Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-25 Install Main Distribution Frame and External Modem 
1
Install Main Distribution Frame and 
External Modem 
Install the MDF
!CAUTION:
The op tional MDF is a sp ec ial 110 c ross-c onnec t field  and  is smaller than stand ard  
110 c ross-c onnec t hard ware. Do not install stand ard  110 hard ware insid e the rig ht 
p anel.
NOTE:
The dep th of any equip ment installed  insid e the rig ht p anel must not exc eed 2.5 
inc hes (6.3 c m), otherwise the rig ht c over p anel c annot fit over the rig ht p anel.
The op tional MDF rep resents the trunk/auxiliary field . 
1. Mount the optional MDF to the right panel using one of the following: 
nFor b ottom-mount MDFs, refer to ‘‘Bottom-mounted MDF with 
Modem’’ on page 1-25. 
nFor top -mount MDFs (in c ab inets other than c ab inet A), 
refer to ‘‘Top-Mounted MDF’’ on page 1-27
. 
nFor d ual-mount MDFs, refer to ‘‘Dual MDFs’’ on page 1-28.
Bottom-mounted MDF with Modem
1. On the rear of the MDF, c ut the c ab le tie sec uring  the top  5 c ables to the 
MDF mounting  frame. 
2. Mount the MDF to the rig ht panel. See Figure 1-16
. 
3. Sec ure all 10 c ab les to the b ottom left b rac ket on the MDF with a c ab le tie. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-26 Install Main Distribution Frame and External Modem 
1
Figure 1-16. Typical Bottom-Mount MDF and Modem Cable Routing Figure Notes
1. Main d istrib ution frame (MDF)
2. External mod em3. Proc essor interfac e c ab le (c onnec t P2 
to mod em, c onnec t J1 to c ab le 1 on 
MDF)
4. #12 x 1-inc h should er sc rew
cadmrpnl KLC 070698
1
1
2
5
6
7
8
4 3
9
10
3
1
2
4
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-27 Install Main Distribution Frame and External Modem 
1
Top-Mounted MDF
Use this c onfig uration when the c ab inet is wall-mounted , and is near the floor. Do 
not use this c onfig uration for c ab inet A.
Figure 1-17. Typical Top-Mount MDF Cable Routing
1. On the rear of the MDF, c ut the c ab le tie sec uring  the top  5 c ables to the 
MDF mounting  frame. 
2. Mount the MDF to the rig ht panel. See Figure 1-17
. 
3. Sec ure all 10 c ab les to the b ottom left b rac ket on the MDF with a c ab le tie. Figure Notes
1. Main d istrib ution frame (MDF)
2. Connec t c ab le 1 to slot 13. #12 x 1-inc h should er sc rew
cadmmdf2 KLC 070698
1
2
5
6
7
8
4 3
9
10
1
2
3
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-28 Install Main Distribution Frame and External Modem 
1
Dual MDFs
Use this c onfig uration when mounting  two MDFs. 
Figure 1-18. Preliminary Dual-Mount MDF Cable Routing Figure Notes
1. Main d istrib ution frame (MDF)
2. Connec t c ab le 1 to slot 13. To external mod em
2
cadmrpn2 KLC 070698
1
3
1
2
5
6
7
8
4 3
9
10
1
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-29 Install Main Distribution Frame and External Modem 
1
1. On the rear of the MDF, c ut the c ab le tie sec uring  the top  5 c ables to the 
MDF mounting  frame. 
2. Mount the MDF to the b ottom p osition on the rig ht p anel. See Figure 1-18
. 
3. Sec ure all 10 c ab les to the b ottom left b rac ket on the MDF with a c ab le tie.
4. Mount the sec ond  MDF to the top  p osition on the rig ht p anel. See 
Figure 1-19
.
Figure 1-19. Typical Dual-Mount MDF Cable Routing Figure Notes
1. Main d istrib ution frame (MDF) 2. #12 x 1-inc h should er sc rew
cadmrpn3 LJK 050198
1
2
5
6
7
8
4 3
9
10
2
1
2
5
6
7
8
4 3
9
10
1
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-30 Install Main Distribution Frame and External Modem 
1
Install the External Modem
The U.S. Rob otic s Sp ortster Mod el USR 33.6 EXT external mod em is the 
rec ommend ed external mod em. Release 8 CMC systems op erate with this 
mod em set to the fac tory d efault setting s. 
NOTE:
You may use a loc ally ob tained , typ e-ap p roved  external mod em (33.6 kb p s 
and  V.34 protoc ol). Contac t your Luc ent Tec hnolog ies rep resentative for 
more information.
1. Use installer-p rovid ed  hard ware to mount the mod em. See Figure 1-16
. If 
top -mounting  MDFs or d ual-mounting  MDFs, mount the external mod em to 
the p lywood  in a loc ation whic h allows the stand ard  c onnec tion to the 
interc onnec t c ab le.
2. Route the MODEM c ab le (P2) from the Proc essor Interfac e Cab le throug h 
the c ab le troug h and  to the mod em.
3. Connec t the c ab le to the mod em. Refer to ‘‘Processor Interface Cable 
Pinout’’ on page 2-11 for the p inout of the mod em c able.
4. Plug  the mod em p ower c ord  into an elec tric al outlet and  turn on the 
mod em.
