Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation, Upgrades, And Additions For Compact Modular Cabinets Manual

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-49 Add IP Interface Assembly 
4
NOTE:
In the Finish d ialog  b ox, selec t I will restart later
. Do not 
select Restart computer
.
This would  b e a g ood  time to read  the Read me.txt file.
5. Click on Start > Settings > Control Panel > Services
.
6. Select IP Trunk 
and click on Startup
.
NOTE:
Do not c lic k on Start.
7. Under Startup Type, select Disabled
 and  c lic k OK
 to d isab le IP Trunk 
mod e.
NOTE:
If IP trunk and  Med Pro servic es are b oth set to automatic , the 
TN802B d efaults to IP Trunk and  MedPro features c annot be used .
8. Select MedPro 
and c lic k on Startup
.
NOTE:
Do not c lic k on Start.
9. Under Startup Type, select Automatic
 and  c lic k OK
 to enab le Med Pro 
mod e.
10. Clic k Start > Shut Down
 and  selec t Restart the computer?
or on the TN802:
Press the rec essed  reset b utton on the fac ep late (see Figure 4-9
) until the 
LCD shows a flashing  MSHUT *
. When the flashing stops and the asterisk 
d isap p ears (ab out 2 min), reseat the c irc uit p ac k to restart the system.
or on the SAT:
a. Type busyout board 
UUCSS 
and press En te r .
b. Type reset board
 
UUCSS and  p ress En te r. 
c . Typ e release b oard  
UUCSS and  p ress En te r. 
Onc e the system is c omp letely initialized , the LCD read s MEDPRO *
.
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the 
p c ANYWHERE Restart Host Comp uter b utton on the toolb ar to 
restart Wind ows NT. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-50 Add IP Interface Assembly 
4
11. Affix the new TN802B lab el to the c irc uit p ac k.
12. Disc onnec t the monitor, keyb oard , and  mouse.
Circuit Pack Verification
1. Type change circuit-pack
 and  p ress En te r.
2. Chec k the Cod e c olumn to see if it says DSMAPD or Med Pro.
.
3. To c orrec t it, g o to the entry just above the TN802B that says DSMAPD.
4. Type MEDPRO, and press 
En t e r. Changing  the one entry automatic ally 
c hang es the entry ab ove it. If it is in IP Trunk mode, you g et the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
5. To c omp lete the ad ministration, refer to the DEFINITY ECS Release 8 
Network Connec tivity b ook.
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: MEDPRO RESERVED-IP
01: TN754  DIGITAL LINE  12: MEDPRO  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-51 Add TTC Japanese 2-Mbit Trunks 
4
Add TTC Japanese 2-Mbit Trunks
The TN2242 Jap an 2-Mb it trunk interc onnec ts DEFINITY to other vend or 
eq uip ment in Jap an as well as to other DEFINITY switc hes through the Time 
Division Multip lexor (TDM).
Installing the trunk
1. Determine the p ort assig nment of the trunk from the Trunk Group  form.
2. Install a TN2242 c irc uit p ac k in assigned  c arrier slot.
3. Connec t the H600-513 c ab le from the DEFINITY c ab inet to the Time 
Division Multip lexor d evice.
4. To ad minister forms, see the following  sec tions in the DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e.
nFor ISDN ap p lic ations, see ISDN Servic e.
nFor non-ISDN applications, see Managing Trunks.
Installing an Integrated Channel
Service Unit (ICSU) Module
The integ rated c hannel servic e unit (ICSU) is a c omb ination of a 120A CSU 
mod ule integ rated  with a DS1 c irc uit p ac k. Use this d evic e with the 700A DS1 
loop b ac k jac k when testing  the DS1 sp an. 
Checking for required components
The integ rated c hannel servic e unit (ICSU) p ac kag e c ontains:
n120A CSU mod ule
nCab le H700-383
4-pair modular cord
Group  2, 50-ft (15.2-m) c ab le (stand ard )
nCord  DW8A-DE
4-p air mod ular c ord  to alarm c ontac ts
nDS1 c irc uit p ac k EXAMPLE:
3A0701
Cab inet (Port 
Network)Carrier Slot 
Numb erPo rt  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-52 Installing an Integrated Channel Service Unit (ICSU) Module 
4
The b asic  ICSU req uires a TN474E or TN777D or later suffix. The 
enhanc ed  integ rated  c hannel servic e unit req uires a TN474F or TN777E or 
later suffix.
Installing the 120A CSU
See Figure 4-11. 
