Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-45 Set Up System Access 
1
Figure 1-24. Typical DSA screen in SAT emulation mode
Figure 1-25. Typical DSA screen in GEDI mode 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-46 Set Up System Access 
1
Connecting a PC
You c an c onnec t your PC or lap top  to the DEFINITY ECS R8si/R8c si/R8r either 
d irec tly (50 ft [ 15 m]  or less) or remotely throug h a d ata mod ule or a mod em. 
Connecting directly to the DEFINITY ECS
You c an c onnec t d irec tly from the PC if it is 50 ft (15 m) or less from the 
DEFINITY ECS. 
1. Connec t the eq uip ment as shown in Figure 1-26
. See Table 1-6 for the 
c onnec tions b y p latform. 
!CAUTION:
For a DC-p owered  system, install an EIA 116A Isolator (c omc od e 
106005242) in series b etween the c ab le and  the TERM, DOT, or Terminal 
Ac tive c onnec tor.
Figure 1-26. A typical direct connection
Figure Notes
1 . D EFI N I TY EC S ( PPN  o n  R8 r )
2. 50-ft (15-m) M25A c ab le 
(RS-232)3. 9-to-25 pin ad ap ter if need ed
4. Comp uter with DSA or DNA
Table 1-6. PC connections by platform
Reliability R8r R8si R8csi
Standard Terminal Active TERM TERM
Hig h/Critic al—DOT—
cydfdr23 LJK 021800
2
31
4 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-47 Set Up System Access 
1
Connecting remotely to the DEFINITY ECS
To c onnec t remotely to the system, you need  one of the following  p iec es of 
hard ware:
nConnecting through a data module
nConnecting by analog modem to INADS port
Connecting through a data module
If more than 50 ft (15 m) from the DEFINITY ECS, you c an c onnec t the PC throug h 
a data module. 
1. Connec t the eq uip ment as shown in Figure 1-27
.
Figure 1-27. A typical remote connection using an 8400B (top) or 7400B 
(bottom) data module Figure Notes
1. DEFINITY ECS
2. Dig ital line c irc uit p ac k
3. B25A 25-p air c able
4. Main d istrib ution frame (MDF)
5. 103A or Luc ent mod ular wall jac k
6. 400B2 ad apter
7. D6AP p ower c ord (8400B+  only)8. Data module power supply
9. 7-ft (2-m) D8W mod ular cord
10. Data mod ule (8400B+  [ top ]  or 
7400B+  [ b ottom] )
11. 50-ft (15-m) M25A c able (RS-232)
12. Comp uter with DSA or DNA
cydfdr08 KLC021500
3
3
4
4
8
5
5
1
29
1
26
7
8
9
10
10
11
11
12
12 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-48 Set Up System Access 
1
NOTE:
With a 7400A or 7400B+  data mod ule, use a 4-wire d ig ital line c irc uit p ac k. 
With the 8400B+  d ata mod ule, use a 2-wire d igital line c irc uit p ac k.
In p lac e of a 7400B+  d ata mod ule, you c an use a 7400A d ata mod ule. If 
you do, set the 7400A to DCE Mod e.
2. Wire the d ig ital line c irc uit p ac k to the wall jac k as follows:
nFor a 7400B+ , wire to the sec ond and  third pair of the wall jac k.
nFor an 8400B+ , wire to the first p air of the wall jac k.
Setting the Data Module to DCE Mode
1. Cyc le the p ower to the d ata mod ule. The unit p erforms a self test and  
displays its operating mode.
2. Observe the d isp lay.
a. If the d isp lay reads DCE mod e, p roc eed  to the next sec tion.
b . If the d isp lay reads DTE mod e, c omp lete the following  step s:
1. Remove the p ower c ord  from the unit.
2. Remove the c over from the top  rear of the unit.
3. Remove the mod e selec t c irc uit b oard  and  turn it around .
4. Rep lac e the c over.
5. Connect the power c ord.The unit performs a self test.
NOTE:
The p ower LED must b e stead y on. If the p ower LED is b linking, the d ata 
mod ule is not c ommunic ating  with the DEFINITY ECS. Chec k the wiring  at 
the MDF, wall jac ks, and  d ata mod ule.
