Cisco 6500e Manual

							1-49
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Generic Installation Procedures
Figure 1-25 Installing the Shelf Brackets
Figure 1-26 Attaching the Crossbar Bracket to the Shelf Brackets
H9466
Shelf bracket Shelf bracket
12-24 x 3/4-inch
or
10-32 x 3/4-inch screw (6x)
48123
Shelf bracket
Shelf bracket
M3 screw
M3 screw Crossbar
bracketFront of rack 
						

							1-50
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Generic Installation Procedures
Installing the Rubber Feet Kit
This section describes how to install the rubber feet kit. The kit contains four rubber feet and mounting 
screws. The rubber feet attach directly to the bottom of the chassis and support the weight of the chassis. 
The rubber feet kit is shipped as part of the Catalyst 6500 series switch accessory kit with the following 
chassis:
Catalyst 6506-E
Catalyst 6509-E
To install the rubber feet kit, perform the following steps:
Step 1Tilt the chassis to one side to access the bottom of the chassis.
Step 2Position one of the rubber feet over the threaded hole on the bottom corner of the chassis. 
Step 3Secure the rubber foot to the chassis with one of the M5 x 12 mm Phillips screws provided in the 
installation kit.
Step 4Repeat step 1 through step 3 to install the remaining three rubber feet in the bottom corners of the 
chassis.
Step 5Position the chassis upright so that it rests on the four rubber feet.
Installing the Stabilizer Bracket Kit 
The stabilizer bracket kit is included as part of the accessory kits for the following chassis:
Catalyst 6509-NEB switch
Catalyst 6513 switch and Catalyst 6513-E switch
If you are not installing the Catalyst 6509-NEB, Catalyst 6513, or Catalyst 6513-E switch in a rack, you 
must install stabilizer brackets to the bottom of the chassis. The stabilizer brackets reduce the possibility 
that the freestanding switch chassis will tip over. 
Ta b l e 1 - 4 lists and describes the contents of the rack-mount shelf kit.
NoteYou will need the assistance of a second person to perform this installation.
Table 1-4 Stabilizer Kit Contents
Quantity Part Description
16 M4 Phillips-head countersunk screws used to 
secure the stabilizer brackets to the chassis
2 Stabilizer brackets 
						

							1-51
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Generic Installation Procedures
To install the stabilizer brackets, follow these steps:
Step 1Have one person tilt and hold the chassis to one side.
Step 2With the chassis slightly tilted, attach the stabilizer bracket to the side of the chassis with the eight M4 
screws, as shown in Figure 1-27.
Step 3Tilt the chassis to the other side.
Step 4Attach the second stabilizer bracket to the other side of the chassis with eight M4 screws.
Step 5Lower the chassis so that it rests on both stabilizer brackets.
Figure 1-27 Installing the Stabilizer Brackets
NoteIf you are not rack-mounting the Catalyst 6513 or the Catalyst 6513-E switch chassis and you want to 
install the optional cable guide assemblies, you must obtain ten 12-24 or 10-32 nuts. Use the screws 
supplied in the accessory kit and the nuts you obtained to attach the cable guide assembly to the 
L bracket.
FA N
STATUS
8 PORT GIGABIT ETHERNETWS-X64081LIN
KSTATUS2
34
5
6
7
8L
IN
KL
IN
KLIN
KLIN
KLIN
KLIN
KL
IN
K8 PORT GIGABIT ETHERNETWS-X64081L
IN
KSTATUS2
34
5
6
7
8LIN
KLIN
KLIN
KL
IN
KL
IN
KLIN
KL
IN
K8 PORT GIGABIT ETHERNETWS-X64081L
IN
KSTATUS2
34
5
6
7
8LIN
KL
IN
KLIN
KL
IN
KL
IN
KL
IN
KL
IN
K
2
4
 P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
1LINK2LINK3LINK4LINK5LINK6LINK7LINK8LINK9LINK1
0LINK1
1LINK1
2LINK1
3LINK1
4LINK1
5LINK1
6LINK1
7LINK1
8LINK1
9LINK2
0LINK2
1LINK2
2LINK2
3LINK2
4LINK1L
I
N
K2L
I
N
K3L
I
N
K4L
I
N
K5L
I
N
K6L
I
N
K7L
I
N
K8L
I
N
K9L
I
N
K1
0L
I
N
K1
1L
I
N
K1
2L
I
N
K1
3L
I
N
K1
4L
I
N
K1
5L
I
N
K1
6L
I
N
K1
7L
I
N
K1
8L
I
N
K1
9L
I
N
K2
0L
I
N
K2
1L
I
N
K2
2L
I
N
K2
3L
I
N
K2
4L
I
N
K1L
I
N
K2L
I
N
K3L
I
N
K4L
I
N
K5L
I
N
K6L
I
N
K7L
I
N
K8L
I
N
K9L
I
N
K10L
I
N
K11L
I
N
K12L
I
N
K13L
I
N
K14L
I
N
K15L
I
N
K16L
I
N
K17L
I
N
K18L
I
N
K19L
I
N
K20L
I
N
K21L
I
N
K22L
I
N
K23L
I
N
K24L
IN
K1L
I
N
K2L
I
N
K3L
I
N
K4L
I
N
K5L
IN
K6L
IN
K7L
I
N
K8L
I
N
K9L
I
N
K1
0L
I
N
K1
1L
I
N
K1
2L
I
N
K1
3L
I
N
K1
4L
I
N
K1
5L
I
N
K1
6L
I
N
K1
7L
IN
K1
8L
IN
K1
9L
I
N
K2
0L
IN
K2
1L
I
N
K2
2L
I
N
K2
3L
I
N
K2
4L
IN
K
SUPERVISOR2 WS-X6K-SUP2-2GESTATUSSYSTEMCONSOLEPWR MGMTRESETCONSOLECONSOLE
PORT
MODEPCMCIAEJECTPORT 1PORT 2Switch    Load   
100%
1%LINK
LINKSUPERVISOR2 WS-X6K-SUP2-2GESTATUSSYSTEMCONSOLEPWR MGMTRESETCONSOLECONSOLE
PORT
MODEPCMCIAEJECTPORT 1PORT 2Switch    Load   
100%
1%LINK
LINK
1
2
3
4
5
6
7
8
9
10
11
12
13
48126 
						

