Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-39 Add IP Interface Assembly 
4
3. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
4. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
A-Law versus Mu-Law
For systems using  A-Law c omp and ing , an ad d itional p roc ed ure is nec essary. 
On the SAT:
1. Busyout the trunk g roup  assoc iated  with the IP trunk b y typing  busyout 
board 
UUCSS and  p ressing  En t e r.
In the Wind ows interfac e to TN802B:
1. Click on Control Panel > Services.
2. Highlight IP Trunk Service
, then c lic k on Stop
.
3. In the lower left-hand  c orner, rig ht-c lic k Start >  Exp lore.
4. Go to the c : d rive and  c lic k on its, then b in.
5. Double-c lic k on the its.ini file to op en it in Notep ad .
6. Und er the [ Med iaLib ]  sec tion, g o to COMPANDING= MLAW. Chang e 
MLAW
 to ALAW
.
7. Click on File > Save
 to save the file.
8. Click on File > Exit
 to exit Notep ad .
9. Click on Control Panel > Services.
10. Highlight IP Trunk Service
, then c lic k on Start
.
NOTE:
Do not selec t Startup .
After servic e has started , g o to the SAT:
1. Release the trunk g roup  assoc iated  with the IP trunk b y typing  release 
board
 
UUCSS and  p ressing  En t e r.
Assign Server and Domain Names
The Windows NT server identifies servers using a server name plus a domain 
name that loc ates the named  server in a p artic ular p art of the network. The 
TN802B IP Interfac e is ship p ed  with generic  server and  d omain names. Assig n 
rep lac ement names that are meaning ful within your network. 
1. Click on My Computer > Control Panel > Network
.
2. Selec t the Identification
 tab , then c lic k Change
.
3. Typ e the new server name in the Computer Name 
field . 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-40 Add IP Interface Assembly 
4
4. Typ e the new d omain name in the Domain
 field and  c lic k OK > OK > 
Close
.
5. When p romp ted  to reb oot the c omp uter, selec t one of the following  
op tions:
nNo
 if you have not assig ned  IP ad dresses then g o to ‘‘Assign an IP 
Address’’
nYe s
 if you have assigned  IP ad dresses. 
Assign an IP Address
1. Click on My Computer > Control Panel > Network
.
2. Click the Protocols
 tab .
3. Select TCP/IP Protocol 
from the list.
4. Click the Properties
 op tion in the Network wind ow. 
5. Verify that the Adapter
 drop  d own menu lists 2 DEC Ethernet ad ap ters. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-41 Add IP Interface Assembly 
4
!CAUTION:
Do not c hange any setting s on the ad ap ter lab eled  [ 1]  for any 
reason.
6. Selec t the DEC Ethernet ad ap ter lab eled  [ 2] .
7. Typ e a valid  IP ad d ress for the IP Interfac e server in the IP Address:
 
field .
8. Typ e the ap p rop riate sub net mask in the Subnet Mask:
 field. 
NOTE:
Not all networks req uire step s 9 throug h 18. Chec k with the loc al 
network ad ministrator to determine whic h are req uired .
9. If you use g ateways, type the IP ad d ress of the d efault g ateway for the IP 
Interfac e server in the Default Gateway:
 field.
10. Clic k on the DNS tab  and  verify that the d omain DNS server is c orrec t. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-42 Add IP Interface Assembly 
4
11. Typ e d omain name in the Domain
 field .
12. If using  DNS, c lic k 
Add  under the DNS Service Search Order
 field  and 
type its IP ad d ress.
13. Clic k on the WINS Ad dress tab . 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-43 Add IP Interface Assembly 
4
14. Make sure the [ 2]  DEC shows in the Adapter
 field.
15. If WINS server is availab le, typ e its IP ad d ress in the Primary WINS 
Server
 field .
16. If DNS is availab le, selec t Enable DNS for Windows Resolution
.
17. If the network uses an imp orted LMHOSTS file, selec t Enable LMHOSTS 
Lookup 
and Import LMHOSTS
 and c lic k OK
.
18. If the following  d ialog  b ox op ens, c lic k Ye s
:
At least one of the adapter cards has an empty primary 
WINS address. Do you want to continue?
19. Clic k the Bindings
 tab  to effec t the c hang es.
NetBIOS Interface, Server, and Workstation should now be enabled. If any 
are d isab led  (a red  c irc le with a line throug h it), review the p revious 
network-c onfig uration step s for omissions or errors.
20. Clic k Close
. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-44 Add IP Interface Assembly 
4
If administered  remotely throug h p c ANYWHERE:
21. Clic k on the p c ANYWHERE Restart Host Comp uter b utton on the toolb ar 
to restart the c omputer.
If administered  loc ally on a monitor, keyb oard, and  mouse:
21. Clic k Ye s
 in the d ialog  b ox to restart the c omp uter. 
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the p c ANYWHERE 
Restart Host Computer button on the toolbar to restart Windows NT.
