HP Z5200 Owners Manual

							11.Unclip the clip to release the  Service Station from the printer.
12.Lower the Service Station from the printer.
13.Lower the right of the Service Station enough to allow you to slide it carefully out of the printer.
NOTE: When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170 .
Drop Detector
Removal
ENWW Drop Detector 217 
						

							NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Remove the Service Station (refer 
Service Station on page 214).
3. Unroute the Drop Detector ribbon cable  from the Service Station cable clamps.
4.Remove the T-15 screw that secures the Drop Detector to the Service Station.
5.Lift the Drop Detector off the Service Station.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
218 Chapter 6   Removal and Installation ENWW 
						

							Aerosol Fan Assembly
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Disconnect the Aerosol Fan Assembly inline connector.
3.Remove the four T-15 screws that secure the  Aerosol Fan Assembly to the Service Station.
NOTE:The four access holes in the  Aerosol Fan Assembly housing are the same size as the
attachment screw diameter so you will need a norm al Torx Screwdriver, not a multi-tool, to remove
the screws.
ENWW Aerosol Fan Assembly 219 
						

							4.Remove the Aerosol Fan Assembly from the Service Station.
NOTE: When you reinstall the Aerosol Fan Assembly ma ke sure you position it so that the power
cable is on the outside exiting to the right.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
PrintMech PCA
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Disconnect all the electrical co nnectors from the PrintMech PCA.
220 Chapter 6   Removal and Installation ENWW 
						

							3.Remove the grounding cable attachment screw from the PrintMech PCA.
4.Remove the three T-15 screws that secure  the PrintMech PCA to the Service Station.
5.Remove the PrintMech PCA from the printer.
NOTE: When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170 .
Pen to Paper Space (PPS) Solenoid
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
ENWW Pen to Paper Space (PPS) Solenoid 221 
						

							2.Unroute the Pen to Paper Space (PPS) Solenoid cable from the cable clamp.
3.Disconnect the Pen to Paper Space (PPS) Solenoid connector from the PrintMech PCA.
4.Remove two T-15 screws  that secure the Pen to Paper Space (PPS) Solenoid to the printer.
222 Chapter 6   Removal and Installation ENWW 
						

							5.Remove the Pen to Paper Space  (PPS) Solenoid from the printer.
NOTE:When you finish installing or  replacing this component, yo u must perform the necessary
Service Calibrations. To find which calibrations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170 .
Spindle
Removal
NOTE: Switch off the printer and remove the power cable.
1.Pull the left end of the Spindle (viewed from the fr ont of the printer) out of the Left Spindle Holder.
2.Lift the Spindle out of the printer towards t he left (viewed from the front of the printer).
ENWW Spindle 223 
						

							Left Spindle Holder
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Spindle (refer to Spindle on page 223).
2. Remove two T-15 screws that secure the Left Spindle Holder to the printer.
3.Rotate the Left Spindle  Holder towards the left.
4.Remove the Left Spindle Holder from the printer.
Right Spindle Holder
Removal
224 Chapter 6   Removal and Installation ENWW 
						

							NOTE:Switch off the printer and remove the power cable.
1.Remove the Spindle (refer to Spindle on page 223).
2. Remove two T-15 screws that secure the Right Spindle Holder to the printer.
3.Rotate the Right Spindle Holder towards the right.
4.Remove the Right Spindle Holder from the printer.
Clean Out Assembly
Removal
NOTE: Switch off the printer and remove the power cable.
1.Remove the Spindle (refer to Spindle on page 223).
ENWW Clean Out Assembly 225 
						

							2.Disconnect the Out Of Paper Sensor in-line connector and unroute its cable.
3.Remove the four T-15 screws that secure Clean Out Assembly to the printer.
4.Beginning with the  left side, slide the Clean Out Assembly out of the printer. Double check that the
Out Of Paper Sensor on the left side of the Clean Out Assembly has not been damaged.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
Out Of Paper Sensor
Removal
226 Chapter 6   Removal and Installation ENWW