Figure 4-11. 120A Channel Service Unit Module
!CAUTION:
Do not p lug  the 120A into any c irc uit p ac k other than a TN474F or TN777E 
or later release/vintag e. Do not c onnec t the 120A to any interfac e other than 
a network smart jac k.
1. Rear of carrier containing DS1 circuit pack
2. 120A CSU
3. To 25-pair connector on rear of carrier4. DW8A-DE 4-pair cord to alarm contacts (optional)
5. 4-pair cord to network interface (H700-383)
1cydfcsu1  KLC 033099120A
CSU MODULE
MADE IN U.S.A.ALARMCONT
ACTSNETWORK
1
2
3
45 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-53 Installing an Integrated Channel Service Unit (ICSU) Module 
4
Be sure the DS1 c irc uit p ac k is set for 24-c hannel op eration (1.544 Mbp s). 
The 120A d oes not op erate with the 32-c hannel interfac e. A switc h on the 
c irc uit p ac k or ad ministration sets this op tion. 
!CAUTION:
Always wear an antistatic  wrist strap  when installing  a 120A mod ule. Do not 
touc h the external alarm c ab le when it is c onnec ted  to the 120A. Static  
d isc harg e c an d amag e c onnec tor terminals and  relays. 
1. Unp lug  the DS1 c irc uit p ac k from its slot.
2. Install a 4C retainer in the 50-p in p lug  assoc iated  with the DS1 c irc uit p ac k 
slot.
3.Plug  the 120A’s 25-p air c onnec tor d irec tly into the p lug  assoc iated  with 
the DS1 c irc uit p ac k slot. 
4. Sec ure the 4C retainer around  the 120A.
5. Attac h the sup p lied  H700-383 c able to the 120A and to the network smart 
jac k. 
This c ab le is d irec tional. To determine the end  that c onnec ts to the 120A, 
p erform a c ontinuity test b etween pins 3 and  7. The end  with this 
c ontinuity is the 120A end . The shield  is g round ed  only at the 120A end .
Use the c able p rovid ed . If c ab ling  other than that p rovided  with the 120A 
is used , ob serve the following  g uid elines:
nUse 24-g aug e wire that p rovid es ind ividually shield ed , twisted  p airs 
for transmit and  rec eive sig nals. Use the c ab le b etween the 
network interfac e and  the 120A. Ground  the shield s of this c able 
only at the 120A end to avoid  g round  loop s.
nCab ling  b etween the network interfac e and  120A c an have no 
bridge taps.
nIf using  stand ard  house riser c ab le for c onnec tions b etween the 
network interfac e and  the 120A, maintain a 100-p air sep aration 
b etween the rec eive and  transmit twisted  p airs.
nIf using  stand ard  house riser c ab le for c onnec tions b etween the 
network interfac e and  the 120A, allow no more than 2 c ross 
c onnec ts to 110-typ e c ross c onnec t bloc ks.
nNever use quad  c ab le (untwisted  two pair telep hone c ab le) in a 
DS1 line.
nAvoid  mixing  wires of d ifferent g aug es in a DS1 line.
6. If using  external alarm eq uip ment, attac h the sup p lied  DW8 c ab le to the 
120A and  the external eq uip ment. The maximum length of this c ab le 
d ep end s on the alarm eq uip ment. 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-54 Installing an Integrated Channel Service Unit (ICSU) Module 
4
7. If a TN474F is used , make sure the c irc uit p ac k is set for 24-c hannel 
op eration. Set the switc h on the c irc uit p ac k as shown in Fig ure 2-1.
8. From the DS1 c irc uit-p ac k form of the system ad ministration c onsole, set 
the line c omp ensation field  to 0-133 ft (40.6 m).
9. Reset the 120A b y reseating  the DS1 c irc uit p ac k.
When you reinsert the DS1 c irc uit p ac k after installing  a 120A CSU the 
120A resets. The DS1 c irc uit p ac k initializes and  tests the 120A. When  
initialization and  testing  is c omp lete, the g reen LED goes off. If the RED 
indic ator is OFF after the test, the ICSU is working .
10. If the c irc uits d o not p ass the self test, troub leshoot the 120A as instruc ted  
in Integ rated  CSU Mod ule Installation and  Op eration, 555-230-193.
Table 4-8
 p rovid es the H700-383 c ab le pinouts. Table 4-9 p rovides the c ab le 
leng ths for eac h c ab le g roup  numb er.
