NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 228  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Paging Access-CCIS
Hardware Requirements
Paging trunk (PN-4COT) × n/4 (n: Number of external paging zones)
DK card
Paging equipment provided locally. 
For cross connection of the Paging Equipment, refer to the Installation Procedure Manual.
Operating Procedure
To access paging equipment through CCIS:
(1) Lift the handset; receive dial tone.
(2) Dial the paging feature access code.
(3) Connection to paging equipment is established.
DESCRIPTION DATA
Assign paging trunk route to the trunk 
number assigned by CM10.
(1)
(2)YY=00 Trunk Route Allocation
000-255: Trunk No.
00-63: Trunk Route No.
Assign Paging Answer Zone and Kind of 
Paging to the trunk number assigned by 
CM10.
(1)
(2)YY=28 Zone/Kind of Paging
000-255: Trunk No.
X Z
X: 0-9 (Paging Answer Zone 0-9)
Z: 0 (No answer)
Specify the trunk route assigned by CM30 
Y=00 as a paging trunk route.
(1)
(2)YY=00
00-63: Trunk Route No.
05: Paging Trunk

(1)
(2)YY=08 Dial Pulse Sending Capability
00-63: Trunk Route No.
1: No Dial Pulse is sent out
Specify the combination of trunk routes 
allowing a Tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route for 
CCIS)
ZZ : 00-63 (Outgoing Paging Trunk 
Route)
0: Allow
CM35
END
CM30
A
CM36 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Restriction From Outgoing Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 229
RESTRICTION FROM OUTGOING CALLS-CCIS
General Description
This feature automatically restricts users of preselected stations from placing outgoing calls and/
or certain miscellaneous trunk calls through CCIS without Attendant assistance.
Programming
Refer to Deluxe Traveling Class Mark-CCIS on Page 188.
Operating Procedure
No manual operation is required. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 230  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Single-Digit Station Calling-CCIS
SINGLE-DIGIT STATION CALLING-CCIS
General Description
This feature allows the assignment of single digit station numbers.
Programming
DIAL XSATELLITE OFFICE MAIN OFFICE
PBX IMX/PBXNo. 7 CCIS STATION NO. X 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Single-Digit Station Calling-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 231
For Satellite Office
Operating Procedure
To operate:
(1) Lift the handset; receive dial tone.
(2) Dial the single-digit preprogrammed station number.
(3) The called station will be rung.
DESCRIPTION DATA
Assign the single-digit station number to 
LCR Group 3 (A129).
(1)
(2)Y=0-3 Number Plan Group 0-3
X: Access Code
A129: LCR Group 3
Assign an area code table to be used to 
select a route pattern table.
(1)
(2)YYYY=A000
3
4000-4007: Area Code Development 
Pattern No. 0-7
Assign the same digit which was assigned 
as the access code (in CM20) into the 
selected area code table.
(1)
(2)YYYY=4000-4007
X: Access Code
0000-0255: Route Pattern No. 000-255
Assign the route pattern table with the 
desired properties and selection of 
appropriate routes.
(1)
(2)YYYY=0000-0255
1-4: LCR Selection Priority
1: 1st
2: 2nd
3: 3rd
4: 4th
XXX ZZ
XXX : 000-255 (LCR Pattern No.)
ZZ : 00-63 (Trunk Route No.)
CM8A START
END
CM20 
						

							 NEAX2000 IVS2 CCIS System ManualPage 232  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Station-to-Station Calling-CCIS
STATION-TO-STATION CALLING-CCIS
General Description
This feature permits any station user to dial another station directly through CCIS without
operator assistance.
Programming
In addition to the programming of flexible station numbering, perform the following programming:
Operating Procedure
To place a station-to-station call:
(1) Lift the handset and receive dial tone.
(2) Dial the desired station number.
DESCRIPTION DATA
Assign a station number to each LEN.
NOTE:To the following stations, 5 or 
more digit station numbers must 
not be assigned if:
Stations are observed by 
SMDR/PMS/OAI
Front Desk Terminal/D
term 
TIMS (CIS)(1)
(2)000-763: LEN
X-XXXXXXXX: Station No.
Assign the station type to each station.
NOTE:For providing the DTMF station, 
DTMF Receivers (PN-8RST) are 
required.
(1)
(2)YY=00 Telephone types
X-XXXXXXXX: Station No.
1 : DP-10PPS
2: DTMF
3 : DTMF/DP

