Dell 1355cn User Guide

							Dell Printer Configuration Web Tool169
Security 
SettingsEncryptionSelect the security method from the list.
No Security
*Specifies No Security to 
configure the wireless setting 
without specifying a security 
method from WEP, WPA-
PSK AES/WPA2-PSK AES, 
and WPA-PSK TKIP.
WEP 64 Bit 
ASCII (5 Bytes)Specifies the WEP 64 Bit 
ASCII to use through the 
wireless network.
WEP 128 Bit 
ASCII (13 Bytes)Specifies the WEP 128 Bit 
ASCII to use through the 
wireless network.
WEP 64 Bit Hex 
(10 Bytes)Specifies the WEP 64 Bit Hex 
to use through the wireless 
network.
WEP 128 Bit Hex 
(26 Bytes)Specifies the WEP 128 Bit 
Hex to use through the 
wireless network.
WPA-PSK AES
*1Specifies the WPA-PSK AES 
to use through the wireless 
network.
WPA2-PSK AES
*1Specifies the WPA2-PSK AES 
to use through the wireless 
network.
WPA-PSK TKIPSpecifies the WPA-PSK TKIP 
to use through the wireless 
network. 
WEP Key 1Enter the WEP key when WEP is selected from 
Encryption.
Re-enter WEP Key 1Enter the WEP key 1 again to confirm.
WEP Key 2Enter the WEP key when WEP is selected from 
Encryption.
Re-enter WEP Key 2Enter the WEP key 2 again to confirm.
WEP Key 3Enter the WEP key when WEP is selected from 
Encryption.
Re-enter WEP Key 3Enter the WEP key 3 again to confirm.
 
						

							170Dell Printer Configuration Web Tool
 NOTE: This item is available only when the printer is connected with a wireless 
network.
TCP/IP
Purpose:
To configure the IP address, subnet mask, and gateway address of the printer. 
Va l u e s :WEP Key 4Enter the WEP key when WEP is selected from 
Encryption.
Re-enter WEP Key 4Enter the WEP key 4 again to confirm.
Tr a n s m i t  K e ySpecifies the transmit key type from the list.
Pass PhraseSpecifies the pass phrase.
Re-enter Pass PhraseEnter the pass phrase again to confirm.
*1This item is available only when the Infrastructure mode is selected for Network 
Ty p e .
 
						

							Dell Printer Configuration Web Tool171
TCP/IP 
SettingsHost NameSpecifies the host name.
IP ModeSpecifies the IP mode.
IPv4 IP Address ModeSelects the IP address mode.
Manual IP 
AddressManually sets the IP address.
Manual Subnet 
MaskManually sets the subnet 
mask.
Manual Gateway 
AddressManually sets the gateway 
address.
IPv6 Use Manual 
AddressTo set the IP address 
manually.
Manual AddressManually sets the IP address. 
To specify an IPv6 address, 
enter the address followed by 
a slash (/) and then 64. For 
details, consult your system 
administrator.
Stateless Address 
1-3Displays the stateless 
addresses.
Link Local 
AddressDisplays the link local address.
Manual Gateway 
AddressManually sets the gateway 
address.
Auto Configure 
Gateway AddressDisplays the gateway address.
 
						

							172Dell Printer Configuration Web Tool
DNS DNS Domain 
NameSpecifies the domain name of the domain name 
server. Up to 255 alphanumeric characters, 
periods, and hyphens can be used. If you need to 
specify more than one domain name, separate 
them using a comma or semicolon.
IPv4 Get DNS Server 
Address from 
DHCPSpecifies whether to get the 
DNS server address 
automatically from the 
DHCP server.
Manual DNS 
Server AddressSets the DNS server address.
IPv6 Get DNS Server 
Address from 
DHCPv6-liteSpecifies whether to get the 
DNS server address 
automatically from the 
DHCPv6-lite server.
Manual DNS 
Server AddressSets the DNS server address.
LPD Connection 
Time-OutSets the connection time-out period from 1 to 
1000 seconds.
Port9100 Port NumberSets the port number from 9000 to 9999.
Connection 
Time-OutSets the connection time-out period between 1 
and 1000 seconds.
HTTP Port Number Sets the port number. This must be 80 or between 
8000 and 9999.
Simultaneous 
ConnectionsDisplays the maximum number of connections 
received simultaneously by the client.
Connection 
Time-OutSets the connection time-out period from 1 to 255 
seconds.
 
