HP Z5200 Owners Manual

							2.The Front Panel  will show the 7. IDS submenu.
3.In the IDS submenu, scroll to  Ink Delivery System  and press OK to start the test.
4. The Ink Delivery System test starts and the fron t Panel prompts you to remove all the Ink Supplies.
5.Remove all the Ink Cartridges.
6. Press  OK to continue.
7. The test continues and the front Panel displays the following messages:
● Starting Horsburgh.
● Starting Mips.
● Starting Nvm.
● Getting Part Number.
● Starting ISS Motors.
● Moving Bongos down.
● Reading Bongos down.
● Moving Bongos up.
● Reading Bongos up.
● Starting OutOfInk sensors.
● Reading OutOfInk.
8. The Front Panel then prompts you push down Bongo0. 9
9.Press and hold down Bongo0 which is located at the furthest left Ink Cartridge position.
10. Press any key.
ENWW Service Tests (Diagnostics) 107 
						

							11.Release Bongo0.
12. Press any key.
13. The Front Panel then displays the Bongo0 test results.
14.Press any key to continue.
15. Repeat steps 8 through 14 for the remaining Out of Ink sensors for each of the Ink Cartridges.
16. The front Panel prompts you to insert all the Ink Supplies.
17.Install all the Ink Cartridges.
18. Press  OK to continue.
19. The Acumen Supplies test and the front Panel displays the following messages:
●Starting AcumenSupplies.
● Reading AcumenSupplies.
20. The Front Panel then displays Acumen Supplies test results.
21.The Front Panel shows the test co mplete display for a few seconds.
108 Chapter 3   Diagnostic Menu ENWW 
						

							22.The Front Panel prompts you to shutdown the printer to complete the test.
23.Press any key to shutdown the printer.
Check Ink Supplies
1. In the Diagnostics menu, scroll to 7. IDS  and press OK.
2. The Front Panel will show the7. IDS  submenu.
3.In the  IDS submenu, scroll to Check Ink Supplies  and press OK to start the test.
4. The Check Ink Supplies test starts and the  front Panel displays the following messages:
● Starting Horburgh & Mips.
● Starting Nvm.
● Getting Part Number.
● Starting Supplies.
● Starting AcumenSupplies.
● Reading Ink Supplies.
5. The Front Panel then displays C heck Ink Supplies test results.
6.Press any key to continue.
ENWW Service Tests (Diagnostics) 109 
						

							7.The Front Panel shows the test co mplete display for a few seconds.
8.The Front Panel prompts you to shutdown  the printer to complete the test.
9.Press any key to shutdown the printer.
Check Leakage
1. In the Diagnostics menu, scroll to  7. IDS and press OK.
2. The Front Panel will show the7. IDS submenu.
3.In the  IDS submenu, scroll to Leakage and press  OK to start the test.
4. The Check Ink Leakage test checks that ther e is no ink in the tubes or ink cartridge
8. Service Station
The complete Service Station test consists of individual tests for the different components related to this
subsystem.
These tests are:
●Service Station
● Primer Motor
● Aerosol Fan
110 Chapter 3   Diagnostic Menu ENWW 
						

							Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components, check the Service Calibration Guide to Removal
and Installation to see which tests and calibrations you need to perform. Refer to 
Service Calibration
Guide to Removal and Installation on page 170 .
Service Station
1. In the Diagnostics menu, scroll to 8. Service Station and press  OK.
2. The Front Panel will show the8. Service Station  submenu.
3.In the  8. Service Station  submenu, scroll to  Service Station and press OK to start the test.
4. The Service Station test starts and the front Panel displays the following messages:
● Starting Horsburgh.
● Booting up Carriage.
● Starting SVS Motor.
● Starting Nvm.
● Getting Part Number.
● Starting Service Station.
● Starting Scan Axis.
● Moving SVS out of Sax.
● Homing Scan Axis.
● Moving Carriage out of SVS.
● Homing Service Station.
● Moving to Spit Rear pos.
● Moving to Spit Front pos.
● Moving to Wipe forward pos.
● Moving to Wipe reverse pos.
● Moving to Cleaner pos.
● Moving to Color Sensor (ESP) pos.
ENWW Service Tests (Diagnostics) 111 
						