(1)
(2)YY=03 Kind of Telephone
X-XXXXXXXX: Station No.
15 : Ordinary station
CM12 START
END
CM10 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 233
TOLL RESTRICTION-3/6 DIGITS-CCIS
General Description
This feature allows the PBX to be programmed to restrict outgoing calls through CCIS according
to specific areas and/or Central Office codes. This restriction is determined on the basis of a
three-digit Area Code or six-digit area and Office Code numbering plan.
Programming
DESCRIPTION DATA
Provide the system with the Toll 
Restriction feature for an outgoing call by 
Speed Calling-System (System Speed 
Dialing)/Speed Calling-Station (Station 
Speed Dialing), if desired.(1)
(2)035: Speed Calling-Station 
(Station Speed Dialing)
0 : Not provided
1 : To provide
(1)
(2)044: Speed Calling-System 
(System Speed Dialing)
0 : Not provided
1 : To provide
Provide the system with Toll Diversion or 
Toll Denial.(1)
(2)119
0 : Toll Diversion (Routed to “ICPT” 
key on ATTCON)
1 : Toll Denial (Routed to Reorder 
Tone)
Assign a Trunk Restriction Class to each 
station.
(1)
(2)YY=01
X-XXXXXXXX: Station No.
X Z: Trunk Restriction Class
X: 1-8: In Day Mode
Z: 1-8: In Night Mode
1: Unrestricted (RCA)
2: Non-Restricted 1 (RCB)
3: Non-Restricted 2 (RCC)
4: Semi-Restricted 1 (RCD)
5: Semi-Restricted 2 (RCE)
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH)
CM12 START
CM08
A 
						

							 NEAX2000 IVS2 CCIS System ManualPage 234  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
DESCRIPTION DATA
Provide the Toll Restriction feature to the 
required trunk routes.
(1)
(2)YY=11
00-63: Trunk Route No.
0: To provide
Specify the route access capability for 
each restriction class.
(1)
(2)YY=51-55
00-63: Trunk Route No.
0: Restricted
1 : Allow
Assign the Area Code Development 
Pattern number for Toll Restriction 
Analysis and Maximum Digit Analysis to 
each trunk route.
(1)
(2)YY=76
00-63: Trunk Route No.
00-04: Area Code Development 
Pattern No. 0-4
Assign the Toll Restriction Patterns with 
five kinds of Trunk Restriction Classes 
assigned by CM35 YY=97. Toll Restriction 
Pattern 00-15 have already been 
programmed as shown below. If a new 
Restriction Pattern is required, change the 
data for Restriction Patterns 01-13 (00, 14 
and 15 are fixed).
(1)
(2)YY=01-13 
Toll Restriction Pattern No. 01-13
1-8: Trunk Restriction Class
0: Restricted
3: Allowed
CM81
CM35
A
B
0: Restricted
3: AllowedTRUNK
RESTRICTION
CLASSYY
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
TOLL RESTRICTION PATTERN NUMBER ON EACH TRUNK RESTRICTION CLASS
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
1 RCA 3033300033333030
2 RCB 3033000033000030
3 RCC 3030000030000030
4 RCD 3000000000000030
5 RCE 3000000000000030
6 RCF 0000000000000030
7 RCG 0000000000000030
8 RCH 0000000000000030 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 235
DESCRIPTION DATA
Specify the maximum number of digits 
dialed by the calling party. The maximum 
number of digits including the area codes 
should be assigned to each area code.
(1)
(2)Y=0-4 
Area Code Development Pattern No. 0-
4 assigned by CM8A Y=A000
X-X...X: Area Code dialed 
(Max. 8 digits)
01-24 : 1-24 digits
25-79 : 25-79 digits
Assign the area code to be restricted and 
the Toll Restriction Pattern number 
assigned by CM81 to the Area Code 
Development Pattern number assigned by 
CM35 YY=76. For example, to provide the 
Trunk Restriction Class RCB, RCC, RCD, 
RCE, RCF, RCG and RCH with the Toll 
Restriction for Area Code “00”:
Area Code=00
Toll Restriction Pattern=05
(See Toll Restriction Pattern Table on 
CM81.)
If the Toll Restriction Pattern for the same 
area code is changed according to the 
Tenant, Date, and Time, add the required 
patterns (Tenant, Date, and Time) to the 
area code.
(1)
(2)YYYY=4000-4004 
Area Code Development Pattern No. 
0-4
X-X...X: Area Code (Max. 8 digits)
B000-B015: Toll Restriction Pattern No. 
00-15
CM85
B
CM8A
C
2000 
-2007
3000 
-3003
0000 
-0255
1000 
-1015
5000 
-5255
Area 
Code4000 
-4004Time 
Patter n
Tenant 
Pa t te r n
Route 
Pa t te r n
Data 
Pa tt e r n
TR 
Pa t te r n Toll Restriction 
Pattern 00-15 
						