							1-52
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Establishing the System Ground 
This section describes how to connect a system ground to the Catalyst 6500 series switches. 
NoteThis system ground is also referred to as the network equipment building system (NEBS) ground. 
CautionInstallations that rely solely on system grounding using only an AC third-prong ground run a 
substantially greater risk of equipment problems and data corruption than those installations that use 
both the AC third-prong ground and a properly installed system (NEBS compliant) ground.
The system (NEBS) ground provides additional grounding for EMI shielding requirements and 
grounding for the low voltage supplies (DC-DC converters) on the modules and is intended to satisfy the 
Telcordia Technologies NEBS requirements for supplemental bonding and grounding connections. You 
must observe the following system grounding guidelines for your chassis:
You must install the system (NEBS) ground connection with any other rack or system power ground 
connections that you make. The system (NEBS) ground connection is required if FXS modules are 
installed or if this equipment is installed in a U.S. or European Central Office.
You must connect both the system (NEBS) ground connection and the power supply ground 
connection to an earth ground. The system (NEBS) ground connection is required if FXS modules 
are installed or if this equipment is installed in a U.S. or European Central Office.
For Catalyst 6503 or Catalyst 6503-E chassis that are equipped with DC-input power supplies, you 
must install the system (NEBS) ground before you attach the source DC power cables to the DC 
PEM. If the Catalyst 6503 or Catalyst 6503-E chassis is powered up, you must power down the 
chassis before attaching the system (NEBS) ground. If you are installing the system (NEBS) ground 
on other models of the Catalyst 6500 series chassis that are equipped with either AC-input or 
DC-input power supplies, you do not need to power down the chassis.
If you are installing the 8700 W AC-input power supply on a Catalyst 6506, Catalyst 6509, or on a 
Catalyst 6509-NEB chassis, you must install the system ground (NEBS ground) on the power supply 
rather than on the switch chassis. The extended depth of the 8700 W power supply blocks access to 
the system ground pad on those chassis. There are two ground posts located on the power supply 
faceplate where the system ground connection can be made.
NoteIn all situations, grounding practices must comply with Section 250 of the National Electric Code (NEC) 
requirements or local laws and regulations. A 6 AWG grounding wire is preferred from the chassis to the 
rack ground or directly to the common bonding network (CBN). The equipment rack should also be 
connected to the CBN with 6 AWG grounding wire.
NoteThe system (NEBS) ground serves as the primary safety ground for the Catalyst 6503 and 
Catalyst 6503-E chassis that are equipped with DC-input power supplies. The DC-input power supplies 
for these chassis do not have a separate ground. 
						