Adding a Data Module to the Switch
1. Add the data module to the switch by entering add data-module
 number 
or add data-module next
.
2. In the Type:
 field , typ e pdm
 and press 
En te r.
3. In the Port:
 field , typ e the loc ation of the d ig ital line c irc uit p ac k 
connec ted to the data module (for example 01A1503).
4. If system ac c ess p orts and  hunt g roup s have not b een set up , set them 
up . Refer to DEFINITY ECS Release 8 Ad ministrator’s Guid e. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-49 Set Up System Access 
1
Testing Hardware Connections
In the following  tab le, find  your d ata mod ule and  follow the instruc tions for testing  
and  troub leshooting  it.
.
Setting the Data Module Operating Mode
1. Connec t an RS-232 c ab le from the DSA/DNA c omp uter to the d ata 
mod ule. If you are using  an 8400B+ , c onnec t the DSA/DNA c omp uter to 
the data module using the supplied adapter cable.
2. Using  a terminal emulator, c onnec t to the serial p ort to whic h the d ata 
mod ule is c onnec ted , and  set the emulation to vt100 mod e.
3. Type AT
 at the p romp t and  p ress 
En t e r.The d ata mod ule should  return an 
OK. If it d oes not, b e sure that a stand ard RS-232 or EIA-232 c ab le is 
connec ted (not a null modem c able).
4. Set the operating mode as described in the following table.
5. Disc onnec t the terminal from the d ata mod ule and  rec onnec t the d ata 
mod ule to the system c ab ling . Ty p e  o f  
Data Module How to Test and Troubleshoot
8400B+ The red  LED should b e stead y on. If the red  and  g reen LEDs 
are b linking , the unit is not c ommunic ating  with the DEFINITY 
ECS. Chec k the wiring  at the MDF, wall jac k, and  the 8400B+ . 
7400B+ The Power and  TR LEDs should  b e stead y on. If the Power 
and  Data LEDs are b linking , the unit is not c ommunic ating  with 
the DEFINITY ECS. Chec k the wiring  at the MDF, wall jac k, 
and  the 7400B+ . 
7400A Set the 7400A to DCE mod e. The Power LED must b e stead y 
on. The DTR, DSR, DCD, RTS, and  CTS setting s must b e 
hig hlig hted in the d isp lay. If the Power LED is b linking , the 
d ata mod ule is not c ommunic ating  with the DEFINITY ECS. 
Chec k the wiring  at the MDF, wall jac k, and  7400A.
Ty p e  o f  
Data Module How to set the operating mode
8400B+ Typ e AT&F
 and press 
En t e r. Typ e ATS24=1
 and press 
En te r. Type AT&WØ
 and press En t e r to save the operating 
mode into non-volatile RAM.
7400A
7400B+Ty p e  AT&F
 and press 
En t e r. Typ e AT&WØ
 and press 
En te r to save the op erating  mod e into non-volatile RAM. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-50 Set Up System Access 
1
Setting the 7400B+ Options
1. Set the DIP switc hes for the 7400B+  using  Table 1-7. The DIP switc hes are 
loc ated  insid e the unit. To ac c ess them
a. Remove the p ower c ord  from the unit.
b . Remove the c over from the top  rear of the unit.
c . Set the d ip  switc hes.
d . Rep lac e the c over.
e. Connect the power c ord.The unit performs a self test.
2. If any switc hes were set in step  1, c yc le the p ower to the d ata mod ule so 
that the firmware c an read  the new switc h setting s.
Connecting by analog modem to INADS port
You c an c onnec t a PC to the DEFINITY ECS throug h a mod em.
Table 1-7. DIP Switch Settings (7400B+)
Option DIP Switch Setting
No Telep hone Connec ted 1 On
Data Metering 5 Off
Sup p ress Touc h-tone/Dial Tone 6 Off
Sp eakerp hone Disab le/Enab le 7 Off
Busyout on Loc al Loop 8 Off
Unused  DIP Switc hes 2, 3, and  4 Off 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-51 Set Up System Access 
1
1. Connec t the eq uip ment as shown in Figure 1-28.
Figure 1-28. A typical remote connection through a modem to access a remote 
DEFINITY ECS
Follow these step s to c onnec t to the DEFINITY ECS through a mod em.