							 NEAX2000 IVS2 CCIS System ManualPage 236  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
DESCRIPTION DATA
To add the Tenant Pattern:
STEP 1 Assign the area code to be 
restricted and a Tenant Pattern 
number to the Area Code 
Development Pattern number 
assigned by CM35 YY=76.
STEP 2  Assign a Tenant number and a 
Route Pattern number to the 
Tenant Pattern number 
assigned by Step 1.
STEP 3  Assign a TR Pattern number to 
the Route Pattern number 
assigned by Step 2.
STEP  4  Assign a Toll Restriction Pattern 
number (assigned by CM81) to 
the TR Pattern number 
assigned by Step 3.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YYYY=4000-4004 
Area Code Development Pattern No. 
0-4
X-X...X: Area Code (Max. 8 digits)
1000-1015: Tenant Pattern No. 00-15
YYYY=1000-1015 Tenant Pattern No. 
00-15
00-63: Tenant No. 00-63
0000-0255: Route Pattern No. 000-255
YYYY=0000-0255 
Route Pattern No. 000-255
1
XXX: 000-255: TR Pattern No. 
YYYY=5000-5255 TR Pattern No. 000-
255
000
00-15 : Toll Restriction Pattern No. 
0-15
To add the Time and Data Pattern:
STEP 1 Assign an area code to be 
restricted and a Date Pattern 
number to the Area Code 
Development Pattern number 
assigned by CM35 YY=76.
STEP 2  Assign a data to apply Toll 
Restriction and a Time Pattern 
number 0-7 to the Date Pattern 
number assigned by Step 1.
Set the data for all dates, one by 
one to apply Toll Restriction.
(1)
(2)

(1)
(2)YYYY=4000-4004 
Area Code Development No. 0-7
X-X...X: Area Code (Max. 8 digits)
3000-3003: Date Pattern No. 0-3
YYYY=3000-3003 Date Pattern No. 0-3
0-6 (Date)
0: Sunday
1: Monday
2: Tuesday
3: Wednesday
4: Thursday
5: Friday
6: Saturday
2000-2007: Time Pattern No. 0-7
CM8A
C
D 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 237
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
STEP 3  Assign the starting time for the 
Toll Restriction and Route 
Pattern number to the Time 
Pattern number assigned by 
Step 2. Set the Starting Time as 
shown below.
Example:To set the 7:00 AM to 9:00 PM 
for the Toll Restriction, enter the 
following starting times one by 
one.
0700 (7:00 AM-7:30 AM)
0730 (7:30 AM-8:00 AM)
0800 (8:00 AM-8:30 AM)
2030 (8:30 AM-9:00 AM)
(1)
(2)YYYY=2000-2007 Time Pattern No. 0-
7
XX ZZ (Starting Time)
XX: 00-23 (Hours)
ZZ: 00/30 (Minutes)
0000-0255: Route Pattern No. 000-255
If Tenant Pattern is required, set 1000-1015 
(Tenant Pattern No. 0-15).
STEP 4  Assign a TR Pattern number to 
the Route Pattern number 
assigned by Step 3.
STEP  5  Assign a Toll Restriction Pattern 
number assigned by CM81 to 
the TR Pattern number 
assigned by Step 4.
(1)
(2)

(1)
(2)YYYY=0000-0255 
Route Pattern No. 000-255
1
XXX: 000-255: TR Pattern No. 
YYYY=5000-5255 TR Pattern No. 000-
255
000
00-15 : Toll Restriction Pattern No. 00-
15
END
CM8A
D
...