Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-5 TN760D Tie Trunk Option Settings 
2
TN760D Tie Trunk Option Settings
The TN760D Tie Trunk c irc uit p ac k interfac es b etween 4 tie trunks and  the TDM 
b us. Two tip  and  ring  p airs form a 4-wire analog  transmission line. An E and  M 
p air are DC sig naling  lead s used  for c all setup . The E-lead  rec eives sig nals from 
the tie trunk and  the M-lead  transmits sig nals to the tie trunk. 
To c hoose the preferred  sig naling  format (Table 2-2
 and Table 2-3), set the 
switc hes on the TN760D and  ad minister the p ort using  Figure 2-2
 and Table 2-4. 
Table 2-2. Signaling Formats for TN760D
Mode Type
E & M Typ e I Stand ard  (unp rotec ted )
E & M Typ e I Comp atib le (unp rotec ted )
Protec ted Type I Comp atib le, Typ e I Stand ard
Sim p l e x Typ e  V
E & M Typ e  V
E & M Typ e V Revised
Table 2-3. Signaling Type Summary
Signaling Type Transmit (M-Lead) Receive (E-Lead)
On-Hook Off-Hook On-Hook Off-Hook
Type I Standard ground battery open
1/b attery
1. An op en c irc uit is p referred  instead  of b attery voltag e.
g round
Typ e I Comp atib le op en
1/b attery g round g round op en1/b attery
Type V open
1/b attery g round open g round
Typ e V Reversed g round op en g round op en 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-6 TN760D Tie Trunk Option Settings 
2
Figure 2-2. TN760D Tie Trunk Circuit Pack (Component Side)
Table 2-4. TN760D Option Switch Settings and Administration
Installation Situation Preferred Signaling FormatE&M/SMPLX 
SwitchProt/Unprot 
SwitchAdministered
Port
Circumstance To System Far-End
Colloc ated DEFINITY E&M Typ e 1 E&M Typ e 1 E&M Unp rotec ted Typ e 1
Comp atib le Stand ard Compatible
Inter-Build ing DEFINITY Protec ted 
Typ e 1Protec ted 
Typ e 1E&M Pro te c t e d Typ e  1
Comp atib le Stand ard 
Pl u sCompatible
Protec tion
Unit
Colloc ated Net 
IntegratedE&M Typ e 1 Any PBX E&M Unp rotec ted Typ e 1
Stand ard
4321
PORT 4 PORT 3 PORT 2PORT 1 UNPROT
PROTSMPLX
E&MSMPLX
E&MSMPLX
E&MSMPLX
E&M
r758183RBP050896 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-7 TN464E/F Option Settings 
2
TN464E/F Option Settings 
The TN464E/F DS1/E1 Interfac e - T1/E1 c irc uit p ac k interfac es b etween a 24- or 
32-c hannel Central Offic e/ISDN or tie trunk and  the TDM b us. 
Set the switc hes on the c irc uit p ac k to selec t b it rate and imp edanc e matc h. See 
Table 2-5
 and  Figure 2-3. If the top  switc h setting  is set to 32 c hannel, then set 
the lower switc h setting  to either 120 ohm or 75 ohm. 
Table 2-5. Option Switch Settings on TN464E/F
120 ohms Twisted  p air
75 ohms Coaxial req uiring  888B ad ap ter
32 Channel
1
1. If the 24/32 c hannel switc h is not set p er
ad ministration (or vic e versa), the c irc uit p ac k
alarms and  will not b e p resent in the list
configuration command.2.048 Mb p s
24 Channel
11.544 Mb p s 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-8 TN464E/F Option Settings 
2
Figure 2-3. TN464E/F Option Settings Figure Notes
1. TN464E/F DS1/E1 Interfac e
2. 24/32 Channel Selec tor
3. 75/120 ohm Selec tor
4. 32 Channel5. 120 ohm (shown selec ted )
6. 24 Channel (shown selec ted)
7. 75 ohm
3
4
5
1
6
2
7
tn464_ef RPY 012098 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-9 Connector and Cable Diagrams — Pinout Charts 
2
Connector and Cable Diagrams — 
Pinout Charts
See Table 2-6 for typic al lead  d esig nations. The c irc uit p ac ks and auxiliary 
eq uip ment are c lassified  as shown in the following  tab les.
