Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-29 Add IP Interface Assembly 
4
NOTE:
The c ustomer provid es the IP add ress, sub net mask, and  g ateway 
address.
At this time the TN802B LCD read s PC BOOT *
, and  ab out 3 to 4 minutes 
later read s MEDPRO *
 with the asterisk flashing
.
Test the External Connection to the LAN
To test the external IP c onnec tions, p ing the IP Interfac e server, and  p ing  a 
known c omp uter c onnec ted  to your network. If everything  is c onfig ured c orrec tly, 
the Result
 c olumn on the Ping  Results sc reen read s pass
. If it read s abort
, 
verify the IP-ad d ress information and  c hec k the c onnec tivity, inc lud ing  the 
cabling.
1. Type ping ip-address 
nnn.nnn.nnn.nnn board UUCSS and p ress En t e r. 
Th e  v a r i a b l e  
nnn.nnn.nnn.nnn is the IP ad d ress of the TN802B IP 
Interfac e and  
UUCSS is the c ab inet, c arrier, and  slot of the TN802B IP 
Interfac e.
change ip-interfaces                                            Page   1 of   2 
                                                                                
 Network regions are interconnected?  n
  En-                                                                        Net
 abled Type   Slot  Code Sfx Node Name       Subnet Mask     Bcast/Gway 
Addr Rgn
   n   C-LAN  01A09 TN799    clan-a1         255.255.255.0   192.168.1 .100 1 
y  MEDPRO 01A13 TN802  B med-a1  255.255.255.0  192.168.1 .21  1 
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .      
   n                                         255.255.255.0      .   .   .       
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-30 Add IP Interface Assembly 
4
2. Type ping ip-address nnn.nnn.nnn.nnn board UUCSS and p ress En t e r. 
Th e  v a r i a b l e  
nnn.nnn.nnn.nnn is the IP ad d ress of the c ustomer’s 
g ateway and  
UUCSS is the c ab inet, c arrier, and  slot of the TN802B IP 
Interfac e.
3. Type ping ip-address 
nnn.nnn.nnn.nnn board UUCSS and p ress En t e r. 
Th e  v a r i a b l e  
nnn.nnn.nnn.nnn is the IP ad d ress of another c omp uter 
b eyond  the g ateway and  
UUCSS is the c ab inet, c arrier, and  slot of the 
TN802B IP Interfac e.
The TN802B IP Interfac e is now installed  in the DEFINITY c arrier and  c onnec ted  
to the IP network.
Installing in IP Trunk Mode
NOTE:
IP Trunk mod e should  only b e used  to maintain c omp atib ility with existing  
Release 7 IP Trunk or ITS-E installations. We strong ly rec ommend  that 
Med Pro mod e b e used  whenever p ossib le.
Prepare for Installation
Have the following  eq uip ment on site b efore your ship ment arrives:
nA mouse, keyboard , and  VGA monitor for use d uring  the installation of the 
server. You also need  AC p ower outlets for the mod em and monitor.
nThree ad joining , unoc c up ied  p ort slots in the DEFINITY ECS
The TN802B IP Interfac e slid es into only 1 slot, b ut its fac ep late oc c up ies 
3 slots.
nA 10 BaseT or 10/100 BaseT Ethernet c onnec tion into the c ustomer’s loc al 
area network (LAN)
nA valid , unused IP ad d ress on the c ustomer’s LAN that c an b e assig ned  to 
the IP Interfac e server. You also need  the sub net mask, d efault g ateway, 
d omain name, and  so forth from the c ustomer’s network ad ministrator.
nAn analog telep hone line reserved  for the IP Interfac e d iag nostic  mod em
ping ip-address 192.168.10.21                                                   
                                                                                
                          PING RESULTS
  End-pt IP        Port      Port Type  Result    Time(ms)  Error Code
  192.168.10.21    01A13 MEDPRO PASS  10 1124  
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-31 Add IP Interface Assembly 
4
nA valid  telep hone numb er reserved  for the IP Interfac e d iag nostic  mod em
If non-U.S. c ustomer:
nMod em c omp arab le to a U.S. Rob otic s, Inc . Sp ortster Mod el USR 33.6 
EXT.
nA c ab le from the mod em to the TN802B external c ab le assemb ly.
We rec ommend  that you p rotec t the c ab inet where the IP Interfac e is installed  
with an uninterrup tib le p ower system (UPS).
Check your Shipment
When your DEFINITY Med ia Proc essor ord er arrives at the c ustomer’s site, c hec k 
the c ontents (see Table 4-6
).
