Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Upgrading R6csi/R7csi to R8csi 
3-15 DEFINITY AUDIX Power Procedures 
3
nIf the AUDIX remained in the c ab inet and  the c ab inet was not p owered  
down:
1. At the AUDIX c onsole, hold  the 
crtl key and  enter cc
.
2. Enter 5
 at the p romp t. In ab out 2 minutes, the AUDIX b oots up .
3. When the system initialization is c omp lete, log  in as craft
.
4. Check for AUDIX System errors.  
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Upgrading R6csi/R7csi to R8csi 
3-16 DEFINITY AUDIX Power Procedures 
3 
						

							Adding or Removing Hardware 
4-1 Add Circuit Packs 
4
DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
4
Adding or Removing Hardware
This c hapter d etails the information req uired  to install ad ditional p ort hard ware  
assoc iated  with up g rad ing  an existing  system. 
For more information about installing  ad junc ts and  p erip heral d evic es, refer to 
DEFINITY Enterp rise Communic ations Server Release 8 Installation for Ad junc ts 
and  Perip herals.
Add Circuit Packs
When installing additional features or equipment, it may be necessary to install 
ad d itional c irc uit p ac ks. To see a list of allowab le c irc uit p ac ks, see ‘‘Allowable 
Circuit Packs for CMC’’ on page 1-31. This is a g eneral p roc ed ure to use when 
ad d ing  features or eq uip ment that req uire ad d ing c irc uit p ac ks.
1. Log  onto the system and  answer y
 to the Sup p ress Alarm Orig ination 
q uestion d uring  log in.
2. Install the c irc uit p ac k into the c arrier.
3. Type change circuit-pack
.
4. Verify the c irc uit p ac k app ears in the listing .
5. If the c irc uit p ac k c ode is not p resent, typ e the c od e manually in the 
p rop er slot.
6. Type test board long
 and  press 
En t e r to test the b oard .
7. Log  off the system after the ad dition (and  any req uired  ad ministration) is 
complete.
For information ab out ad ministering c irc uit p ac ks and  other eq uip ment, refer to 
DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-2 Add CO, FX, WATS, and PCOL 
4
Add CO, FX, WATS, and PCOL
Requirements
Eac h Central Offic e (CO), Foreign Exc hang e (FX), Personal Central Offic e Line 
(PCOL), or Wid e Area Telec ommunic ations Servic e (WATS) trunk c onnec ts to 1 
p ort of either an 8-p ort TN747B or to 1 of several CO trunk c irc uit p ac ks. 
Installation
1. Install a TN747B or a CO Trunk c irc uit p ac k in the assig ned  c arrier slot (if 
an ad d itional c irc uit p ac k is req uired ).
2. Ad minister the forms listed  und er CO, FX, WATS, or PCOL Trunk Group  in 
DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s 
Guid e.
3. Determine the p ort assig nment of the trunk from the Trunk Group  form.
Add DID Trunks
Requirements
Eac h Direc t Inward  Dial (DID) trunk c onnec ts to 1 port DID Trunk c irc uit p ac k or 
to 1 p ort of an assortment of DID trunk c irc uit pac ks.
Installation
1. Determine the p ort assig nment of the trunk from the Trunk Group  form.
2. Install a DID Trunk c irc uit p ac k in assig ned  c arrier slot (if an ad d itional 
c irc uit p ac k is req uired ).
3.Ad minister forms listed  under “ DID Trunk Group ”  in D EFINITY En terp ris e 
Communic ations Server Release 8 Ad ministrator’s Guid e. EXAMPLE:
3A0701
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Numb er
EXAMPLE:
3A0701
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-3 Add Tie Trunks 
4
Add Tie Trunks
Requirements
Eac h tie trunk c onnec ts to 1 p ort of a 4-p ort tie trunk c irc uit pac k or to an 
assortment of international tie trunk c irc uit p ac ks.
Installation
1. Determine the p ort assig nment of the trunk from the trunk g roup  sc reen.
2. Install the tie trunk or an international tie trunk c irc uit p ac k in assig ned  
c arrier slot (if an ad d itional c irc uit p ac k is req uired ).
3. For c ustomer-owned  (not leased ) tie-trunk fac ilities (suc h as c amp us 
environments), tie trunk c irc uit p ac ks p rovid e sig naling  c apab ilities 
b eyond  those sp ec ified  b y the ind ustry-wid e E&M stand ard . Use Figure 
4-1 and Table 4-1 to c hoose the p referred  sig naling  format, set switc hes 
on the c irc uit p ac k, and  ad minister the p ort.