							1-53
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Required Tools and Equipment
To connect the system ground, you need the following tools and materials:
Grounding lug—A two-hole standard barrel lug. Supports up to 6 AWG wire. Supplied as part of 
accessory kit.
Grounding screws—Two M4 x 8 mm (metric) pan-head screws. Supplied as part of the accessory 
kit.
Grounding wire—Not supplied as part of accessory kit. The grounding wire should be sized 
according to local and national installation requirements. Depending on the power supply and 
system, a 12 AWG to 6 AWG copper conductor is required for U.S. installations. Commercially 
available 6 AWG wire is recommended. The length of the grounding wire depends on the proximity 
of the switch to proper grounding facilities. 
No. 1 Phillips screwdriver.
Crimping tool to crimp the grounding wire to the grounding lug.
Wire-stripping tool to remove the insulation from the grounding wire.
Connecting the System Ground
To attach the grounding lug and cable to the grounding pad, follow these steps:
Step 1Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of 
the grounding wire.
Step 2Insert the stripped end of the grounding wire into the open end of the grounding lug. 
Step 3Crimp the grounding wire in the barrel of the grounding lug. Verify that the ground wire is securely 
attached to the ground lug.
Step 4Locate and remove the adhesive label from the system grounding pad on the switch. The location of the 
system grounding pad differs among Catalyst 6500 series chassis. 
Refer to these figures to locate the system grounding pad on your chassis:
Catalyst 6503 and Catalyst 6503-E chassis—Figure 1-28
CautionThe system (NEBS) ground serves as the primary safety ground for the Catalyst 6503 and 
Catalyst 6503-E chassis that are equipped with DC-input power supplies. You must install the system 
(NEBS) ground before you attach the source DC power cables to the DC PEM. If the Catalyst 6503 or 
Catalyst 6503-E chassis are already powered up, we recommend that you remove the source DC from 
the Catalyst 6503 and Catalyst 6503-E chassis before attaching the system (NEBS) ground. 
Catalyst 6504-E chassis—Figure 1-29
Catalyst 6506, Catalyst 6509, and Catalyst 6509-NEB chassis—Figure 1-30
Catalyst 6506-E, Catalyst 6509-E, Catalyst 6513, and Catalyst 6513-E chassis—Figure 1-31
Catalyst 6509-NEB-A and Catalyst 6509-V-E chassis—Figure 1-32 
						

							1-54
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Step 5Place the grounding wire lug against the grounding pad, making sure that there is solid metal-to-metal 
contact.
NoteThere are two system grounding pads on the Catalyst 6509-NEB-A and the Catalyst 6509-V-E 
switch chassis. One pad is located in the upper-left corner of the chassis, and the other is located 
in the upper-right corner of the chassis. Additionally, both system grounding pads have 3 M4 
screw holes so that the system grounding lug can be installed either horizontally or vertically.
Step 6Secure the grounding lug to the chassis with two M4 screws. Ensure that the grounding lug and the 
grounding wire will not interfere with other switch hardware or rack equipment.
Step 7Prepare the other end of the grounding wire, and connect it to an appropriate grounding point in your 
site to ensure adequate earth ground for the switch.
Figure 1-28 System Ground Location (Catalyst 6503 and Catalyst 6503-E Chassis)
SUPERVISOR2 WS-X6K-SUP2-2GESTATUSSYSTEMCONSOLEPWR MGMTRESETC
O
N
S
O
LEC
O
N
S
O
LE
P
O
R
T
M
O
D
EP
C
M
C
IAE
JE
C
TP
O
R
T 1P
O
R
T
 2S
w
itch    Loa
d   
10
0%
1%
LINK
LINKO
S
M
-4
O
C
1
2
 P
O
S
-S
I
4
 P
O
R
T
 O
C
-1
2
 P
O
S
 S
M
 IRS
T
A
T
U
S
1
1 2
23
3 4
4R
E
S
E
T L
I
N
K
L
I
N
KL
I
N
K
L
I
N
K
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
1 R
X
A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
2 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
3 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
4 R
X
O
S
M
-
4
O
C
1
2
 P
O
S
-S
I
4
 P
O
R
T
 O
C
-
1
2
 P
O
S
 S
M
 IR
S
T
A
T
U
S
1
1 2
23
3 4
4R
E
S
E
T L
I
N
K
L
I
N
KL
IN
K
L
I
N
K
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
1 R
X
A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
2 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 3 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
4 R
X
63190
System ground
connector System ground
connector
Grounding lug
Wire 
						