1. Insp ec t the ship p ing  c arton for d amag e b efore op ening  it. If the b ox is 
damaged, do not open it. Inform the ship p ing  c omp any, and  ask for 
instruc tions on filing a c laim.
2. If the b ox is und amag ed , c hec k the c ontents ag ainst the p ac king  slip . 
Chec k the c ondition of eac h c omp onent, and note any d amag e or 
shortag es on the p ac king  slip . The c arton should  c ontain the following  for 
eac h IP Interfac e ord ered :
.
The TN802B external c ab le assemb ly is a bund le of c ab les with an amp henol 
c onnec tor at the end  of the b und le and  various PC-typ e c onnec tors (VGA, 
Universal Serial Bus [ USB] , mouse, keyb oard , Ethernet, mod em, and  COM2) at 
the end s of the ind ivid ual c ab les. See Figure 4-7
. Look for the lab el where the 
b und le enters the amp henol c onnec tor.
Table 4-6. Required Hardware
Comcode/Code Description Quantity
J58890MA-1 L30 TN802B IP Interfac e Assemb ly
1
601939804 H600-512,G1 external c ab le assemb ly 1
407633999 U.S. Rob otic s Sp ortster external 
mod em, mod el numb er USR 33.6 EXT 
(U.S. c ustomers only) 
1
1. For non-U.S. customers, you need  a mod em c omparable to the U.S. Rob otic s
Sp ortster and a serial c able. 
1
601087091 20-ft DB-25 serial c ab le from modem 
to TN802B external c ab le assemb ly 
(U.S. c ustomers only) 
2
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-32 Add IP Interface Assembly 
4
Figure 4-7. TN802B IP Interface External Cable Assembly
3. Read  and  follow any d irec tions inserted  into the p ac kag e b y the fac tory.
Connect the Cables
1. Determine into whic h p ort slot you are p utting  the TN802B IP Interfac e.
NOTE:
Make sure that at least 3 ad joining  slots are free.
2. From the rear of the c ab inet, c onnec t the amp henol c onnec tor on the 
external c ab le assemb ly to the b ac kp lane c onnec tor c orrespond ing  to 
that slot (the hig hest numbered  c onnec tor of the 3 slots required ). Figure Notes
1. Amp henol c onnec tor to c onnec tor 
c orresp ond ing  to TN802B slot
2. To VGA monitor
3. To USB (not used )
4. To keyb oard5. To mouse
6. To ethernet
7. 25-p in male c onnec tor to mod em
8. 25-p in male c onnec tor to COM2 
cbdfocto AWF 122398
2
1
345678 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-33 Add IP Interface Assembly 
4
Connect the Modem
NOTE:
These instruc tions are for c onnec ting  the U.S. Rob otic s modem sup p lied  to 
U.S. c ustomers only. If using  a d ifferent mod em, follow the manufac turer’s 
instruc tions on c onnec ting  the mod em.
1. Connec t the RS232 p ort of the mod em to the MODEM c onnec tor of the 
TN802B external c ab le assembly. 
NOTE:
Chec k the lab els near the c onnec tors; the MODEM and  COM2 
c onnec tors look the same.
2. Connec t an analog  telephone line to the leftmost analog -line p ort on the 
mod em as shown in Figure 4-8
. 
3. Make sure that the mod em’s DIP switc hes are set as shown in 
Figure 4-8
 and Table 4-7. 
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the mod em using  the switc h on the front of the mod em.
Figure 4-8. External Modem Connections for U.S. Robotics Sporster Figure Notes
1. Connec t analog  line here.
2. DIP switc h 5 must b e up .3. Connec t MODEM c onnec tor here.
4. Connec t p ower c onnec tor here.
12345678
modfrobo KLC 030499
234
1 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-34 Add IP Interface Assembly 
4
Connect the Monitor, Keyboard, and Mouse
NOTE:
Only make these c onnec tions if ad ministered  loc ally. Not nec essary if 
ad ministered  remotely.
You must c onnec t these b efore inserting  the TN802B IP Interfac e.
1. Attac h a VGA monitor to the VGA c onnec tor of the TN802B IP Interfac e 
external c ab le assemb ly.
2. Attac h the keyb oard  to the KEYBOARD c onnec tor of the external c ab le 
assemb ly.
3. Attach the mouse to the MOUSE connector of the external c able 
assemb ly.
