Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-5 Comcodes for CMC 
1
406304816 ITW Linx Rep lac ement Fuse
103972758 Data Link Protec tor (1 c irc uit)
103972733  Data Link Protec tor (8 c irc uits)
407063478 Elec trostatic  Disc harg e (ESD) Wrist Strap
107731853 Sing le-Mod e Fib er Op tic  Transc eiver (300A)
106455348 Multi-Mod e Fib er Op tic  Transc eiver (9823A)
106455363 Multi-Mod e Fib er Op tic  Transc eiver (9823B)
407439975 Multi-mod e Fib er Interc onnec t Cab le — 
20 ft (6.1 m)
407598325 Sing le-mod e Fib er Interc onnec t Cab le — 
20 ft (6.1 m)
105357727 Sing le-mod e Fib er Op tic  Patc h Cord  — 
2 ft (0.6 m)
106060718 Sing le-mod e 5-d B Attenuator
106060734 Sing le-mod e 10-d B Attenuator
Table 1-1. Comcodes for Release 7.1 and Later — Continued
Comcode Description
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-6 Install the System Cabinets 
1
Install the System Cabinets
Set the Carrier Address ID — All Cabinets
Figure 1-2. Setting Carrier Address ID (Right Side)
1. Proc eed  to either ‘‘Floor-Mount the Cabinet’’ on page 1-7
 or to ‘‘Wall-Mount 
the Cabinets’’ on page 1-8. Figure Notes
1.  Carrier A switc h setting s
2. Carrier B switch setting s3. Carrier C switc h setting s
OPEN
123456
OPEN
123456
OPEN
123456
swdmdip KLC 073198
OFF1
2
3 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-7 Install the System Cabinets 
1
Floor-Mount the Cabinet
The c ab inet d imensions (with floor p ed estal) are 28.5 in. (72.4 c m) hig h, 24.5 in. 
(62.2 c m) wide, and  12 in. (30.5 c m) d eep . Maintain a servic e c learanc e of 12 in. 
(30.5 c m) on the left, rig ht, and  front of the c ab inet.
Figure 1-3. Typical Floor Mount Installation
1. Proc eed  to ‘‘Cable the System’’ on page 1-22
. Figure Notes
1. Left p anel (floor-mount p ed estal)
2. #12 x 1-in. (2.5 c m) should er 
screws3. 12 in. (30.5 c m) minimum from 
nearest ob jec t (req uired  to servic e 
the c irc uit p ac ks)
indmflor KLC 110397
1
2
3 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-8 Install the System Cabinets 
1
Wall-Mount the Cabinets 
!CAUTION:
A fully load ed  system weig hs 58 lb  (26.3 kg ). Use lifting  p rec autions. If the d oors, 
p ower unit, and  c irc uit p ac ks are removed , the unit weig hs only 29 lb  (13.1 kg ).
Install Plywood Backing onto Wall
The p lywood  and  the hard ware to mount the p lywood  are installer-p rovid ed .
NOTE:
The following  p lywood  d imensions ac c ount for the extra sp ac e need ed  to 
install the p anels on eac h side of the c ab inet. The c ab inet is 24 in. (0.6 m) 
wid e and  eac h p anel is 12 in. (0.3 m) wid e.
Single-Cabinet Installation
1. Install a 3/4-in. (2 c m) thic k sheet of 2 x 4-ft (0.6 x 1.2 m) p lywood  
horizontally onto the wall. See Figure 1-4
. 
The top  of the p lywood  must b e at least 54 in. (137 c m) from the floor. 
2 or 3 Vertically Mounted Cabinets
1. Install a 3/4-in. (2 c m) thic k sheet of 4 x 8-ft (1.2 x 2.4 m) p lywood  vertic ally 
onto the wall. See Figure 1-6
. 
2 Cabinets Vertically Mounted and 1 Cabinet Horizontally Mounted
1. Install a 3/4-in. (2 c m) thic k sheet of 4 x 8-ft (1.2 x 2.4 m) p lywood  vertic ally 
onto the wall. See Figure 1-6
.
2. Install a 3/4-in. (2 c m) thic k sheet of 2 x 4-ft (0.6 x 1.2 m) sheet of p lywood  
horizontally onto the wall. Position the p lywood to the rig ht of the first 
sheet, ac ross from Cab inet A.  
