(4) Replace the handset or press the SPEAKER key.
SET       XXXX
(TIME DISPLAY)
Forwarding station number D
term Series III (Dterm 65) Dterm Series E (Dterm 75)
SET       XXXX
(TIME DISPLAY)
FDN        YYY
(TIME DISPLAY) D
term Series III (Dterm 65) Dterm Series E (Dterm 75)
CF NANS     YYY
(TIME DISPLAY)
CNCL
(TIME DISPLAY) D
term Series III (Dterm 65) Dterm Series E (Dterm 75)
CANCEL
(TIME DISPLAY) 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Intercept-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 141
CALL FORWARDING-INTERCEPT-CCIS
General Description
This feature allows calls to an inoperative number, through a CCIS trunk, to be intercepted and
automatically routed to a recorded announcement informing the caller that an inoperative number
was dialed, and giving the Listed Directory Number for information.
TEL
PUBLIC 
NETWORK
MAIN OFFICEVOICE RECORDING 
MEMORY CARD
SATELLITE OFFICE
TEL
TELPUBLIC 
NETWORK TRIBUTARY OFFICE
C: 6789B: 4567 
						

							 NEAX2000 IVS2 CCIS System ManualPage 142  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Intercept-CCIS
Programming
DESCRIPTION DATA
Assign the Digital Announcement Trunk 
card number to the required LEN.
(For Intercept Announcement only.)
NOTE:The Digital Announcement Trunk 
card number must be assigned 
to the 1st LEN (Level 0), the 3rd 
LEN (Level 2), the 5th LEN (Level 
4), and the 7th LEN (Level 6) of 
each LT slot.(1)
(2)000-763: LEN
EB002-EB127: Digital Announcement 
Trunk Card No.
For PIM0/PIM1: EB002-EB031
For PIM2/PIM3: EB032-EB063
For PIM4/PIM5: EB064-EB095
For PIM6/PIM7: EB096-EB127
NOTE:EB000 and EB001 are 
dedicated to built-in Digital 
Announcement Trunk of the 
MP card.
Assign Service Restriction Class A to the 
required stations.
(For Intercept Announcement only.)
(1)
(2)YY=02
X-XXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Digital Announcement Trunk access 
in the Service Restriction Class A 
assigned by CM12 YY=02.
(For Intercept Announcement only.)
(1)
(2)YY=33
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Set the function to each Digital 
Announcement Trunk accommodated into 
the system.
(For Intercept Announcement only.)
(1)
(2)YY=00
000-001: Built-in DAT on MP card
002-127: Digital Announcement Trunk 
No. (EB002-EB127)
0A00: Call Forwarding-Intercept 
Announcement
Assign a destination for the intercepted 
call for each tenant.
(1)
(2)YY=07
00-63: Tenant No.
EB000-EB127 : Digital Announcement 
Trunk Card No.
X-XXXXXXXX : Station No.
E000 : Attendant Console
CM12
CM15
CM49 START
CM10
CM51
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Intercept-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 143
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
To record, replay, or delete a massage, 
assign the appropriate Digital 
Announcement Trunk Card access codes.
(For Intercept Announcement only.)
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
A100: Digital Announcement Trunk 
access (Record)
A101: Digital Announcement Trunk 
access (Replay)
A102: Digital Announcement Trunk 
access (Delete)
END
CM20
A 
						

							 NEAX2000 IVS2 CCIS System ManualPage 144  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Override-CCIS
CALL FORWARDING-OVERRIDE-CCIS
General Description
This feature allows a target station user (Station A) to call the station (Station B) which set Call
Forwarding-All Calls-CCIS to it through CCIS. 
Programming
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Assign Call Forwarding-Override-CCIS. (1)
(2)271
0 : Not available (BT connection)
1: AvailableSTART
END
CM08 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Transfer-All Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 145
CALL TRANSFER-ALL CALLS-CCIS
General Description
This feature allows a station user to transfer incoming or outgoing Central Office, inter-office and
inter-office calls to another station in the CCIS network, without Attendant assistance.
Programming
DESCRIPTION DATA
Assign the Service Restriction Class A to 
the required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Trunk to Trunk Transfer in the 
Service Restriction Class A assigned by 
CM12 YY=02.
(1)
(2)YY=22
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Assign the Service Restriction Class C to 
the required stations.
(1)
(2)YY=07
X-XXXXXXXX: Station No.
XX: 00-15 : Service Restriction 
Class C
Allow switch hook flash capability during 
C.O. line connection in the Service 
Restriction Class C assigned by CM12 
YY=07.
(1)
(2)YY=90, 91
00-15: Service Restriction Class C
assigned by CM12 YY=07
1 : Allow
Specify the combination of Trunk Routes 
allowing a Trunk to Trunk (CCIS) 
Connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route)
ZZ: 00-63 (Outgoing Trunk Route)
0 : Allow
1: Restricted
Specify Call Transfer from a station before 
a called station answers.
Station to Station transfer over CCIS(1)
(2)
(1)
(2)062
0 : Not available
1 : Available
253
0 : Available
CM15
CM36 START
END
CM12
CM12
CM15
CM08 
						

							 NEAX2000 IVS2 CCIS System ManualPage 146  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Transfer-All Calls-CCIS
NOTE:See also the programming for “Trunk to Trunk Connection” in the “Feature Programming
Manual”, when no release signal arrives from the incoming trunk route.
Operating Procedure
To transfer a call in progress from a Single-Line Telephone:
(1) Press the hookswitch momentarily and receive feature dial tone.
(2) Dial the third party and receive ringback tone.
(3) At this point, the station user can either:
(a) Hang up before the third party answers. The first and third parties will be connected 
when third par ty answers.
(b) Wait for the third par ty to answer and announce the transfer while keeping the first par ty 
on Consultation Hold-All Calls-CCIS. When the station user hangs up, the first and third 
parties will be automatically connected.
To transfer a call in progress from a D
term:
(1) Press the Transfer key and receive feature dial tone.
(2) Dial the third party and receive ringback tone.
(3) Wait for the third party to answer and announce the transfer while keeping the first party on 
Consultation Hold-All Calls-CCIS. When the station user hangs up, the first and third parties 
will be automatically connected. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Transfer-Attendant-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 147
CALL TRANSFER-ATTENDANT-CCIS
General Description
This service feature permits a station user, while connected to a CCIS network call, to transfer a
call to an Attendant Console located in the main office via the CCIS network.
Programming
DESCRIPTION DATA
Assign the Service Restriction Class A to 
the required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Trunk to Trunk Transfer in the 
Service Restriction Class A assigned by 
CM12 YY=02.
(1)
(2)YY=22
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Assign the Service Restriction Class C to 
the required stations.
(1)
(2)YY=07
X-XXXXXXXX: Station No.
XX: 00-15 : Service Restriction 
Class C
Allow Switch hook flash capability during 
C.O. line connection in the Service 
Restriction Class C assigned by CM12 
YY=07.
(1)
(2)YY=90, 91 
00-15: Service Restriction Class C
assigned by CM12 YY=07
1 : Allow
Specify the combination of Trunk Routes 
allowing a Trunk to Trunk (CCIS) 
Connection.
The incoming Trunk Route must provide a 
release signal for this feature. 
(See CM35 YY=05 in the Command 
Manual)
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route)
ZZ: 00-63 (Outgoing Trunk Route)
0 : Allow
1: Restrict
Specify Call Transfer from a station before 
the called attendant answers.(1)
(2)063
0 : Available
1 : Not available
CM15
CM36 START
END
CM12
CM12
CM15
CM08