							1-55
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Figure 1-29 System Ground Location (Catalyst 6504-E Chassis)
130891
STATUS
FA N
STATUS
STATUS
STATUS
System ground
connectorSystem ground
connector
Grounding lugWire 
						

							1-56
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Figure 1-30 System Ground Location (Catalyst 6506, Catalyst 6509, and Catalyst 6509-NEB 
Chassis)
32672INPUT
OKFA N
OKOUTPUT
FA I L
o
INPUT
OKFA N
OKOUTPUT
FA I L
o
1
2
3
4
5
6
8
 P
O
R
T
 G
I
G
A
B
IT
 E
T
H
E
R
N
E
TWS-X64081LINKSTATUS2
3
4
56
7
8LINKLINKLINKLINKLINKLINKLINK8
 P
O
R
T
 G
IG
A
B
IT
 E
T
H
E
R
N
E
TWS-X64081LINKSTATUS2
3
4
5
6
7
8LINKLINKLINKLINKLINKLINKLINK24 PORT 100FXW
S
-X
62
24STATUS1LIN
K2LINK3LIN
K4LINK5LIN
K6LINK7LINK8LIN
K9LIN
K10LIN
K11LIN
K12LIN
K13LIN
K14LIN
K15LIN
K16LIN
K17LIN
K18LIN
K19LIN
K20LINK21LINK22LIN
K23L
IN
K24LIN
K24 PORT 100FXW
S
-
X
6
2
2
4S
T
A
T
U
S1LIN
K2LIN
K3L
INK4L
IN
K5LIN
K6LIN
K7LIN
K8L
IN
K9LIN
K10L
IN
K11LINK12LIN
K13L
IN
K14LIN
K15LIN
K16LIN
K17L
INK18LINK19L
IN
K20LINK21LIN
K22LINK23LIN
K24L
IN
K
Grounding
pad Grounding
pad location
under lip 
Grounding lug Wire
Screws (M4)
FA N
STATUS
S
U
P
E
R
V
IS
O
R
2 W
S
-X
6
K
-S
U
P
2
-2
G
ES
T
A
T
U
SS
Y
S
T
E
MC
O
N
S
O
L
EP
W
R
 
M
G
M
TR
E
S
E
TC
O
N
S
O
L
EC
O
N
S
O
L
E
P
O
R
T
M
O
D
EP
C
M
C
I
AE
J
E
C
TP
O
R
T
 
1P
O
R
T
 
2S
w
i
t
c
h
 
 
 
 
L
o
a
d
 
 
 
1
0
0
%
1
%
LINK
LINKS
U
P
E
R
V
IS
O
R
2 W
S
-X
6K
-S
U
P
2-2G
ES
T
A
T
U
SS
Y
S
T
E
MC
O
N
S
O
L
EP
W
R
 
M
G
M
TR
E
S
E
TC
O
N
S
O
L
EC
O
N
S
O
L
E
P
O
R
T
M
O
D
EP
C
M
C
IAE
J
E
C
TP
O
R
T
 1P
O
R
T
 
2S
w
i
t
c
h
 
 
 
 
L
o
a
d
 
 
 
1
0
0
%
1
%
LINK
LINK 
						

							1-57
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Figure 1-31 System Ground Location (Catalyst 6506-E, Catalyst 6509-E, Catalyst 6513, and 
Catalyst 6513-E Chassis)
FA N
STATUS
8 PORT GIGABIT ETHERNETWS-X64081LINKSTATUS2
3
4
5
6
7
8LIN
KLIN
KL
IN
KL
IN
KLIN
KLIN
KLIN
K8 PORT GIGA
BIT ETHERNETWS-X64081LIN
KSTATUS2
3
4
56
7
8LIN
KL
INKL
IN
KLIN
KLIN
KLIN
KL
IN
K8 PORT GIGABIT ETHERNETWS-X64081L
IN
KSTATUS2
34
5
6
7
8LINKLINKLIN
KLIN
KL
IN
KLIN
KLIN
K
2
4
 
P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 
P
O
R
T
 1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 
P
O
R
T
 