4. Plug  the monitor into an AC p ower rec ep tac le and  turn it on.
Table 4-7. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Read y normal
Data Terminal Read y overrid e
2UP
DOWNVe r b a l  r e s u lt  c o d e s
Numeric  result c od es
3UP
DOWNSuppress result codes
Disp lay result cod es
4UP
DOWNEc ho offline c ommand s
No ec ho, offline c ommand s
5UP
DOWNAuto answer on first ring or higher if specified in NVRAM
Auto answer off
6UP
DOWNCarrier d etec t normal
Carrier d etec t overrid e
7UP
DOWNLoad  NVRAM d efaults
Load  fac tory d efaults
8UP
DOWNDumb  mod e
Sm a rt  m o d e 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-35 Add IP Interface Assembly 
4
Connect the Ethernet
1. Connec t the network c ab le to the ETHERNET c onnec tor on the TN802B 
external c ab le assemb ly.
NOTE:
You need  a CAT5 or better c ab le for 100-Mb yte operation.
Install the Circuit Pack
!CAUTION:
When ad d ing  or rep lac ing  any hard ware, b e sure to ground  yourself 
ag ainst elec trostatic  d isc harge (ESD) b y wearing  a g rounded  wrist strap .
NOTE:
The TN802B IP Interfac e is hot-swap p ab le, so you d o not need  to p ower 
d own the c arrier to install it.
If you need  to remove the TN802B IP Interfac e from the c arrier at a later 
time, shut down Wind ows NT first b y p ressing the rec essed reset button on 
the fac ep late (see Figure 4-9
) of the TN802B IP Interfac e until the LCD 
shows a flashing MSHUT *
. When the flashing  stop s and  the asterisk 
d isap p ears (ab out 2 min), it is safe to remove the c irc uit p ac k. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-36 Add IP Interface Assembly 
4
Figure 4-9. TN802B IP Interface faceplate
NOTE:
To p rop erly seat the c irc uit p ac k, p ush firmly on the front of the fac ep late 
until the latc h reac hes the b ottom rail of the c arrier. Then c lose the latc h 
until it is fully eng ag ed .
1. Insert the TN802B IP Interfac e into the rig htmost of the three slots you 
reserved  for it (see Figure 4-10
).
When you p lug  in the TN802B IP Interfac e, the c irc uit p ac k starts to b oot 
and  the LCD read s PC Boot 
then after ab out 3 to 4 minutes it c hang es to 
IP TRK *
, the default mod e. Figure Notes
1. LCD d isp lay
2. Reset b utton (rec essed )
3. Red  b oard  status LED4. PCMCIA c ard slot
5. Yellow PCMCIA d isk-in-use LED
1
2
3
4
5
fpdfmapd KLC 030899 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-37 Add IP Interface Assembly 
4
Figure 4-10. J58890MA-1 L30 IP Interface Assembly
Test the Modem
1. Check for dial tone.
2. Contac t Luc ent Tec hnolog ies Customer Sup p ort and  ask a rep resentative 
to d ial into your IP Interfac e server. 
Administer the IP Interface
Ad minstration is d one either loc ally or remotely. If ad ministered  loc ally, p roc eed  
with the following  ad minstration step s on the attac hed  keyb oard , mouse, and  
monitor. If administered  remotely, c all your servic e rep resentative to start the 
p roc ess.
Administration Steps
1. Log in as craft
.
2. Type change circuit-pack
 and  p ress 
En te r.
456
789
1
0
1
11
21
3
1
41
51
6
indfmapd KLC 031299 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-38 Add IP Interface Assembly 
4
3. Chec k the Cod e c olumn to see if the slots ab ove the TN802B say 
DSMAPD or MEDPRO.
.
4. If MEDPRO, g o to the entry just ab ove the TN802B that says MEDPRO.
5. Type DSMAPD, and press 
En te r. Chang ing the one entry automatic ally 
c hang es the entry ab ove it. If it is in IP Trunk mode, you g et the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
Log onto the TN802B Interface Server 
If administered  remotely throug h p c ANYWHERE:
1. Dial in to the server through pcANYWHERE using the dialup number 
supplied. 
2. Clic k on the p c ANYWHERE Remote Host Computer b utton on the toolb ar 
to send  
CTRL ALT DEL to the host.
3. Type administrator
 in the User Name
 field .
4. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
5. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
If administered  loc ally on a monitor, keyb oard, and  mouse:
1. Press 
CTRL, ALT, and  DEL simultaneously.
2. Type administrator
 in the User Name
 field .
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: DSMAPD RESERVED-IP
01: TN754  DIGITAL LINE  12: DSMAPD  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict.