HP Z5200 Owners Manual
Have a look at the manual HP Z5200 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
▲When installing the new belt, make sure the belt is correctly installed under the carriage assembly. Scan-Axis Motor Removal NOTE:Switch off the printer and remove the power cable. 1.Remove the Right Cover (refer Right Cover on page 185). 2. Remove the Left Cover (refer Left Cover on page 188). 3. Loosen the T-10 uncapping scre w sufficiently so you can manually move the Carriage Assembly in step 4. 4. Push the Carriage Assembly into the print path. ENWW Scan-Axis Motor 257
5.Loosen the T-15 screw Belt Tensioner to the printer to remove the tension from the belt. 6.Leave the Belt Tensioner in place. NOTE: There is a spacer between the right end plate and the tensioner. 7.Remove the Belt Assembly from the drive wheel of the Scan-Axis Motor. 258 Chapter 6 Removal and Installation ENWW
8.Remove three T-15 screws that secure the Scan-Axis Motor to the printer. 9.Unroute the Scan-Axis Motor supply cable from the cable clamp. 10.Disconnect the Scan-Axis Motor supply connector from PrintMech PCA. ENWW Scan-Axis Motor 259
11.Remove three T-15 screws that secure the Scan-Axis Motor to the printer. 12.Carefully pull the Scan-Axis Motor out of the printer (10 mm) until you can rotate it approximately 30 degrees counterclockwise. 13.Remove the Scan-Axis Motor from the printer. NOTE: When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Carriage Rail Oiler Removal NOTE:Switch off the printer and remove the power cable. 1.Remove the Right Cover (refer Right Cover on page 185). 260 Chapter 6 Removal and Installation ENWW
2.Remove the T-15 Carriage Rail Oiler attachment screw. 3.Remove the Carriage Rail Oiler from the printer. NOTE:When you reinstall the Carriage Rail Oiler, use the Oil and Oil Dispenser from the Lubrication Kit to add 2-3 drops of oil to the foam of the Carriage Rail Oiler and in the small depression of the Carriage Rear Bushing. ENWW Carriage Rail Oiler 261
4.Add 2 or 3 drops of oil in the depression where the Slider fits. Color Sensor (ESP) Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Right Cover (refer Right Cover on page 185). 2. Remove the Left Cover (refer Left Cover on page 188). 3. Remove the Front Panel (refer Front Panel on page 203). 4. Remove the Top Cover (refer Top Cover on page 205). 5. Remove the Window Position Sensor (refer Window Position Sensor on page 208). 6. Remove the Ink Supply Tubes Support Rail (refer Ink Supply Tubes Support Rail on page 209). 7. Open the Carriage Cover. 262 Chapter 6 Removal and Installation ENWW
8.Remove all the Printheads. 9.Remove the four T-15 screws that secure the Ink Supply Tubes to the Carriage Assembly. 10.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time. ENWW Color Sensor (ESP) 263
11.Close and lock the Carriage Cover. 12.Carefully move the Ink Supply Tubes into the print path. 13.Unclip and slide off the small cover of the Carriage Assembly Carriage PCA. 264 Chapter 6 Removal and Installation ENWW
14.Remove one T-15 screws that secures the large cover of the Carriage PCA. 15.Remove the large cover of the Carriage PCA. 16.Disconnect the Color Sensor (ESP) electr ical connection from the Carriage PCA. ENWW Color Sensor (ESP) 265
17.Remove one T-10 screw that secures the Colo r Sensor (ESP) to the Carriage Assembly. 18.Loosen the T-10 uncapping screw sufficiently so you can manually move the Carriage Assembly in step 26. 19. Push the Carriage Assembly into the print path enough to allow access to the Color Sensor (ESP). 266 Chapter 6 Removal and Installation ENWW