HP Z5200 Owners Manual
Have a look at the manual HP Z5200 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
7.Open the Carriage Cover. 8.Remove all the Printheads. 9.Remove the four T-15 screws that secure the Ink Supply Tubes to the Carriage Assembly. ENWW Carriage PCA 277
10.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time. 11.Close and lock the Carriage Cover. 12.Carefully move the Ink Supply Tubes into the print path. 278 Chapter 6 Removal and Installation ENWW
13.Unclip and slide off the small cover of the Carriage Assembly Carriage PCA. 14.Remove one T-15 screws that secures the large cover of the Carriage PCA. 15.Remove the large cover of the Carriage PCA. ENWW Carriage PCA 279
16.Disconnect the ten ribbon cables from the Carriage Assembly PCB. 17.Press the locking clip to release the Carriage Assembly PCB from the carriage. 18.Remove the Carriage PCA from the carriage. NOTE: When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Right Ink Supply Station Removal NOTE:Switch off the printer and remove the power cable. 1.Remove the Right Cover (refer Right Cover on page 185). 280 Chapter 6 Removal and Installation ENWW
2.Remove two T-10 screws that secure the Right Side Plate of the Ink Supply Station. 3.Remove the Right Side Plate of the Right Ink Supply Station. 4.Remove two T-10 screws that secure the Left Side Plate of the Right Ink Supply Station. ENWW Right Ink Supply Station 281
5.Remove the Right Ink Supply Station bonding cable. 6.Remove the Right Side Plate of the Right Ink Supply Station. 7.Remove the T-15 screw that secures the Right Ink Supply Station to the printer. 282 Chapter 6 Removal and Installation ENWW
8.Remove the two T-15 screws that secure th e Right Ink Supply Station to the printer. 9.Disconnect the three connectors from the Right Ink Supply Station. NOTE: If you need to change the ISS Harness Cable, make sure you keep the previously used plastic connector. The new cable will arrive with a female end, which you will replace with the existing male end. 10. Unroute the three cables from the Right Ink Supply Station. ENWW Right Ink Supply Station 283
11.Carefully lift the Cartridge Tubes Connecto r out of the Right Ink Supply Station. 12.Carefully lift the Right Ink Supply Station enough so that you can rotate it clockwise to release the front attachment from the printer. 13. Carefully lift the Right Ink Supply St ation completely out of the printer. NOTE:When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Left Ink Supply Station Removal NOTE:Switch off the printer and remove the power cable. 1.Remove the Left Cover (refer Left Cover on page 188). 284 Chapter 6 Removal and Installation ENWW
2.Remove two T-10 screws that secure the Left Side Plate of the Left Ink Supply Station. 3.Remove the Left Side Plates of the Left Ink Supply Station. 4.Remove two T-10 screws that secure the Right Side Plate of the Left Ink Supply Station. ENWW Left Ink Supply Station 285
5.Remove the Left Ink Supply Station bonding cable. 6.Remove the Right Side Plate of the Left Ink Supply Station. 7.Remove the T-15 screw that secures the Left Ink Supply Station to the printer. 286 Chapter 6 Removal and Installation ENWW