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-9 Install the System Cabinets 
1
Install Cabinet A — Wall-Mount
Figure 1-4. Left Panel Used as Mounting Template
1. Plac e the temp late on the wall ensuring  that the top  surfac e is level.
2. Mark two 1/8-in. (0.3 c m) p ilot holes in the mounting  hole loc ations.
3. Remove the temp late from the wall.
4. Drill the two p ilot holes.
5. Thread  two #12 x 1-in. should er sc rews p artially into the holes.
6. Set the c ab inet onto the wall and alig n the slots with the should er sc rews. 
See Figure 1-5
. Slid e the c ab inet to the left to hold  it in p lac e. Tig hten the 
sc rews sec urely. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-10 Install the System Cabinets 
1
Figure 1-5. Typical Wall-Mount Installation
7. Drill two lower mounting  holes using  the c ab inet as a temp late.
8. Thread  the 2 lower sc rews and  tighten.
!CAUTION:
Be sure the rig ht b ottom safety sc rew is in p lac e and  tig ht. Figure Notes
1. #12 x 1-in. should er sc rews 2. #12 x 1-inc h safety sc rew
indmins1 KLC 110397FLOOR
A
2
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-11 Install the System Cabinets 
1
Install 2 or 3 Vertically Mounted Cabinets 
Figure 1-6. Typical Vertical Multicabinet Installation
1. Sec urely tig hten the should er sc rews and  safety sc rews. Figure Notes
1. #12 x 1-inc h should er sc rews 2. #12 x 1-inc h safety sc rew
Floorindmins7 LJK 102197
5 (12.7 cm)
A
C
B
48 (122 cm)
1
12
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-12 Install the System Cabinets 
1
Install 2 Cabinets Vertically and 1 Cabinet 
Horizontally 
Figure 1-7. Typical 3-Cabinet Installation
1. Sec urely tig hten the should er sc rews and  safety sc rews. Figure Notes
1. #12 x 1-inc h should er sc rews
2. #12 x 1-inc h safety sc rew3. Sec ond  sheet of plywood
Floorindmins9 LJK 102197
29 1/2
(75 cm)
54
(137 cm)
5 (12.7 cm)
96 (244 cm)
1
12
3A
C
B
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-13 Install the System Cabinets 
1
Install Left and Right Panels — Wall-Mount
Figure 1-8. Left and Right Panel Installation
1. Alig n the c utouts in the p anels with the c ab inet hing es.
2. Drill a 1/8-inc h (0.3 c m) p ilot hole into the wall and  sec ure the p anels with 
the #12 x 1-inc h should er sc rews. Figure Notes
1. Left p anel 2. Rig ht p anel
indmins3 KLC 091197 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Installing and Cabling the Cabinets 
1-14 AC Power and Ground 
1
AC Power and Ground
!CAUTION:
The system req uires a d ed ic ated  AC p ower c irc uit that is not shared  with other 
eq uip ment and is not c ontrolled  b y a wall switc h. The AC rec ep tac le must not b e 
loc ated  und er the Main Distrib ution Frame and  must b e easily ac c essib le.
!CAUTION:
The latc h only removes DC p ower from the c ab inet. Unseating  the p ower sup p ly 
removes AC p ower from the p ower sup p ly, b ut not from the c ab inet. To remove AC 
p ower from the c abinet, p ull the AC p ower c ord  from the AC ap p lianc e c onnec tor on 
the rear of the c ab inet.
!CAUTION:
System g round ing  must c omp ly with the g eneral rules for g round ing  p rovid ed  in 
Artic le 250 of the National Elec tric al Cod e (NEC), National Fire Protec tion Ag enc y 
(NFPA) 70, or the ap p lic ab le elec tric  c ode in the c ountry of installation. 
!CAUTION:
AC mains wiring and testing must be performed by a qualified electrician and must 
c onform to Artic le 250 of the National Elec tric al Cod e (NEC), National Fire Protec tion 
Ag enc y (NFPA) 70, or the ap plic ab le elec tric  c od e in the c ountry of installation. 
Check AC Power
Eac h CMC uses an auto-ranging  85 to 264 VAC p ower sup p ly, 47 to 63 Hz, 
330 W, 4.5 amp s (100-120 VAC) or 2.3 amp s (200 to 240 VAC), at 500 VA. The 
AC p ower sourc e c an be 1 p hase of 120 VAC with neutral (100 VAC for Jap an) 
with 15 amp  c irc uit b reaker, or 1 p hase of 220 or 240 VAC (200 VAC for Jap an) 
with 10 amp  c irc uit b reaker. The AC c ord uses a NEMA 5-15P p lug or an IEC 320 
plug.
Before p owering  up  the system, c hec k the AC p ower in the eq uip ment room 
using a KS-20599 d ig ital voltmeter (DVM) (or eq uivalent).
1. Measure the AC voltag e b etween the hot and neutral sid e of the 
rec ep tac le.
2. Dep end ing  on the AC p ower sourc e, verify that the meter read s 90 to 132 
VAC or 180 to 264 VAC. If not, have a q ualified  elec tric ian c orrec t the 
problem.
3. Measure the voltag e b etween the neutral and ground  sid e of the 
rec ep tac le.
4. Verify that the meter read s 0 VAC. If not, have a q ualified elec tric ian 
c orrec t the p rob lem.
5. When finished , set the AC mains c irc uit breakers to 
OFF.