Table 2-6. Lead and Color Designations
Cross-Connect 
Pin ColorAmphenol 
Pin Backplane Pin
1W-BL26 102
2 BL-W 01 002
3 W-O 27 103
4 O-W 02 003
5 W-G 28 104
6 G-W 03 004
7W-BR29 105
8BR-W04 005
9W-SL30 106
10 SL-W 05 006
11 R-BL 31 107
12 BL-R 06 007
13 R-O 32 108
14 O-R 07 008
15 R-G 33 109
16 G-R 08 009
17 R-BR 34 110
18 BR-R 09 010
19 R-SL 35 111
20 SL-R 10 011
21 BK-BL 36 112
22 BL-BK 11 012
23 BK-O 37 113
24 O-BK 12 013
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-10 Connector and Cable Diagrams — Pinout Charts 
2
25 BK-G 38 302
26 G-BK 13 202
27 BK-BR 39 303
28 BR-BK 14 203
29 BK-SL 40 304
30 SL-BK 15 204
31 Y-BL 41 305
32 BL-Y 16 205
33 Y-O 42 306
34 O-Y 17 206
35 Y-G 43 307
36 G-Y 18 207
37 Y-BR 44 308
38 BR-Y 19 208
3 9 Y-SL 4 5 3 0 9
40 SL-Y 20 209
41 V-BL 46 310
42 BL-V 21 210
43 V-O 47 311
44 O-V 22 211
45 V-G 48 312
46 G-V 23 212
47 V-BR 49 313
48 BR-V 24 213
4 9 V-SL 5 0 3 0 0
50 SL-V 25 200
Table 2-6. Lead and Color Designations — Continued
Cross-Connect 
Pin ColorAmphenol 
Pin Backplane Pin
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-11 Connector and Cable Diagrams — Pinout Charts 
2
Processor Interface Cable Pinout
 Table 2-7 shows the p inout for the Proc essor Interfac e Cab le.
Table 2-7. Processor Interface Cable Pinout
Signal NameProcessor (P1) 
(Amphenol 
Connector) AUX (J1)TERM 
(J3)DCE 
(J2)Modem 
(P2)
ACC48A 40 19
AP1 (alarm in) 2 26
AP2 (alarm in) 27 27
EXTA L M A 5 4 8
EXTA L M B 3 0 2 3
XFER4 8 3 8 3 6
MOD-CTS 21 5
MOD-DCD 46 8
MOD-DSR 8 6
MOD-DTR 7 20
MOD-GRD 20 1 & 7
MOD-RTS 34 4
MOD-RXD 33 3
MOD-TXD 45 2
TERM - C TS 9 5
TERM - D TR 4 7 2 0
TERM -G RD 3 5 1 &  7
TERM -RXD 1 0 3
TERM - TXD 2 2 2
CDR-CTS 49 5
CDR-DCD 24 8
CDR-DSR 12 6
CDR-DTR 37 20
CDR-GRD 23 1 & 7
CDR-RXD 36 3 3
CDR-TXD 48 2 2
GRD 25, 50 1-7, 
11-17, 
44-461, 7 1, 7 1, 7
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-12 Connector and Cable Diagrams — Pinout Charts 
2
Table 2-8. Port Circuit Pack Lead Designations 