1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
2
4
 P
O
R
T
 1
0
0
F
XW
S
-
X
6
2
2
4S
T
A
T
U
S
1LINK2LINK3LINK4LINK5LINK6LINK7LINK8LINK9LINK1
0LINK1
1LINK1
2LINK1
3LINK1
4LINK1
5LINK1
6LINK1
7LINK1
8LINK1
9LINK2
0LINK2
1LINK2
2LINK2
3LINK2
4LINK1L
I
N
K2L
I
N
K3L
I
N
K4L
I
N
K5L
I
N
K6L
I
N
K7L
I
N
K8L
I
N
K9L
I
N
K1
0L
I
N
K1
1L
I
N
K1
2L
I
N
K1
3L
I
N
K1
4L
I
N
K1
5L
I
N
K1
6L
I
N
K1
7L
I
N
K1
8L
I
N
K1
9L
I
N
K2
0L
I
N
K2
1L
I
N
K2
2L
I
N
K2
3L
I
N
K2
4L
I
N
K1L
I
N
K2L
I
N
K3L
I
N
K4L
I
N
K5L
I
N
K6L
I
N
K7L
I
N
K8L
I
N
K9L
I
N
K10L
I
N
K11L
I
N
K12L
I
N
K13L
I
N
K14L
I
N
K15L
I
N
K16L
I
N
K17L
I
N
K18L
I
N
K19L
I
N
K20L
I
N
K21L
I
N
K22L
I
N
K23L
I
N
K24L
I
N
K1L
I
N
K2L
I
N
K3L
IN
K4L
I
N
K5L
I
N
K6L
I
N
K7L
I
N
K8L
I
N
K9L
I
N
K1
0L
I
N
K1
1L
I
N
K1
2L
I
N
K1
3L
I
N
K1
4L
IN
K1
5L
I
N
K1
6L
I
N
K1
7L
IN
K1
8L
I
N
K1
9L
I
N
K2
0L
I
N
K2
1L
I
N
K2
2L
I
N
K2
3L
I
N
K2
4L
I
N
K
SUPERVISOR2 WS-X6K-SUP2-2GESTATUSSYSTEMCONSOLEPWR MGMTRESETCONSOLECONSOLE
PORT
MODEPCMCIAEJECTPOR
T 1P
OR
T 2Switch    Load   
100%
1%LINK
LINKSUPERVISOR2 WS-X6K-S
UP2-2G
ESTATUSSYSTEMCONSOLEPWR MGMTRESETCONSOLEC
ONSOLE
PORT
MODEPCMCIAEJECTPORT 1PORT 2Switch    Load   
100%
1%LINK
LINK
1
2
3
4
5
6
7
8
9
10
11
12
13
113977
Grounding
pad 
Grounding lug Wire
Screws (M4) 
						

							1-58
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Installing the Switch
  Establishing the System Ground
Figure 1-32 System Ground Location (Catalyst 6509-NEB-A and Catalyst 6509-V-E)
113678INPUT
OKFA N
OKOUTPUT
FAIL
o
INPUT
OKFA N
OKOUTPUT
FA I L
o
System ground
connectors
System ground
connector
Grounding lug
Wire
POW
ER SUPPLY 1
POW
ER SUPPLY 2
W
S
-S
U
P
32-G
E
-3BSTA
TU
S
S
YSTE
M
A
CTI
VE
PWR
 M
GMT
R
ES
ETC
ATA
L
Y
S
T   6500
 S
U
PE
RV
IS
O
R
  E
N
G
IN
E
  32
C
O
N
S
O
L
E
E
J
E
C
TD
IS
K
 
0P
O
RT
 
1
P
O
RT
 2
P
O
RT
 
3
P
O
RT
 4P
O
RT
 
5
P
O
RT
 6
P
O
RT
 
7P
O
RT
 8P
O
RT
 
9
U
SB
 
2
.0
L
IN
K
L
INK
L
INK
LI
NK
LIN
K
LIN
K
L
IN
K
L
INK
LI
NK
W
S
-S
U
P
32-G
E
-3BSTA
TU
S
S
YSTE
M
A
CTI
VE
PWR
 MGMT
R
ES
ETC
ATA
LY
S
T   6500
 S
U
PE
RV
IS
O
R
  E
N
G
IN
E
  32
C
O
N
S
O
L
E
E
J
E
C
TD
IS
K
 
0P
O
RT
 
1
P
O
RT
 2
P
O
RT
 
3
P
O
RT
 4P
O
RT
 
5
P
O
RT
 6
P
O
RT
 
7P
O
RT
 8P
O
RT
 
9
U
SB
 
2
.0
L
IN
K
L
INK
L
INK
LI
NK
LIN
K
LIN
K
L
IN
K
L
INK
LI
NK
WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48
WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48WS-X6548-GE-TX
STATUS
48 PORT10/100/1000
BASE-T GESWITCHING MODULE
123456789101112
131415161718192021222324
252627282930313233343536
373839404142434445464748PHONE
1
     211
     1213
     1423
     2425
     2635
     3637
     3847
     48