1. Connec t the c omp uter to the mod em.
2. Connec t an analog  telephone line to the left most analog -line p ort on the 
mod em. 
3.Make sure that the mod em’s DIP switc hes are set as shown in Table 1-8
. Figure Notes
1. Comp uter with DSA or DNA
2. 50-ft (15-m) M25A c ab le (RS-232—
9-25 p in ad ap ter if need ed )
3. Analog  mod em
4. 7-ft (2-m) D2W mod ular c ord
5. 103A or Luc ent mod ular wall jac k
6. Main d istrib ution frame (MDF)7. Analog line circuit pack
8. Analog  trunk c irc uit p ac k
Pac ket d ata line (R8r)
Data line (R8r)
9. DEFINITY ECS
10. B25A c ab le
11. Analog  line
cydr0031 LJK 021800
1
2
3
11
4
5
78
9
1010
6 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-52 Set Up System Access 
1
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the modem.
6. Set the following  p ort setting s:
Table 1-8. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Ready normal
Data Terminal Ready override
2UP
DOWNVe r b a l re su lt  c o d e s
Numeric result codes
3UP
DOWNSuppress result codes
Display result codes
4UP
DOWNEc ho offline c ommand s
No echo, offline commands
5UP
DOWNAuto answer on first ring or higher if specified in 
NVRAM
Auto answer off
6UP
DOWNCarrier d etec t normal
Carrier detect override
7UP
DOWNLoad  NVRAM d efaults
Load factory defaults
8UP
DOWNDumb mod e
Smart mode
Baud  rate 9600
Data b its 8
Pa r it y N o n e
Stop  b its 1
Flow c ontrol hard ware 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-53 Set Ringing Option 
1
Set Ringing Option 
Figure 1-29. Ringing Option Selection
1. Chec k the ring ing  op tion for the c ountry of installation (20 Hz, 25 Hz, or 
50 Hz). See Figure 1-29
.
2. Set the slid e switc h to the p rop er setting. Refer to the lab el on the sid e of 
the power unit. Figure Notes
1. Ring ing  option switc h
evdmring LJK 062497
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-54 Activate and Administer the System 
1
Activate and Administer the System
NOTE:
The Release 8 CMC is a PPN c ab inet only. Cab inet A is the c ontrol c arrier and  
Cab inets B and  C are port c arriers.
Power Up System
Single Cabinet Installations
1. Insert the translation c ard  into the slot in the TN798B Proc essor c irc uit 
pack.
2. Fully seat the 650A Power Unit in the c ab inet.
3. Set the c irc uit b reaker at the AC load  c enter to ON. This starts the system 
reb oot p roc ess. In ab out 2 minutes, verify the sc reen d isp lays: Login:
 
Multi-Cabinet Installations
1. Insert the translation c ard  into the slot in the TN798B Proc essor c irc uit 
pack.
NOTE:
Power up  the p ort c arriers first and  the c ontrol c arrier last. 
2. Set the c irc uit b reakers at the AC load  c enter to ON. 
3. Insert the p ower sup p lies into the p ort c ab inets.
4. Insert the p ower sup p ly into the c ontrol c arrier. This starts the system 
reb oot p roc ess. In ab out 2 minutes, verify the terminal sc reen d isp lays: 
Login:
System Administration
NOTE:
An init
 log in is req uired  to perform the following . Contac t the reg ional 
CSA (Customer Software Assoc iate) to assig n the Offer Categ ory op tion. 
Maintenanc e c ap abilities to initialize the system and  ac c ess to either an 
internal or external mod em are the only c ommand  op tions availab le until 
the Offer Categ ory op tion is set.
1. To use Ac cess Security Gateway (ASG), see Appendix C, ‘‘Access 
Security Gateway’’.