Table 4-8. H700-383 Cable Pin Assignments
Pin ColorChannel Service 
Unit DesignationNetwork 
Designation Function
1BK Line in 0 R1 RCV
2 Y Line in 1 T1
3 Shield
4 R Line out 0 R XMT
5 G Line out 1 T
7 Shield
7 Not assigned
8 Not assigned
Table 4-9. H700-383 Cable Lengths by Group Number
Group Length Group Length
1 25 feet (7.7 m) 5 125 ft (38.1 m)
2 50 feet (15.2 m) 7 200 ft (71 m)
3 75 feet (22.9 m) 7 400 ft (122 m)
4 100 feet (30.5 m) 8 750 ft (198.1 m) 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-55 Add NAA1 Fiber Optic Circuit Pack 
4
Add NAA1 Fiber Optic Circuit Pack
Unpack and Inspect
1. Verify the eq uipment rec eived . See Figure 4-12. Ac tual eq uip ment may 
vary in ap p earanc e and  may ship  in sep arate p ac kag es.
2. See Table 4-10
 for a list of p art c omc od es.
Figure 4-12. NAA1 Fiber Optic Interface Kit Equipment Figure Notes
1. NAA1 c irc uit p ac k
2. SC/ST c onnec tors (2x)
3. SC/SC c onnec tors (2x)4. Fiber cables (2 gray multi-mode 
c ab les for use with the TN2305 
c irc uit p ac k and 2 yellow sing le 
mod e c ables for use with the TN2306 
circuit pack)
ckdakit LJK 021199
A
B
A B
A B
A BA B
1
2
3
4 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-56 Add NAA1 Fiber Optic Circuit Pack 
4
Installation Instructions
1. Remove the c over. 
2. Insert the ATM c irc uit p ac k, p referab ly in the top  row.
3. Insert the c onnec tor into the top  op ening  at the rear of the NAA1 c irc uit 
pack. See Figure 4-13
.
4. Attac h either the sing le mod e (yellow) c able or multi-mod e (g ray) c ab le to 
the c onnec tor.
5. Route the c ab le throug h the slot A in the fac ep late.
6. Determine how muc h of the c ab le is need ed  to reac h the ATM c irc uit 
pack.
7. Wrap  the exc ess c ab le as shown in Figure 4-13
 and  sec ure with the c lip s.
8. If using two ATM circuit pac ks, repeat steps 2 - 7. 
NOTE:
In Step  3, use the b ottom op ening  at the rear of the NAA1 c irc uit 
pack. 
In Step  5, use slot B in the fac ep late. 
In Step  7, use the lower set of c lip s to sec ure the exc ess c able.
9. Insert the NAA1 c irc uit p ac k into slot 11 on the top  row of the c omp ac t 
modular cabinet.
!CAUTION:
Do not attemp t to p ut this c irc uit p ac k into any other slot; p in d amag e 
may occur.
Table 4-10. Parts List
Quantity Description Comcode
1 Fiber op tic  interfac e kit
Kit inc lud es: NAA1 c irc uit p ac k, 2 SC/SC 
c onnec tors, 2 SC/ST c onnec tors, and  4 c ables 
(2 for sing le mod e and  2 for multi-mod e).108424391 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-57 Add NAA1 Fiber Optic Circuit Pack 
4
10. Route the c ab le(s) to the ATM c irc uit p ac k(s) and  c onnec t them.
NOTE:
The loop  formed  b y the c ab le c onnec ting  the two c irc uit pac ks must 
have a minimum rad ius of 1”  (2.54 c m). If not, ad just the c ab le or 
move the ATM c irc uit p ac k to another loc ation. 
11. Connec t the other eq uip ment into the c onnec tor(s) at the rear of the NAA1 
circuit pack.
12. Rep lac e the c over.
Figure 4-13. NAA1 Circuit Pack with Cables Attached
A
B
A
B
ckdanaa1 LJK 021199
A
B
A B
A B 
						

							DEFINITY ECS Release 8.2 Installation, Upgrades, 
and Additions for Compact Modular Cabinets  555-233-118  Issue 1
April 2000
Adding or Removing Hardware 
4-58 Add NAA1 Fiber Optic Circuit Pack 
4
Test the Installation of the ATM Circuit Pack
1. Log  into the manag ement terminal.
2. Ad minister the system b y referring  to ATM Installation, Up g rad es, and  
Ad ministration, 555-233-106.
3. Type list configuration all
 and  p ress 
En t e r to determine if the new ATM 
c irc uit p ac k ap p ears in the c orrec t slot and that there are no c irc uit p ac k 
c onflic ts. The NAA1 c irc uit pac k will not be id entified  in the list.