							●Homing Scan Axis.
● Starting ServicingServices.
● Capping Service Station.
● Uncapping Service Station.
● Starting Mechanical Init.
5. The Front Panel then prompts you to  check the status of the printer.
6.Check that:
●The Window is closed.
● The Media Lever is lowered.
● All Printheads are inserted.
● Valid Cartridges are inserted.
7. Press  OK to continue.
8. The Front Panel then displays test results.
9.Press any key to finish the test.
10. The Front Panel shows the test co mplete display for a few seconds.
112 Chapter 3   Diagnostic Menu ENWW 
						

							11.The Front Panel prompts you to shutdown the printer to complete the test.
12.Press any key to shutdown the printer.
Primer Motor
1. In the Diagnostics menu, scroll to 8. Service Stationand press  OK .
2. The Front Panel  will show the 8. Service Station  submenu.
3.In the  8. Service Station  submenu, scroll to  Primer Motor and press OK to start the test.
4. The Primer Motor test starts and the fr ont Panel displays the following messages:
● Starting TestsGpio.
● Starting Horsburgh.
● Booting up Carriage.
● Starting SVS Motor.
● Starting Nvm.
● Getting Part Number.
● Starting Service Station.
● Starting Scan Axis.
● Moving SVS out of Sax.
● Homing Scan Axis.
● Moving Carriage out of SVS.
● Homing Service Station.
● Moving to Spit Rear pos.
ENWW Service Tests (Diagnostics) 113 
						

							●Moving to Spit Front pos.
● Moving to Wipe forward pos.
● Moving to Wipe reverse pos.
● Moving to Cleaner pos.
● Moving to Color Sensor (ESP) pos.
● Homing Scan Axis.
● Starting ServicingServices.
● Capping Service Station.
● Uncapping Service Station.
● Starting Mechanical Init.
5. The Front Panel then prompts you to  check the status of the printer.
6.Check that:
●The Window is closed.
● The Media Lever is lowered.
● All Printheads are inserted.
● Valid Cartridges are inserted.
7. Press  OK to continue.
8. The Primer Motor test continues and the Fr ont Panel shows the progress of the test.
9.The Front Panel shows the test co mplete display for a few seconds.
114 Chapter 3   Diagnostic Menu ENWW 
						

							10.The Front Panel prompts you to shutdown the printer to complete the test.
11.Press any key to shutdown the printer.
Aerosol Fan
1. In the Diagnostics menu, scroll to 8. Service Station and press  OK.
2. The Front Panel will show the8. Service Station  submenu.
3.In the 8. Service Station submenu, scroll to  Aerosol Fan and press OK to start the test.
4. The Aerosol Fan test starts and the fr ont Panel displays the following messages:
● Starting Horsburgh.
● Booting TestsGpio.
● Starting Nvm.
5. The front Panel then prompts you switch on the Aerosol Fan.
6.Press  OK to switch on the Aerosol Fan. If you do not wish to switch on the Aerosol Fan use the
Arrow  keys to select NO  and press OK.
ENWW Service Tests (Diagnostics) 115 
						

							7.The test continues and the Front Panel displays the results.
8.Press any key to continue.
9. The front panel prompts you to check if the Aerosol Fan is operating.
10.Listen carefully to check if the Aerosol Fan is operating.
11. If it is operating, use the  Arrow keys to select  YES and press  OK . If it is NOT operating, select
NO  and press  OK .
12. The Front Panel shows the test result.
13.Press any key to finish.
14. The Front Panel shows the test co mplete display for a few seconds.
15.The Front Panel prompts you to shutdown  the printer to complete the test.
16.Press any key to shutdown the printer.
116 Chapter 3   Diagnostic Menu ENWW