Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual

							DPT Overview
User Manual41
To adjust the ringer volume
VOLUME
7230 / 7235

Ringer:***
(-volume level 3) While the telephone is ringing;
Press VOLUME (UP    /DOWN   ) Control button.
VOLUME
S 1
S 2
S 3
RING
7230 / 7235
Press RING (S2).
Press VOLUME (UP    /DOWN   ) Control button.
The telephone will stop ringing in about 4 seconds. 
When the volume level is 0 (no * indication), the display shows RNGOFF. While the telephone is idle and on-hook;
The telephone will ring. 
OFF       HIGH
LOW
7220 / 7250
Adjust the RINGER Volume Selector lever to 
the desired setting (OFF/LOW/HIGH). 
						

							DPT Overview
42User Manual
To adjust the speaker volume
SP-PHONE
VOLUMEMONITOR
72XX
Press SP-PHONE 
or MONITOR.

SP:************
(-volume level 12)
You may also adjust the speaker volume while listening to 
background music (BGM On mode), receiving a voice call,
receiving a page or hearing a call progress tone such as a dial tone. 
Press VOLUME (UP    /DOWN   ) Control button. 
						

							DPT Overview
User Manual43
1.1.7 LED Indication
The Light Emitting Diode (LED) buttons indicate the line conditions with lighting patterns. 
Flashing light patterns
LED Indication on the INTERCOM Button
The table below shows the lighting patterns for intercom line conditions.
LED Indication on the CO Button
The table below shows the lighting patterns for CO line conditions.
— Items marked with * are only available on the Single-CO button.INTERCOM button Intercom Line Condition
Off
Green On
Green slow flashing
Green moderate flashing
Green rapid flashingIdle
Intercom call / Conference established
Intercom call hold
Intercom call exclusive hold / Consultation hold
Incoming intercom/doorphone call
CO Button Outside Line Condition
Off
Green On
Green slow flashing
Green moderate flashing
Green rapid flashing
Red On
Red slow flashingIdle
You are using the line.
You have a held call.
You have one of the following:
(1) Exclusive hold,
(2) Outside-to-Outside line call, or
(3) Conference, unattended
Privacy Release possible* / Hold Recall / 
Incoming call
Other-use / Log-out
Other-hold*
Slow flashing
(60 flash/min)
Moderate flashing
(120 flash/min)
Rapid flashing
(240 flash/min)
1 s 
						

							DPT Overview
44User Manual
BLF on DSS Button
The Busy Lamp Field (BLF) indicator button is red when the corresponding extension is busy. 
This is available for Direct Station Selection (DSS) buttons on DSS consoles and for flexible 
CO buttons assigned as DSS buttons on proprietary telephones.
LED Indication on the FWD/DND Button
The table below shows the lighting patterns for the FWD/DND Button.
Programming Guide Reference
[990] System Additional InformationSystem Programming [990] 
Area (09), Bit (4,3)When Call Forwarding 
(FWD) is setWhen Do Not Disturb 
(DND) is set
11 (default)
10
01
00Red Slow Flashing
Red On
Red On
Red Slow FlashingRed On
Red On
Red Slow Flashing
Red Slow Flashing 
						

							Station Programming
User Manual45
Section 2
Station Programming
Note: All illustrations used in this section are based on 
model KX-T7235. 
						

							Station Programming
46User Manual
2.1 Station Programming Instructions
2.1.1 Station Programming Instructions
Station Programming allows you, the proprietary telephone (PT) users, to program certain 
features from your telephone individually. To program, you need to switch your telephone to 
the Station Programming mode. During programming mode, your telephone is in the busy 
condition to both inside and outside callers. If you want to make a normal call handling 
operation, you must finish the programming mode.
Programming Mode Display
When you enter into the Station Programming mode, the display shows the following message 
as the initial programming mode;
We recommend a PT with display for Station Programming to avoid mis-operation.
The display also gives you helpful or stored data information related to your programming 
steps. In this section, we note the display example in the programming steps, if required. You 
can also refer to the Display Examples in the Appendix (Section 6).
Entering Station Programming mode
PT-PGM Mode
PT
Press PROGRAM.
Dial 99.
PROGRAM99