4.Ad minister forms listed  under “ Tie Trunk Group ”  in the DEFINITY 
Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e. EXAMPLE:
3A0701
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-4 Add Tie Trunks 
4
Figure 4-1. Tie Trunk Circuit Packs (Component Side)
Table 4-1. Tie Trunk Option-Switch Settings and Administration
Installation Situation Preferred Signaling FormatE&M/SMPLX 
SwitchProt/Unprot 
SwitchAdministered
Port
Circumstance To System Far-End
Colloc ated DEFINITY E&M Typ e 1 E&M Typ e 1 E&M Unp rotec ted Typ e 1
Comp atib le Stand ard Compatib le
Inter-Build ing DEFINITY Protec ted  
Ty p e  1Protec ted 
Typ e 1E&M Protec ted Typ e 1
Comp atib le Stand ard 
Pl u sCompatib le
Protec tion
Unit
Colloc ated Net Integ rated E&M Typ e 1 Any PBX E&M Unp rotec ted Typ e 1
Stand ard
4321
PORT 4 PORT 3PORT 2PORT 1 UNPROT
PROTSMPLX
E&M
SMPLX
E&MSMPLX
E&MSMPLX
E&M
r758183 RBP 050896 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-5 Add DS1 Tie and OPS 
4
Add DS1 Tie and OPS
The TN2313 DS1 Tie Trunk and  TN767B (or later) DS1 Interfac e c irc uit p ac ks 
p rovid e c onnec tions to a 1.544-Mb p s DS1 fac ility (T1) as 24 ind ep end ent 
64-kb p s trunks. 
The TN2313 DS1 Tie Trunk, TN767B (or later) DS1 Interfac e, and  TN464C (or 
later) DS1 Interfac e c irc uit p ac ks p rovide c onnec tions to a 2.048-Mb p s DS1 
fac ility (E1) as 32 ind ep end ent 64-kb p s trunks.
Service Interruption
1. Sinc e the ad d ition of DS1 tie-trunk servic e may req uire a servic e 
interrup tion, notify the c ustomer in ad vanc e as to when the ad d ition will 
oc c ur.
2. For information ab out ad ministering DS1 Tie Trunks, refer to DEFINITY 
Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e.
Add Speech Synthesis
The Sp eec h Synthesizer c irc uit p ac k is req uired  when the Voic e Messag e 
Retrieval, Automatic  Wakeup , or Do Not Disturb  features are ac tivated . The 
c irc uit p ac k does not req uire ad ministration.
1. Determine the p ort assig nment of the Sp eec h Synthesizer c irc uit p ac k 
being added.
2. Install the Sp eec h Synthesizer c irc uit p ac k in the d esig nated  c arrier slot.
Add Code Calling Access
The tones for the Cod e Calling  feature are g enerated  b y the Tone-Cloc k c irc uit 
p acks in the port networks.
1. Install an Auxiliary Trunk c irc uit p ac k or a Sp eec h Synthesizer c irc uit p ac k 
and  c onnec t for Loud sp eaker Pag ing . The Cod e Calling  Ac c ess feature 
shares the same p orts as Loudsp eaker Pag ing . An Auxiliary Trunk c irc uit 
pack provides 4 ports for Loudspeaker Paging and Code Calling Access.
2.Ad minister the form listed  und er “ Cod e Calling  Ac c ess”  in DEFINITY 
Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-6 Add Pooled Modem 
4
Add Pooled Modem
Modem pooling supports two types of conversion resources: integrated and 
combined. 
An integ rated  c onversion requires a Pooled  Mod em c irc uit p ac k for eac h 2 
c onversion resourc es p rovid ed.
A c omb ined  c onversion requires a p ort of a TN745B or TN2136 Dig ital Line 
c irc uit p ac k and  a p ort of either an 8-p ort TN742, TN769, a 16-p ort TN746B, or a 
24-p ort TN793/B, TN2793/B Analog  Line c irc uit p ac k for eac h c onversion 
resourc e provid ed . 
The p ooled  mod em req uires a Luc ent WP90110 L7 p ower sup p ly. Althoug h 
integ rated  c onversion c an use either the L5 or L7, the c omb ined  only works with 
an L7.
!CAUTION:
The L5 and  L7 p ower sup p lies look id entic al. Chec k the lab el to b e sure you 
have the L7 b efore installing .
Determine the port assignment of the circuit packs to be added (if required).