Cross- 
Connect 
PinTN742/B
TN747B
TN753 
TN769 
TN2147 
TN465TN754
TN726TN760/B
TN760C 
TN760D
TN2209 TN762/BTN763 
TN763B
TN763C TN735TN767B
TN464E
TN2207TN746/B 
TN2183
TN793
TN2793 TN2224/B
1 T.1 T.1 T.1 T.1 T.1 C_5 T.1 T.1
2 R.1 R.1 R.1 R.1 R.1 R.1 R.1
3 TXT. 1 T1 . 1 TXT. 1 SZ . 1 B T. 1 C _EN A B T. 2 T. 2
4 TXR.1 R1.1 TXR.1 SZ1.1 BR.1 R.2 R.2
5 PXT. 1 E. 1 PXT. 1 S.1 L T.1 C_SYNC* T.3 T.3
6 PXR.1 M.1 PXR.1 S1.1 LR.1 R.3 R.3
7 T.2 T.2 T.2 T.2 T.2 C2D-DATA T.4 T.4
8 R.2 R.2 R.2 R.2 R.2 RDATA* R.4 R.4
9 TXT. 2 T1 . 2 TXT. 2 SZ . 2 B T. 2 TD A TA * T. 5
10 TXR.2 R1.2 TXR.2 SZ1 .2 B R.2 TRSYSN C R.5
11 PXT.2 E.2 PXT.2 S.2 LT.2 GRD T.6
12 PXR.2 M.2 PXR.2 S1.2 L R. 2 SC L K* R.6
13 T.3 T.3 T.3 T.3 T.3 T.7
14 R.3 R.3 R.3 R.3 R.3 R.7
1 5 TXT. 3 T1 . 3 TXT. 3 SZ . 3 B T. 3 T. 8
16 TXR.3 R1.3 TXR.3 SZ1 .3 B R.3 PA H ER* R.8
1 7 PXT. 3 E. 3 PXT. 3 S. 3 L T. 3 T. 5 T. 9
18 PXR.3 M.3 PXR.3 S1.3 LR.3 C_48V R.5 R.9
19 T.4 T.4 T.4 T.4 T.4 T.6 T.10
20 R.4 R.4 R.4 R.4 R.4 R.6 R.10
2 1 TXT. 4 T1 . 4 TXT. 4 SZ . 4 B T. 4 C _P2 SC L K T. 7 T. 1 1
22 TXR.4 R1.4 TXR.4 SZ1.4 BR.4 LI
 (RX) R.7 R.11
2 3 PXT. 4 E. 4 PXT. 4 S. 4 L T. 4 L O *  ( TX) T. 8 T. 1 2
24 PXR.4 M.4 PX4.4 S1.4 LR.4 LBACK1 R.8 R.12
2 5 T. 5 T. 5 T. 5 T. 5 T. 5 G N D T. 9 T. 1 3
26 R.5 R.5 R.5 R.5 R.5 C _5V R.9 R.13
2 7 TXT. 5 T1 . 5 TXT. 5 SZ . 5 B T. 5 T. 1 0 T. 1 4
28 TXR.5 R1.5 TXR.5 SZ1.5 BR.5 R.10 R.14
2 9 PXT. 5 E. 5 PXT. 5 S. 5 L T. 5 T. 1 1 T. 1 5
30 PXR.5 M.5 PXR.5 S1.5 L R. 5 C _RST R.11 R.15
31 T.6 T.6 T.6 T.6 T.6 T.12 T.16
32 R.6 R.6 R.6 R.6 R.6 R.12 R.16
3 3 TXT. 6 T1 . 6 TXT. 6 SZ . 6 B T. 6 RD A TA T. 1 7
34 TXR.6 R1.6 TXR.6 SZ1 .6 B R.6 TD A TA R.17
3 5 PXT. 6 E. 6 PXT. 6 S. 6 L T. 6 TRSYN C T. 1 8
36 PXR.6 M.6 PXR.6 S1.6 L R. 6 GRD R.18
37 T.7 T.7 T.7 T.7 T.7 SCLK T.19
38 R.7 R.7 R.7 R.7 R.7 R.19
3 9 TXT. 7 T1 . 7 TXT. 7 SZ . 7 B T. 7 T. 2 0
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-13 Connector and Cable Diagrams — Pinout Charts 
2
* Denotes hig h side of line.
