HP Z5200 Owners Manual

							11.The Carriage Assembly UVC flag test starts and the Front Panel displays:
● Clearing UVC flag.
● Reading UVC flag.
● Checking UVC flag.
12. The Front Panel then displays  the UVC flag test results.
13.Press any key to continue.
14. The Carriage Assembly Pens Voltage test  starts and the Front Panel displays:
● Getting Vpp.
15. The Front Panel then displays the Pens Volt age test results. The result must be between 26.5 and
33 Volts .
16.If the results are correct, press  OK to accept the results. If th e results are not correct, press  Back
  Cancel  to reject the results and FAIL the test.
17. The Carriage Assembly test continues and the Front Panel displays:
● Starting Line Sensor Leds.
● Starting Light Sensor.
● Starting Line Sensor.
System Error Code 55:YZ
. Refer 
55:YZ on page 62.
● Starting SVS Motor.
● Starting Carriage Motor.
● Moving SVS out of Sax.
● Moving Carriage middle.
● Initializing LineSensor.
ENWW Service Tests (Diagnostics) 97 
						

							18.The Front Panel then prompts you to load roll media.
19.Load roll media.
NOTE: For the LED test to work properly, the paper must be loaded completely through the
carriage path.
20. Press any key to continue.
21. The Carriage Assembly test continues and the Front  Panel displays the result of each phase of the
test:
● Setting LS low intensity.
For each color LED: Blue, Green, Red, and Amber
● Setting LS max intensity.
For each color LED: Blue, Green, Red, and Amber
● Checking Tolerance.
● Starting NvmLineSensor.
● Initializing NvmLineSensor.
● Getting LS Serial Number.
● Reading LS Nvm.
● Writing new LS Nvm.
● Checking LS Serial Number.
● Starting Service Station.
● Starting Scan Axis.
● Moving SVS out of sax.
● Homing Scan Axis.
● Moving Carriage out of SVS.
● Homing Service Station.
● Starting Servicing Services.
● Starting ColorSensor.
98 Chapter 3   Diagnostic Menu ENWW 
						

							22.The Front Panel then prompts you  to enable the Color Sensor (ESP).
23.Press  OK to the enable the Color Sensor (ESP). If you do not wish to en able the Color Sensor
(ESP) use the Arrow  keys to select NO and press  OK.
24. The Color Sensor (ESP)  enable test starts and the front  Panel displays the following messages:
● Starting ColorSensor.
● Starting ColorSensing.
● Reading Color Sensor (ESP) status.
● Enabling Color 
Sensor (ESP).
25. The Front Panel then displays Color Sensor (ESP) e nable test result and prompts you to press any
key to continue.
26. Press any key to continue.
27. The Front Panel then prompts yo u to confirm the information.
28.Press  OK to the confirm the information. If you want to reject the information use the Arrow keys
to select  NO and press  OK.
29. The Carriage Assembly  calibration test starts and the front Panel displays the following messages:
● Starting ColorSensor.
● Starting ColorSensing.
● Reading Color Sensor (ESP) status.
● Reading registers.
● Performing calibration.
ENWW Service Tests (Diagnostics) 99 
						

							30.The Front Panel then displays DeltaE test result and prompts you to press any key to continue.
31.Press any key to continue.
32. The Carriage moves into the print path and the front Panel then prompts you to remove all pens.
33.Open the Window.
34. Open the Carriage cover.
35. Remove all the Printheads from the Carriage.
36. Press any key to continue.
37. The Carriage Assembly pens test ex ecutes and checks the pens status.
38. The Front Panel then prompts you  to replace all the Printheads.
39.Replace all the Printheads.
40. Close the Carriage Cover.
41. Close the Window.
42. Press any key to continue.
43. The Carriage Assembly pens test cont inues and checks the pens status.
44. The Front Panel then displays the test result.
45.Press any key to continue.
100 Chapter 3   Diagnostic Menu ENWW 
						

							46.The Encoder Manager test starts and the Front Panel  displays the result of each phase of the test.
47. The Front Panel then displays Encoder Difference (Lef t/Right) test result and prompts you to press
any key to finish.
48. Press any key to finish.
49. The Front Panel shows the test co mplete display for a few seconds.
50.The Front Panel prompts you to shutdown the printer to complete the test.
51.Press any key to shutdown the printer.
5. Sensors
The Sensors test diagnoses Failures of any sensors of the printer. Always run this test before replacing
any of the following sensors:
●Window sensor.
● Media Lever position sensor.
● Media sensor.
Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components,  check the Service Calibration Guide to Removal
and Installation to see which tests and calibrations you need to perform, refer to 
Service Calibration
Guide to Removal and Installation on page 170 .
1. In the Diagnostics menu, scroll to 5. Sensors  and press OK.
ENWW Service Tests (Diagnostics) 101 
						

