HP Z5200 Owners Manual
Have a look at the manual HP Z5200 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2.Begin lifting the Formatter from the printer. Push the clips and provide upward force at the same time. 3.Lift the Formatter out of the printer. NOTE: When you install a new formatter follow the instructions provided on the Flyer that accompanies it to set up the printer. Hard Disk Drive Removal and installation 1.Remove the Formatter on page 296. 2. Unscrew four screws in the formatter. ENWW Hard Disk Drive 297
3.Remove the hard disk drive from the formatter by applying force in the direction of the arrow. 4.Insert a new hard disk drive. NOTE: If you try to insert a previously used hard disk drive, the printer displays a System Error and will not start successfully. 5. Replace all screws that you removed earlier. Electronics Module (Main PCA and PSU) Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Left Cover (refer Left Cover on page 188). 2. Disconnect all the connectors on the Electronics Module. 298 Chapter 6 Removal and Installation ENWW
3.Unroute all the cables disconnected in the previous step. 4.Remove two T-15 screws that secure the Electronics Module to the Printer. 5.Remove one T-15 screw that secures the Electronics Module to the Printer. ENWW Electronics Module (Main PCA and PSU) 299
6.Remove one T-15 screw that secures the Electronics Module to the Printer. 7.Remove two T-15 screws that secure the Electronics Module to the Printer. 8.Remove one T-15 screw that secures the Electronics Module to the printer. 300 Chapter 6 Removal and Installation ENWW
9.Carefully lift the Electronic s Module out of the printer. NOTE:When you install the Electronics Module make sure it is correctly aligned with the mounting rail. NOTE: When you finish installing or replacing this component, yo u must perform the necessary Service Calibrations. To find which calibrations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170 . Starwheel Assembly Removal NOTE: Switch off the printer and remove the power cable. 1.Open the Window. ENWW Starwheel Assembly 301
2.Remove one T-15 screw that secures the Starwheel Assembly to the Printer. 3.Remove one T-15 screw that secures the Starwheel Assembly to the Printer. 4.Carefully lift the Starwheel A ssembly out of the printer. NOTE:When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Print Zone Overdrive Removal 302 Chapter 6 Removal and Installation ENWW
NOTE:Switch off the printer and remove the power cable. 1.Remove the Starwheel Assembly (refer Starwheel Assembly on page 301). NOTE: The Print Zone Overdrive is in two sections (left and right). This procedure describes the removal of both of the sections. If you only want to remove one of the sections skip the steps for the other section. 2. Remove one T-15 screw that secures the left clamp of the Print Zone Overdrive to the Platen. 3.Lift the attachment clamp vertically to release it from the Platen. 4.Remove the clamp. ENWW Print Zone Overdrive 303
5.Repeat steps 2 to 4 to remove the remaining five attachment clamps. 6.Use a flat bladed screwdriv er to unclip the left Print Zone Over drive retaining clip and rotate the clip vertically. 7. Carefully lift the left Print Zone Overdrive enough 10 mm) so you can slide it to the left. 304 Chapter 6 Removal and Installation ENWW
8.Slide the left Print Zone Overdrive to the left disengage the center coupling. 9.Carefully left Prin t Zone Overdrive out of the printer. 10.Remove the center coupling. ENWW Print Zone Overdrive 305
11.Use a flat bladed screwdriv er to unclip the left Print Zone Over drive retaining clip and rotate the clip vertically. 12. Carefully lift the right Print Zone Overdrive out of the printer. NOTE:When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Left Spittoon Removal This procedure describes how to remove the complete Left Spittoon which is necessary to gain access to other components. If you only need to replace the Foams of the Left Spittoon, use the protective gloves and the tweezers (provided in the Tool Kit) to remove them with it in place. NOTE: Switch off the printer and remove the power cable. 1.Remove the Left Cover (refer Left Cover on page 188). 2. Remove the Electronics Module (Main PCA and PSU) (refer Electronics Module (Main PCA and PSU) on page 298). 306 Chapter 6 Removal and Installation ENWW