40 TXR.7 R1.7 TXR.7 SZ1.7 BR.7 R.20
41 PXT.7 E.7 PXT.7 S.7 LT.7 GRD T.13 T.21
42 PXR.7 M.7 PXR.7 S1.7 LR.7 R.13 R.21
4 3 T. 8 T. 8 T. 8 T. 8 T. 8 C _PRES* T. 1 4 T. 2 2
44 R.8 R.8 R.8 R.8 R.8 R.14 R.22
4 5 TXT. 8 T1 . 8 TXT. 8 SZ . 8 B T. 8 T. 1 5 T. 2 3
46 TXR.8 R1.8 TXR.8 SZ1.8 BR.8 DC2_DATA R.15 R.23
4 7 PXT. 8 E. 8 PXT. 8 S. 8 L T. 8 LI
*  ( RX) T. 1 6 T. 2 4
48 PXR.8 M.8 PXR.8 S1.8 L R. 8 LO ( TX) R.16 R.24
49 GRD GRD GRD GRD GRD GRD LBACK2 GRD GRD
50 GRD GRD GRD GRD GRD GRD GRD GRD GRD
Table 2-9. DS1 Interface Cable H600-307 (and C6C)
50-Pin 15-Pin
Pin Color Designation Pin Color Designation
02 W-BL
03 BL-W
47 W-G LI (High)
11 W-G LI (High)
22 G-W LI
03 G-W LI
48 W-BR LO 09 W-BR LO
23 BR-W LO (High)
01 \BR LO (High)
49 W-SL LOOP2 06 W-SL LOOP2
24 SL-W LOOP1 05 SL-W LOOP1
All other pins are empty.
Table 2-8. Port Circuit Pack Lead Designations  — Continued
Cross- 
Connect 
PinTN742/B
TN747B
TN753 
TN769 
TN2147 
TN465TN754
TN726TN760/B
TN760C 
TN760D
TN2209 TN762/BTN763 
TN763B
TN763C TN735TN767B
TN464E
TN2207TN746/B 
TN2183
TN793
TN2793 TN2224/B
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Completing Installation and Cable Pinouts 
2-14 Connector and Cable Diagrams — Pinout Charts 
2
Table 2-10 shows the p inouts for the TN2185 ISDN-BRI 4-wire S Interfac e. 
Table 2-10. TN2185 ISDN-BRI — 4-Wire S Interface Pinout
Port Signal Cross-Connect Pin  Color Amphenol Pin  Backplane  Pin
1 TXT.1 1 W-BL 26 102
TXR.1 2 BL-W 01 002
PXT.1 3 W-O 27 103
PXR.1 4 O-W 02 003
2 TXT.2 5 W-G 28 104
TXR.2 6 G-W 03 004
PXT. 2 7 W-B R 2 9 1 0 5
PXR. 2 8 BR- W 0 4 0 0 5
3 TXT.3 9 W-SL 30 106
TXR.3 10 SL-W 05 006
PXT.3 11 R-BL 31 107
PXR.3 12 BL-R 06 007
4 TXT.4 13 R-O 32 108
TXR.4 14 O-R 07 008
PXT. 4 1 5 R-G 3 3 1 0 9
PXR. 4 1 6 G - R 0 8 0 0 9
5 TXT.5 17 R-BR 34 110
TXR.5 18 BR-R 09 010
PXT. 5 1 9 R- SL 3 5 1 1 1
PXR. 5 2 0 SL - R 1 0 0 1 1
6 TXT.6 21 BK-BL 36 112
TXR.6 22 BL-BK 11 012
PXT.6 23 BK-O 37 113
PXR.6 24 O-BK 12 013
7 TXT.7 25 BK-G 38 302
TXR.7 26 G-BK 13 202
PXT. 7 2 7 B K- B R 3 9 3 0 3
PXR. 7 2 8 B R- B K 1 4 2 0 3
8 TXT.8 29 BK-SL 40 304
TXR.8 30 SL-BK 15 204
PXT. 8 3 1 Y- BL 4 1 3 0 5
PXR.8 32 BL-Y 16 205