3. Install the ap p rop riate c irc uit pac ks in assigned  c arrier slot (if req uired ).
4. For Paradyne 3800 series mod ems:
a. Type AT&F&D2&S4\D3S2=128x7V2S7=60S85=1
 and  p ress 
En te r. 
b. Type ATY0S10=100S78=2M0E0\N1&W
 and  p ress 
En t e r.
5.For other typ es of mod ems, refer to the vend or’s d oc umentation.
Settings for Modem Connected to Data Module
1. Type add data-module next
 and press En t e r.
2. Type pdm
 in the Type
 field .
3. Type x
 in the Port
 field.
4. Type dte
 in the Connected to
 field and press 
En te r.
5. Type add station next
 and press 
En t e r.
6. Type 2500
 in the Type
 field.
7. Type x
 in the Port
 field.
8. Type n
 in the Tests
 field  and  p ress 
En te r.
9. Type add modem-pool next
 and  p ress 
En te r. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-7 Add Multiple Integrated Recorded Announcement 
4
10. Typ e combined
 in the Group Type
 field.
11. Typ e 5
 in the Hold Time (min)
 field .
12. Typ e two-way
 in the Direction
 field .
13. Typ e 9600
 in the Speed
 field.
14. Typ e Full
 in the Duplex
 field .
15. Typ e async
 in the Synchronization
 field .
16. Typ e the p ort p air assig nments in the Analog
 and Digital
 fields and  
p ress 
En t e r.
Settings for Modem Connected to the Data
Terminal Equipment (DTE)
1. Type add station next
 and press En t e r.
2. Type 2500
 in the Type
 field.
3. Typ e the p ort assig nment in the Port
 field  and  p ress 
En t e r.
Add Multiple Integrated Recorded 
Announcement
TN750C c irc uit p ac ks are req uired  if the system has multiple announc ement 
c irc uit p ac ks. Up  to 5 TN750Cs are allowed  in a Release 7 or later. The 
announc ements from a TN750 or TN750B c an b e c op ied  to a TN750C. 
!CAUTION:
Do not c op y or restore announc ements from a TN750C to a TN750 or 
TN750B c irc uit p ac k, as this p roc ess may c orrupt the announc ement d ata.
1. Install the TN750C c irc uit pac k into any p ort slot. 
NOTE:
Only 1 TN750 or TN750B c an reside in the system with a TN750C. 
The TN750C need  not resid e in a c ontrol c arrier for extra p ower 
hold over.
TN750C Announcement Circuit Pack
The TN750C c irc uit p ac k c ontains on-b oard  flash memory that p rovides internal 
b ac kup  of announc ements. Thus, the TN750C c irc uit p ac k d oes not need  the 
save and  restore p roc esses. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-8 Add Multiple Integrated Recorded Announcement 
4
The TN750C c irc uit p ac k c an rep lac e a TN750 or TN750B. The d ifferenc e in 
op eration is that the TN750C automatic ally restores and  rep orts the availab ility of 
announc ements from its own internal flash memory in 5 minutes, rather than the 
40 minutes for the TN750 or TN750B.
If a c irc uit p ac k alread y has announc ements in its flash memory, the yellow LED 
flashes as the announc ements c op y to the voic e RAM. 
Save and Restore Recorded Announcements
!CAUTION:
If the yellow LED is flashing , d o not remove the c irc uit p ac k, as this will 
c orrup t the announc ement d ata.
1. Type save announcements
     and  p ress 
En t e r. 
2. To restore announc ements, typ e restore announcements
  to     and  p ress 
En t e r.
After 5 minutes (with no alterations to the announc ements), the TN750C 
automatic ally c op ies the announc ements from the voic e RAM to the internal flash 
memory. The yellow LED on the front of the TN750C flashes.
You c an only save the announc ement c ontents of 1 c irc uit p ac k at a time. For the 
c ontents of every c irc uit p ac k, save to sep arate translation c ard s. Lab el eac h 
translation c ard  so that it matc hes the c irc uit p ac k.
TN750 and TN750B Announcement Circuit Packs
To save the rec ord ed  announc ements in the system, typ e save announcements 
and  p ress 
En t e r. Use these c od es after b usiness hours or when the system is 
op erating  d uring  a low-usage p eriod. The system takes ab out 40 minutes to 
transfer the rec ord ed  announc ements from the announc ement c irc uit p ac k to the 
translation c ard . During  this time, the manag ement terminal c annot b e used  to 
ad minister the system; however, all other ad ministration terminals, if p rovid ed, 
are allowed  to p erform ad ministration p roc ed ures.
Ty p e  restore announcements
 and press 
En te r to restore the rec ord ed  
announc ements from the translation c ard to system memory.