Be sure that the telephone is idle and on-hook.
PT-PGM Mode
If there is no entry within one minute, the Station Programming mode
is canceled and normal call handling mode resumes automatically.
The STORE indicator lights.
If 99 is not dialed within 5 seconds after the PROGRAM button is
pressed, the Station Programming mode is canceled.
   Initial programming display 
- 
						

							Station Programming
User Manual47
Exiting Station Programming mode
PT
Press PROGRAM or lift the handset.
PROGRAM
To exit the Station Programming mode, press PROGRAM. You are in
the call handling mode.
When the display shows the initial programming mode;
or 
						

							Station Programming
48User Manual
Confirming the assigned function data
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM] or lift the handset.
— If you wish to change the data, follow the programming procedure explained in this section.
PT
Press HOLD (END). Enter the program access number.
program access numberHOLD
Enter the program access number* as follows.
-  1:Preferred Line Assignment 
- Outgoing
-  2:Preferred Line Assignment 
- Incoming
-  3:Full One-Touch Dialing Assignment 
-  4:Intercom Alert Assignment
-  5:Call Waiting Tone Type Assignment
-  6:Self-Extension Number Confirmation
-  7:Live Call Screening Mode Set
 
-81:Initial Display Selection
-82:Bilingual Display Selection
- 9:Handset/Headset Selection
-01:Remote Station Look Control (
- Operator / Manager only)
-02:Call Log Lock Control, Incoming (
- Operator / Manager only)
-03:Live Call Screening Password Control  (
- Operator / Manager only)
-  #:Station Programming Data Default Set
The display shows the programmed data.

When you press [5], the display shows:
(- The Call Waiting tone is currently programmed to Tone 1.)
The display shows the initial programming mode.
C.W. Tone1
† : Available when the Digital Super Hybrid System is connected to a Digital Proprietary Telephone capable Panasonic
    Voice Processing System (one that supports digital proprietary telephone integration; e.g., KX-TVS100) * A programming access number is required to program/confirm the function data by Station Programming.
†
† 
						

							Station Programming
User Manual49
Confirming the assigned data on the Flexible button
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit Station Programming mode: Press [PROGRAM] or lift the handset.
— If you wish to change the data, follow the programming procedure explained in this section.
Clearing the data on the Flexible button
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit Station Programming mode: Press [PROGRAM] or lift the handset.
— The lists on the following pages are the buttons and programming access numbers used for 
 Station Programming. Detailed operating instructions are explained on each page in this 
 section.
The display shows the initial programming mode.The display shows the current status.
PT
Press HOLD (END). Press the desired Flexible
(CO,DSS,PF) button.
HOLD
PT
Press the desired Flexible
(CO, DSS, PF) button that
you wish to clear.  Dial 2.Press STORE.
AUTO DIAL
STORE2
The STORE indicator lights.
The display shows the initial programming mode. 
						

							Station Programming
50User Manual
Station Programming [Flexible Button Assignment]
(Station Programming)
Direct Station Selection (DSS) Button
One-Touch Dialing Button
Message Waiting (MESSAGE) Button
FWD/DND Button
SAVE Button
Account Button
Conference (CONF) Button
Log-In / Log-Out Button
Phantom Extension Button
Night Button
Voice Mail (VM) Transfer Button
Two-Way Record Button
Two-Way Transfer Button
Live Call Screening (LCS) Button
Live Call Screening (LCS) Cancel Button
Single-CO (S-CO) Button
Loop-CO (L-CO) Button
Group-CO (G-CO) Button
(Ringing Tone Selection for CO Button)
(Ringing Tone Selection for Intercom Calls)
(Phantom Extension Ringing On/Off Set)
(Station Speed Dialing Number / Name Assignment)
[KX-T7235/KX-T7431/KX-T7433/KX-T7436 only]
(Exit)
1
2
3
4
5
6
70
71
72
8
90
91
92
93
0
#
PROGRAM99
CO
DSS
PF
COCO
73
Phantom
(F1 - F10)
Phantom
Function
PROGRAM
INTINT
  : Available when the Digital Super Hybrid System is connected to a Digital Proprietary Telephone capable Panasonic
    Voice Processing System (one that supports digital proprietary telephone integration; e.g., KX-TVS100).