						

							Dell Printer Configuration Web Tool173
E-Mail Alert
Purpose:
To configure settings for E-Mail Alert. This page can also be displayed by 
clicking 
E-Mail Alert in the left frame.
Va l u e s :WSD Port NumberSets the port number. This must be 80 or between 
8000 and 9999.
Receive 
Ti me-OutSets the receive time-out period from 1 to 65535 
seconds.
Notification 
Delivery Time-
OutSets the notification time-out period from 1 to 60 
seconds.
Maximum 
Number of TTLSets the maximum number of TTL from 1 to 10.
Maximum 
Number of 
NotificationSets the maximum number of notifications from 
10 to 20.
 
						

							174Dell Printer Configuration Web Tool
E-Mail Server 
SettingsPrimary SMTP 
GatewaySets the primary SMTP gateway.
SMTP Port 
NumberSpecifies the SMTP port number. This must be 
25, 587 or between 5000 and 65535.
E-Mail Send 
AuthenticationSpecifies the authentication method for outgoing 
e-mail.
SMTP Login 
UserSpecifies the SMTP login user. Up to 63 
alphanumeric characters, periods, hyphens, 
underscores, and at symbols (@) can be used. If 
specifying more than one address, separate them 
using commas.
SMTP Login 
Pa s s w o r dSpecifies the SMTP account password using up to 
31 alphanumeric characters.
Re-enter SMTP 
Login PasswordEnter the SMTP account password again to 
confirm.
POP3 Server 
AddressSpecifies the POP3 server address in IP address 
format of aaa.bbb.ccc.ddd or as a DNS host 
name using up to 63 characters.
POP3 Port 
NumberSpecifies the POP3 server port number. This must 
be 110 or between 5000 and 65535.
POP User 
NameSpecifies the POP3 account user name. Up to 63 
alphanumeric characters, periods, hyphens, 
underscores, and at symbols (@) can be used. If 
specifying more than one address, separate them 
using commas.
POP User 
Pa s s w o r dSpecifies the POP3 account password using up to 
31 alphanumeric characters.
Re-enter POP 
User PasswordEnter the password again to confirm.
Reply AddressDesignates the reply e-mail address sent with each 
E-mail Alert.
SMTP Server 
ConnectionDisplays the status of the SMTP server 
connection.
 
						

							Dell Printer Configuration Web Tool175
SNMP
Purpose:
To configure the detailed settings of SNMP.
Va l u e s :E-Mail Alert 
SettingsE-Mail List 1Sets acceptable e-mail addresses for the E-Mail 
Alert feature using up to 255 alphanumeric 
characters.
Select Alerts for 
List 1Supplies AlertsSpecifies whether to receive an 
e-mail alert for consumables.
Paper Handling 
AlertsSpecifies whether to receive an 
e-mail alert for paper handling.
Service CallSpecifies whether to receive an 
e-mail alert for service calls.
E-Mail List 2Sets acceptable e-mail addresses for the E-Mail 
Alert feature using up to 255 alphanumeric 
characters.
Select Alerts for 
List 2Supplies AlertsSpecifies whether to receive an 
e-mail alert for consumables.
Paper Handling 
AlertsSpecifies whether to receive an 
e-mail alert for paper handling.
Service CallSpecifies whether to receive an 
e-mail alert for service calls.
 
