HP Z5200 Owners Manual
Have a look at the manual HP Z5200 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
8.Remove the two T-15 screws th at secure the Left Ink Supply Station to the printer. 9.Disconnect the three connectors from the Left Ink Supply Station. NOTE: If you need to change the ISS Harness Cable, make sure you keep the previously used plastic connector. The new cable will arrive with a female end, which you will replace with the existing male end. 10. Unroute the three cables from the Left Ink Supply Station. ENWW Left Ink Supply Station 287
11.Carefully lift the Cartridge Tubes Connector out of the Left Ink Supply Station. 12.Carefully lift the Left Ink Supply Station enough so that you can rotate it counterclockwise to release the front attachment from the printer. 13.Carefully lift the Left Ink Supply Station completely out of the printer. NOTE: When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Ink Supply Tubes Removal 288 Chapter 6 Removal and Installation ENWW
NOTE:Switch off the printer and remove the power cable. 1.Remove the Right Cover (refer Right Cover on page 185). 2. Remove the Left Cover (refer Left Cover on page 188). 3. Remove the Front Panel (refer Front Panel on page 203). 4. Remove the Top Cover (refer Top Cover on page 205). 5. Open the Carriage Cover. 6.Remove all the Printheads. 7.Remove the four T-15 screws that secure the Ink Supply Tubes to the Carriage Assembly. ENWW Ink Supply Tubes 289
8.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time. 9.Close and lock the Carriage Assembly cover. 10.Carefully feed the Ink Supply Tubes into the print path area. 290 Chapter 6 Removal and Installation ENWW
11.Remove the top T-15 screw that secures Ink Supply Tubes guide to the printer. 12.Remove the two front T-15 screws that secu re Ink Supply Tubes guide to the printer. 13.Carefully lift the Ink Supply Tubes guide enough until you can slide it forwards out of the printer. ENWW Ink Supply Tubes 291
14.Gently move the Ink Supply Tubes from the printer. 15.Use a flat bladed screwdriver to release all the Ink Supply Tubes clamps from the printer. 16.Remove two T-10 screws that secure the right Side Plate of the Right Ink Supply Station. 292 Chapter 6 Removal and Installation ENWW
17.Remove the Right Side Plate of the Right Ink Supply Station. 18.Remove two T-10 screws that secure the left Side Plate of the Right Ink Supply Station. 19.Remove the Right Ink Supply Station bonding cable. ENWW Ink Supply Tubes 293
20.Remove the left Side Plate of the Right Ink Supply Station. 21.Carefully lift the Cartridge Tubes Connecto r out of the Right Ink Supply Station. 22.Remove two T-10 screws that secure the left Side Plate of the Left Ink Supply Station. 294 Chapter 6 Removal and Installation ENWW
23.Remove the left Side Plate of the Left Ink Supply Station. 24.Remove two T-10 screws that secure the right Side Plate of the Left Ink Supply Station. 25.Remove the Left Ink Supply Station bonding cable. ENWW Ink Supply Tubes 295
26.Remove the right Side Plate of the Left Ink Supply Station. 27.Carefully lift the Ink Supply Tubes out of the printer. NOTE:When you finish installing or replacing this component, you must perform the necessary Service Calibrations. To find which ca librations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170. Formatter Removal NOTE:Switch off the printer and remove the power cable. 1.Fully loosen the two locking thumbscrews that secure the Formatter in the printer. 296 Chapter 6 Removal and Installation ENWW