Check Network Services
When the server restarts, make sure that the req uired  network servic es have 
started c orrec tly. If you see an error d ialog  b ox, then the network servic es d id  not 
start c orrec tly. Also, c hec k the NT Event Log.
1. Click on My Computer > Control Panel > Network > Services. 
Make 
sure that the following  servic es are listed:
nComp uter Browser
nMic rosoft Internet Information Server 2.0
nNetBIOS Interfac e
nRPC Config uration
nSe r ve r
nWorkstation
2. Click the Protocols 
tab , and examine the Network Protoc ols. TCP/IP 
p rotoc ol should  b e the only one listed .
3. Click OK
.
Test the External Connection to the LAN
To test the external IP c onnec tions, p ing  the IP Interfac e server and  p ing  a known 
c omp uter c onnec ted  to your network.
1. Click Start > Programs > Command Prompt
.
2. Type ping 
nnn.nnn.nnn.nnn (whic h is your IP ad d ress).
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from nnn.nnn.nnn.nnn: bytes=32 time
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-45 Add IP Interface Assembly 
4
3. At the c ommand p romp t, type ping nnn.nnn.nnn.nnn (whic h is the IP 
ad d ress of your g ateway). 
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from nnn.nnn.nnn.nnn: bytes=32 time Settings > Control Panel > 
Network
. Selec t the Adapters
 tab  and  hig hlight the [ 2]  DEC 
ad ap ter.
nClic k Properties > Change
. 
nFrom the Duplex Mod e d ropd own menu, selec t a setting  that 
matc hes the switc h/hub  that the TN802B c onnec ts to. For examp le, 
10BaseT Full Dup lex or 10BaseT No Link Test
4. At the c ommand p romp t, type ping 
nnn.nnn.nnn.nnn (whic h is the IP 
ad d ress of another external c omp uter beyond  the g ateway). 
nIf you have c onnec tivity, the system respond s with the following  
messag e:
Reply from nnn.nnn.nnn.nnn: bytes=32 time Programs > Command Prompt
.
2. Type ping 
192.11.13.9 (whic h is the IP ad d ress of the internal IP Interfac e 
server). 
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from 192.11.13.9: bytes=32 time
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-46 Add IP Interface Assembly 
4
3. At the c ommand  p romp t, typ e ping 192.11.13.8 (whic h is the IP ad d ress of 
the internal p roc essor). 
nIf you have c onnec tivity, the system respond s with the following  
messag e:
Reply from 192.11.13.8: bytes=32 time
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-47 Add IP Interface Assembly 
4
3. Attach the mouse to the MOUSE connector of the external c able 
assemb ly.
4. Plug  the monitor into an AC p ower rec ep tac le and  turn it on.
5. If upg rad ing  loc ally, reb oot Wind ows NT b y p ressing  the rec essed  reset 
b utton on the fac ep late (see Figure 4-9
) of the TN802B IP Interfac e until 
the LCD shows a flashing  MSHUT *
. When the flashing stops and the 
asterisk d isap p ears (ab out 2 min), it is safe to remove the c irc uit p ac k.
6. After the TN802B is shut d own, reseat the c irc uit p ac k to restart the 
system.
7. Log in using ctrl alt del
Upgrading IP trunks (R7) to H.323 trunks
If there are existing  IP trunk c onnec tions that you want to up g rad e to H.323 trunk 
c onnec tions, d o the following  step s. Otherwise, g o to ‘‘Upgrade to TN802B (R8)’’ 
on page 4-48
To upg rad e an existing  IP trunk (R7) to an H.323 trunk (R8) req uires first g etting  
IP information from the existing  TN802 b efore up g rad ing the TN802 to TN802B.
1. Click on My Computer > Control Panel > Network
.
2. Click the Protocols
 tab .
3. Select TCP/IP Protocol 
from the list.
4. Click the Properties
 op tion in the Network wind ow. Write d own the IP 
ad d ress, sub net ad d ress, and  g ateway ad d ress shown for ad ap tor [2] 
(see example b elow).
NOTE:
Do not use the ad d resses for ad ap ter [ 1] . 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-48 Add IP Interface Assembly 
4
5. When d one, c lic k OK, OK
.
Upgrade to TN802B (R8)
NOTE:
The upg rad e takes ab out 20 minutes.
1. Insert the flash d isk into the rig ht most slot on the TN802 IP trunk. On the 
monitor, a d ialog  b ox assig ns a d rive letter with the removab le med ia 
d esig nation; the d efault is D:. 
2. Rig ht c lic k on Start > Explore
 to op en the Wind ows NT Exploring  p ane 
and  selec t the d rive letter ind ic ated in step  1.
3. Double-clic k on Medpro 
and  selec t the Setup  ic on.
4. Follow the Install Shield  p roc ed ure to transfer all the nec essary files to the 
TN802 IP Interfac e.