						

							176Dell Printer Configuration Web Tool
Community 
NameCommunity 
Name 
(Read only)Specifies the community name to access (read 
only) data using up to 31 alphanumeric 
characters.
The original setting will remain valid if nothing is 
entered. Characters entered for community name 
in the previous settings will not be displayed on 
the screen. The default Read Community is 
public.
Re-enter 
Community 
Name (Read only)Enter the community name to access (read only) 
data again to confirm.
Community 
Name 
(Read/Write)Specifies the community name to access (read 
and write) data using up to 31 alphanumeric 
characters.
The original setting will remain valid if nothing is 
entered. Characters entered for community name 
in the previous settings will not be displayed on 
the screen. The default Read/Write Community 
is private.
Re-enter 
Community 
Name 
(Read/Write)Enter the community name to access (read and 
write) data again to confirm.
Community 
Name (Trap)Specifies the community name used for trap up 
to 31 alphanumeric characters. 
The original settings will remain valid if nothing 
is entered. Characters entered for community 
name in the previous settings will not be 
displayed on the screen. The default Trap 
Community is   (NULL).
Re-enter 
Community 
Name (Trap)Enter the community name used for trap again to 
confirm.
 
						

							Dell Printer Configuration Web Tool177
Scan to PC
Purpose:
To specify the client when scanning data.
Va l u e s :Tr a p  
Notification 
1-4Trap Address TypeSelect the trap address type from the list. 
Selecting Off clears the settings in Trap Address, 
Po r t  N u m b e r, and Notify, and does not notify 
trap occurrence. Selecting IPv4 or IPv6 allows 
you to enter Trap Address.
Trap AddressSpecifies the IP address and IP socket in the 
following format:
•IPv4
Specifies the IP address and IP socket in the 
nnn.nnn.nnn.nnn:mmmmm format. Each 
section of nnn is a variable value between 0 
and 255. Note that values 127 and 224-254 are 
not valid for the first three-digits only. IP socket 
mmmmm is a variable value between 0 and 
65535.
•IPv6
Specifies the IP address and IP socket in the 
xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:mmm
mm format. Each section of xxxx is a 
hexadecimal variable value between 0 and ffff. 
IP socket mmmmm is a variable value between 0 
and 65535.
Trap Notification 
(IP) Port NumberEnter the SNMP trap destination port number.
NotifySpecifies whether to notify trap occurrence. 
Authenticate Error TrapSpecifies whether to notify Authenticate Error 
Tr a p .
FTP Client Connection 
Ti me-OutSets the connection time-out period from 1 to 60 
seconds.
FTP PassiveSets whether to enable the FTP Passive mode.
 
						

							178Dell Printer Configuration Web Tool
Other Features
The Other Features tab contains the Set Password and Reset Print Server pages.
Set Password
Purpose:
To set or change the password that is required to access the setup parameters 
of the printer from the 
Dell Printer Configuration Web Tool.
This page can also be displayed by clicking 
Set Password in the left frame.
Va l u e s :
 
NOTE: If you forgot your password, initialize NVM (non-volatile memory) to restore 
the password to the default (NULL). See Reset Print Server on page 178.
 
NOTE: When you change the password to lock the operator panel, set the 
password from Panel Lock Set in the Printer Settings.
Reset Print Server
Purpose:
To initialize NVM (non-volatile memory) for the network feature and reboot 
the printer. You can also initialize the NVM of the printer from Reset 
Defaults in the Printer Settings menu.
Va l u e s :SMB Client Connection 
Time-OutSets the connection time-out period from 1 to 60 
seconds.
Administrator 
PasswordSets the password using up to 10 alphanumeric characters. The 
password will appear as asterisks (*) in the field when it is entered.
Re-enter 
Administrator 
PasswordEnter the password again to confirm.
Initialize NIC 
NVRAM 
Memory and 
restart printer.Click the Start button to initialize NVM. Network settings will 
revert to the factory default settings and reboot the network 
capability.