HP Z5200 Owners Manual
Have a look at the manual HP Z5200 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4.Unclip the spring from the attachment points on the Media Lever and Left Cover. 5.Remove three T-15 screws that secure the Media Lever. 6.Lift the Media Lever of the mounting. ENWW Media Lever 197
7.Remove the Media Lever from the printer. Media Lever Position Sensor Removal NOTE: Switch off the printer and remove the power cable. 1.Raise the Media Lever. 2. Remove the Left Cover (refer Left Cover on page 188). 3. Disconnect the Media Lever Position Sensor. 4.Remove one T-15 screw that secures the Media Lever Position Sensor to the Scan Side Panel. 198 Chapter 6 Removal and Installation ENWW
5.Rotate the Media Lever Position Sensor vertically to disengage the attachment lug from the Scan Side Panel. 6.Remove the Media Lever Position Sensor. NOTE: When you finish installing or replacing this component, yo u must perform the necessary Service Calibrations. To find which calibrations you must perform, refer to Service Calibration Guide to Removal and Installation on page 170 . Cutter Assembly Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Left Cover Finishing Panel (refer to step 3 for the removal procedure of the Left Cover on page 188). ENWW Cutter Assembly 199
2.Fully loosen the cutter rail end cap attachment screw. 3.Remove the cutter rail end cap. 4.Slide the Cutter Assembly out of the printer. NOTE: When you install the new Cutter Assembly, fo llow the installation instructions provided with the new Cutter Assembly. Right Rear Tray Support Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Rear Tray (refer Rear Tray on page 194). 2. Remove the Right Cover (refer Right Cover on page 185). 200 Chapter 6 Removal and Installation ENWW
3.Remove the Left Cover (refer Left Cover on page 188). 4. Remove the Rear Cover (refer Rear Cover on page 195). 5. Remove two T-15 screws that secure the Right Rear Tray Support to the printer. 6.Rotate the Right Rear Tray Support counterclockwise approximately 30 degrees. 7.Remove the Right Rear Tray Support from the printer. Left Rear Tray Support Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Rear Tray (refer Rear Tray on page 194). 2. Remove the Right Cover (refer Right Cover on page 185). ENWW Left Rear Tray Support 201
3.Remove the Left Cover (refer Left Cover on page 188). 4. Remove the Rear Cover (refer Rear Cover on page 195). 5. Remove two T-15 screws that secure the Left Rear Tray Support to the printer. 6.Rotate the Left Rear Tray Support clockwise approximately 30 degrees. 7.Remove the Left Rear Tray Support from the printer. 202 Chapter 6 Removal and Installation ENWW
Front Panel Removal NOTE:Switch off the printer and remove the power cable. 1.Open the Window. 2.With strong pressure, squeeze the top edge of the front panel enough to release the attachment clips, and begin rotating the Front Panel vertically in the next step. 3.Rotate the front panel vertically. ENWW Front Panel 203
4.Disconnect the interface cable from the Front Panel. 5.Push in the clip that prevents the Ferrite Core from being removed. 6.Slide the Ferrite Core out of the brackets. 204 Chapter 6 Removal and Installation ENWW
7.Remove the Front Panel. NOTE: When you reinstall the Front Panel, you must ma ke sure that the Ferrite Core is correctly positioned. The Ferrite Core is necessary to avoid electrostatic interference being generated. NOTE: When you finish installing or replacing this component, yo u must perform the necessary Service Calibrations. To find which calibrations you must perform, Refer to Service Calibration Guide to Removal and Installation on page 170. Top Cover Removal NOTE: Switch off the printer and remove the power cable. 1.Remove the Window (refer Window on page 174). 2. Remove the Right Cover (refer Right Cover on page 185). 3. Remove the Left Cover (refer Left Cover on page 188). 4. Remove the Rear Tray (refer Rear Tray on page 194). 5. Remove the Rear Cover (refer Rear Cover on page 195). 6. Remove the Front Panel (refer Front Panel on page 203). 7. Remove the four T-15 top screws that secure the Top Cover to the printer. ENWW Top Cover 205
8.Remove the front T-15 screw that secures the front left side of the Top Cover to the printer. 9.Carefully pull the attachment clip forward until you can lift the bottom left corner of the Top Cover approximately 10 mm. 10. Remove the front T-15 screw that secures the front left side of the Top Cover to the printer. 206 Chapter 6 Removal and Installation ENWW