5. Mod em setup and  ad ministration is p erformed  in ‘‘External Modem Option 
Settings’’ on page 1-107. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-31 Install Equipment Room Hardware 
1
Install Equipment Room Hardware
Refer to DEFINITY Communic ations System Generic  1 and  Generic  3 Main 
Distrib ution Field  Desig n, 555-230-630, for more information.
Cross-Connect the Cabinets to the MDF
1. Cross-c onnec t the ports on the trunk and  line c irc uit p ac ks to the MDF as 
req uired. See Figure 1-21 on page 1-37
.
Allowable Circuit Packs for CMC
Table 1-2 lists the c irc uit p ac ks that c an b e used  with Release 8.
Table 1-2. Circuit Packs and Circuit Modules 
Apparatus 
Code Name
ED - 1 E5 6 8
(TN2169)
(TN567)DEFINITY AUDIX R3 System
ED - 1 E5 6 8
(TN2170)CallVisor ASAI over the DEFINITY (LAN) Gateway R1
J58890M-1
(TN801)CallVisor ASAI/Call Visor PC/LAN over the DEFINITY 
LAN Gateway R2
NAA1 Fib er Op tic  Cab le Ad ap ter Circ uit Pac k
TN429/B/C/D Analog  Direc t Inward /Outward  Dialing  (DIOD) Central 
Offic e Trunk
TN433 Voic e Synthesizer
TN436B Direc t Inward  Dialing  Trunk
TN439 Tie Trunk
TN459B Direc t Inward  Dialing  Trunk
TN464F DS1 Interfac e - T1, 24 Channel - E1, 32 Channel
TN465C Central Offic e Trunk
TN497 Tie Trunk - Italy
TN556B/C/D ISDN-BRI 4-Wire S/T-NT Interfac e
TN568 Definity AUDIX Slim
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-32 Install Equipment Room Hardware 
1
TN570C Exp ansion Interfac e
TN725B Sp eec h Synthesizer
TN726B Data Line
TN744C/D Call Classifier - Detec tor
TN746B Analog  Line
TN747/B Central Offic e Trunk
TN750B/C Announc ement
TN753/B Direc t Inward  Dialing  Trunk
TN754/B/C Dig ital Line 4-Wire DCP
TN758 Pooled Modem
TN760B/C/D/E Tie Trunk
TN762/B Hyb rid  Line
TN763B/C/D Auxiliary Trunk
TN767B/C/D/E DS1 Interfac e - T1, 24 Channel
TN789 Radio Controller
TN791 Analog  Line
TN793 Analog  Line, 24-Port, 2-Wire
TN797 Analog  CO Trunk and  Line Comb o
TN798B Proc essor
TN799B Control LAN (C-LAN)
TN801 LAN Gateway Interfac e
TN802B IP Interfac e Assemb ly
TN1654 DS1 Converter
TN2135 Analog  Line
TN2140B Tie Trunk
TN2146 Direc t Inward  Dialing  Trunk
TN2147C Central Offic e Trunk
TN2181 Dig ital Line - 16 p orts, 2-Wire DCP
Table 1-2. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-33 Install Equipment Room Hardware 
1
Circuit Pack Installation
!CAUTION:
When hand ling  c irc uit pac ks or any c omp onents of a DEFINITY System, 
always wear an authorized  wrist g round  strap . Connec t the strap  to the 
g round  c onnec tor provid ed  on the system c ab inet.
NOTE:
Unlike p revious releases of DEFINITY, the c irc uit p ac k slots in the CMC are 
not p urp le or white. This is b ec ause all of the c irc uit p ac k slots in the CMC 
are “ universal slots.”  That is, any slot c an c ontain any typ e of port circuit 
pack.  TN2182/B Tone-Cloc k - Tone Detec tor and  Call Classifier
TN2183 Analog  Line
TN2184 DIOD Trunk
TN2185/B ISDN-BRI 4-Wire S/T-TE Interfac e (Trunk Sid e)
TN2198 ISDN-BRI 2-Wire U Interfac e
TN2199 Central Offic e Trunk
TN2214/B Dig ital Line, 24-Port, 2-Wire DCP - Categ ory B
TN2215 Analog  Line, 16-Port 2-Wire - Categ ory B
TN2224/B Digital Line, 24-Port, 2-Wire DCP
TN2305 ATM Interfac e (Multimod e)
TN2306 ATM Interfac e (Sing le-Mod e)
TN2313 DS1 Interfac e
TN2464 DS1 Interfac e - T1, 24 Channel - E1, 32 Channel
TN2793/B Analog  Line 24-Port
Table 1-2. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-34 Install Equipment Room Hardware 
1
Circuit Pack Slot Loading
In g eneral, load  the c irc uit pac ks so that the numb er of p ac ks in eac h c ab inet is 
ab out eq ual and  the trunks and lines are evenly d istrib uted  among  the c ab inets. 
See Figure 1-20
. 
1. Install the TN798B Proc essor c irc uit pac k in slot 1 of Cab inet A.
2. Install the TN2182B Tone-Cloc k c irc uit p ac k in slot 2 of Cabinet A.
Load  all p ort c irc uit p ac ks starting  with Cab inet A first, Cab inet B next, and  so 
forth. Return to Cab inet A and  repeat.
3. A TN744D Call Classifier/Tone Detec tor c irc uit p ac k may b e req uired  in 
systems with heavy traffic . Install the TN744D into any p ort slot. Slot 1 of 
Cab inet B is preferred .
4. See Table 1-3
 for the rec ommend ed  c irc uit p ac k layout for the c ontrol 
c arrier and  the p ort c arriers.