HP Z5200 Owners Manual

							2.When the following message appears on the front  panel, you must select whether you would like
to continue with the calibration by pressing the  OK key. Press Back or Cancel  to exit the calibration.
3.If media is not loaded, the following message ap pears on the front panel. Load media in to the
Printer and start again from  step 1.
Before continuing,  the Printer will check the following:
● The Media Lever is in the lowered position.
● The correct paper type is loaded
 (check list on previous page).
● The correct paper size (minimum paper size 24 inches).
If these conditions are  not met, a warning will be displayed on the Front Panel and you will need
to restart the Calibration from  step 1.
NOTE: Make sure you keep your  hands away from the Print Platen  as the Carriage will be moving
at high speed and you could injure your self or damage the Carriage Assembly.
4.The printer will start to calibrate the Line Sensor . Once the Line Sensor has been calibrated, the
results will be displayed on the Front Panel. Press  OKto continue or press  Back or Cancel  to exit
the calibration.
If the values are not within the range specified, an erro r will appear on the Front Panel. In this case,
try the following:
● Try the Scan-Axis Calibration again.
● Replace the Line Sensor
ENWW Service Calibrations 147 
						

							5.The Printer will start to calibrate the Line Sensor  position to the Black Printhead. The printer will
print a line of black dots and then scan them:
6. Once the Line Sensor has been calibrated, the results will be displayed on the Front Panel. If the
values are within the range, press  OK to accept the results. If the values are NOT within the range,
press  Back or Cancel  to exit and FAIL the calibration. Once the Line Sensor has been calibrated,
the results will be displaye d on the Front Panel. Press  OK to finish the calibration or press  Back
or  Cancel  to exit the calibration.
7.The Printer will now perform the Printhead Alignment. When the following message appears on
the front panel, you must select whether you would  like to continue with the calibration by pressing
the  OK key. Press  Back or Cancel  to exit the calibration.
8.Once the Printhead Alignment is  completed, the following message  will be displayed on the Front
Panel. Press the  OK key to continue.
If the Printhead Alignment fails  for any reason, a warning message will appear  on the Front Panel.
In this case, try the following:
● Enter the Front Panel menu and retry the Printhead Alignment. If the Alignment completes
successfully, then perfor
m the Color Calibration.
● If the Alignment fails again, check the Alignment pattern to see if any of the Printheads are
printing incorrectly. If necessary, perform a 
Printhead Recovery through the Front Panel and
retry the Printhead Alignment.
148 Chapter 4   Service Menu ENWW 
						

							9.If the Alignment fails again, check the Alignment pa ttern to see if any of the Printheads are printing
incorrectly. If necessary, perform a Printhead  Recovery through the Front Panel and retry the
Printhead Alignment.
Carriage PCA
The purpose of this Service Calibration is to reset the ink short thresholds after replacing the Carriage
PCA. This calibration  is integrated into the Scan  Axis diagnostic test. See 
4. Carriage Assembly
on page 95.
Perform the Carriage Setup as follows:
1. In the Service Calibrations submenu, scroll to Carriage PCA and press  OK.
2. To calibrate the Carriage  PCA, run the Carriage Assembly diagnostic test. See 4. Carriage
Assembly on page 95.
Color Sensor (ESP) Calibration
The purpose of this Service Calibration is to  calibrate the Color Sensor (Color Sensor (ESP).
Service calibrations also need to be performed after  removing or replacing certain printer components.
If you have removed or replaced printer components , check the Service Calibration Guide to Removal
and Installation to see which tests and calibrations you need to perform. Refer to 
Service Calibration
Guide to Removal and Installation on page 170 .
Perform the Color Sensor (ESP) Calibration as follows:
1. In the Service Calibrations submenu, scroll  to Color Sensor (ESP) Calibration and press  OK.
ENWW Service Calibrations 149 
						

							2.When the following message appears on the fron t panel, you must select whether you would like
to continue with the Carriage Setup by pressing  OK. Press  Back or  Cancel to exit the utility.
3.The printer will start to ca librate the Color Sensor:
Once the Color Sensor calibration has completed successfully,  OK will be displayed on the Front
Panel.
150 Chapter 4   Service Menu ENWW 
						

							5 Parts and Diagrams
●Printer Support on page 152
●
Center Covers (Front) on page 153
●
Center Covers (Rear) on page 154
●
Right Cover on page 155
●
Left Cover on page 156
●
Right Hand Assemblies on page 157
●
Left Hand Assemblies on page 158
●
Carriage Assembly on page 159
●
Scan-Axis Assemblies on page 160
●
Paper Path Asse mblies (Front) on page 161
●
Paper Path Assemblies (Rear) on page 162
●
Tools 1 on page 163
●
Tools 2 on page 164
●
Miscellaneous Parts on page 165
ENWW 151 
						

							Printer Support
Reference onFigureHP Part NumberPart DescriptionPagea
1Q5669-60718Leg CoverN/A
2Q5669-60716Legs AssemblyN/A
3Q5669-60715Foot Assembly (includes 1 foot and 1 support
tube)N/A
4Q6659–60237Bin assembly (incl udes the Bin Support)N/A
5Q5669–60236X-BraceN/A
7Q5669-60715Foot Bracket (part of Foot Assembly)N/A
6–&–8 Q5669-67063 Tube Basket & Rear Basket Bracket (Includes
screws for Legs Assembly) N/A
152 Chapter 5   Parts and Diagrams
ENWW 
						

							Center Covers (Front)
Reference on FigureHP Part NumberPart DescriptionPagea
1CH538–67030WindowWindowon page 174
2CQ113–67002Top cover
3CH538-67071Window Position Sensor (with
shield)Window Position
Sensor
on page 208
4Q6659–60089Anti-ESD Media Output
AssemblyMedia OutputAssembly
on page 178
5Q6659–60165Front coverFront Coveron page 177
6Q6675-60060Front PanelFront Panel
on page 203
ENWW Center Covers (Front) 153 
						

							Center Covers (Rear)
Reference on FigureHP Part NumberPart DescriptionPagea
1Q5669-60660Rear Tray SupportsRight Rear Tray Supporton page 200
2Q6687–67801Clean Out AssemblyClean Out Assembly
on page 225
3Q5669–67801Out Of Paper SensorOut Of Paper Sensor
on page 226
4Q6659–60170Rear TrayRear Tray on page 194
5Q6659–60164Rear coverRear Cover on page 195
154 Chapter 5   Parts and Diagrams ENWW 
						

							Right Cover
Reference on FigureHP Part NumberPart DescriptionPagea
1CQ113–67005Right CoverRight Cover on page 185
2Q6675–60109Integrated front TrimRight Front Trim on page 179
3CQ113–67015Right Ink Cartridge DoorRight Ink Cartridge Door
on page 182
ENWW Right Cover 155 
						

							Left Cover
Reference on FigureHP Part NumberPart DescriptionPagea
1CQ113–67006Left Ink Cartridge DoorLeft Ink Cartridge Dooron page 183
2Q6675–60109Left Front Trim/Right Front Trim
(Right not shown)Left Front Trim
on page 181
3CQ113–67007Left Side PanelLeft Cover on page 188
4CQ113–67004 Left CoverLeft Cover on page 188
156 Chapter 5   Parts and Diagrams ENWW