							2.The Sensors test starts and the Front Panel pr ompts you to verify default sensor positions:
3.Verify that the sensors are in the default positions and any key to continue.
4. The Window sensor test starts and the Fr ont Panel prompts you to open the Window:
5.Open the Window.
6. Press any key to continue.
7. The Window sensor test continues and the Front Panel prompts you to close the Window:
8.Close the Window.
9. Press any key to continue.
10. The Media Lever sensor test starts and the Front Panel prompts you to raise the Media Lever:
11.Raise the Media Lever.
12. Press any key to continue
102 Chapter 3   Diagnostic Menu ENWW 
						

							13.The Media Lever sensor test continues and the Front Panel prompts you to lower the Media Lever:
14.Lower the Media Lever.
15. Press any key to continue.
16. The Media sensor test starts and the Front Panel prompts you load media:
17.Raise the Media Lever.
18. Load media.
19. Lower the Media Lever.
20. Press any key to continue.
21. The Media sensor test continues and t he Front Panel prompts to remove media:
22.Raise the Media Lever.
23. Unload the media.
24. Lower the Media Lever.
25. Press any key to continue.
26. The Front Panel shows the test co mplete display for a few seconds.
ENWW Service Tests (Diagnostics) 103 
						

							27.The Front Panel prompts you to shutdown  the printer to complete the test.
28.Press any key to shutdown the printer.
6. Color Sensor (ESP)
The Color Sensor (ESP) test diagnoses Failures of the Color Sens or located on the carriage. Always
run this test before replacing the Color sensor.
Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components, check the Service Calibration Guide to Removal
and Installation to see which tests and calib rations you need to perform. Refer to 
Service Calibration
Guide to Removal and Installation on page 170.
1. In the Diagnostics menu, scroll to  6. Color Sensor (ESP) and press OK.
2. The Color Sensor (ESP) test starts and the  front Panel displays the following messages:
● Starting Horburgh.
● Starting Carriage.
● Starting Nvm.
● Getting Part Number.
● Getting Scan Axis size.
● Starting Service Station.
● Starting Scan Axis.
● Moving SVS out of Sax.
● Homing Scan Axis.
● Moving Carriage out of SVS.
● Homing Service Station.
● Starting Servicing Services.
● Capping Service Station.
● Starting ColorSensor.
104 Chapter 3   Diagnostic Menu ENWW 
						

							3.The Front Panel then prompts you  to enable the Color Sensor (ESP).
4.Press  OK to the enable the Color Sensor (ESP). If you do not wish to en able the Color Sensor
(ESP) use the Arrow  keys to select NO and press  OK.
5. The Color Sensor (ESP)  enable test starts and the front  Panel displays the following messages:
● Starting ColorSensor.
● Starting ColorSensing.
● Reading Color Sensor (ESP) status.
● Enabling Color 
Sensor (ESP).
6. The Front Panel then displays Color Sensor (ESP) e nable test result and prompts you to press any
key to continue.
7. Press any key to continue.
8. The Front Panel then displays th e Color Sensor (ESP) details and prompts you to press any key
to continue.
9. The Front Panel then prompts you load media:
10.Raise the Media Lever.
11. Load media.
12. Lower the Media Lever.
ENWW Service Tests (Diagnostics) 105 
						

							13.Press any key to continue.
14. The Front Panel then displays the DeltaE test resu lt and prompts you to press any key to continue.
15.Press any key to continue.
16. The Front Panel shows the test co mplete display for a few seconds.
17.The Front Panel prompts you to shutdown  the printer to complete the test.
18.Press any key to shutdown the printer.
7. Ink Delivery System (IDS)
The complete Ink Delivery System test  consists of individual tests for the different components related
to this subsystem. These tests are:
● Ink Delivery System
● Check Ink Supplies
Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components, check the Service Calibration Guide to Removal
and Installation to see which tests and calib rations you need to perform. Refer to 
Service Calibration
Guide to Removal and Installation on page 170.
Ink Delivery System
1. In the Diagnostics menu, scroll to  7. IDS and press  OK.
106 Chapter 3   Diagnostic Menu ENWW