Panasonic Kx-Td816c, Kx-td1232c Digital Super Hybrid System User Manual

							User Programming
User Manual91
3.2.6 [017] DISA User Codes
Description
Assigns the Direct Inward System Access (DISA) User Codes and a Class of Service (COS) to 
each code. The code COS determines the toll restriction level of the DISA caller.
Wa r n i n g
When you enable the Outside-Outside Line Call feature of DISA function, if a third party 
discovers the password (a DISA User Code) of the system, you have a risk that they will make 
illegal phone calls using your telephone line, and the cost may be charged to your account.
In order to avoid this problem, we strongly recommend the following points:
1: Carefully maintain the secrecy of the password.
2: Specify a complicated password as long and random as you can make it.
3: Change the password frequently.
Selection
DISA user code number: 01 through 32
DISA user code: 4 through 10 digits
COS number: 1 through 8
Default
All DISA user code numbers - DISA user code=Blank; COS number=8 
						

							User Programming
92User Manual
Programming
Conditions
This setting is required if Trunk (Outside line) Security mode is selected in program [809] 
DISA Security Type.
Each code should be unique and composed of four through ten numerical digits, 0 through 
9.
User Manual References
4.3.34 Direct Inward System Access (DISA)
Display PT
Dial 017. Enter a DISA user code number (01-32).
017DISA user code no.
  
User Code NO?→
 [When SELECT is pressed]
Repeat these steps
Enter a DISA user 
code (Blank or 4-10 
digits).
DISA user code
Press NEXT or
PREV or SELECT.Enter the desired
DISA user code number.
DISA user code no.
To delete the current entry, press CLEAR. 
To change the current entry, press CLEAR
and enter the new name.
017 USER CODES
To enter user code number 01, you 
can also press NEXT.

01:       C:8
Enter COS 
number (1-8).
COS no.
Press NEXT.
NEXT
Press →.Press STORE.
STORE
SELECT
PREV
NEXT
Press END.
END 
						

							Station Features and Operation (DPT/SLT)
User Manual93
Section 4
Station Features and Operation (DPT/SLT) 
						

							Station Features and Operation (DPT/SLT)
94User Manual
4.1 Before Operating
4.1.1 Before Operating
What kind of telephone do you use?
In this manual, you will find your way to operate the feature depending on the telephone you 
use. Please use the proper operation for your telephone.
 
If you use a Panasonic proprietary telephone which has the special function button and/or 
the display, you will follow the operation with the button or display for easy access.
If you use a Panasonic proprietary telephone which does not have the function button, 
you may change one of the unused buttons to another button. Refer to 2.2 Station 
Programming.
A Panasonic proprietary telephone has the Light Emitting Diode (LED) button 
indicators, so you can see the line conditions by the lighting patterns.
If Idle Line Preference — Outgoing, No Line Preference — Outgoing or Prime 
Line Preference (CO Line) — Outgoing is assigned on the extension, it is not possible 
to have access to any DPT features after simply going off-hook. To access DPT features, 
press the INTERCOM button after going off-hook.
If you use single line devices such as a single line telephone or data terminal, you will follow 
the steps which enter the feature number. 
If you use a dial pulse (DP) type single line device which does not have the   and # 
keys, it is impossible to access features that have   or # in their feature numbers.
When the Pickup Dialing (Hot Line) feature is set on your telephone, the dialing 
sequence should be done within a certain period of time (Pickup Dial Waiting Time — 
default: 1 s) after lifting the handset.
This time can be changed by System Programming.
If you use a ISDN telephone which are connected to the optional ISDN Line Unit, KX-
TD284, can perform features in this section. However, there are some exceptions. 
						

							Station Features and Operation (DPT/SLT)
User Manual95
Operation Step Box
In this section, operations for extension users are described using the following Operation Step 
Box.
Note
If your telephone is not noted in the operating step box (ex., only PT is noted), this means 
your telephone does not have the ability to execute that feature.
If your telephone has the ability to perform several operations for one feature, you can select 
the method according to your needs.
In this manual, the default feature numbers are used to describe each operation and 
illustration. Use the new programmed numbers if default feature numbers are changed by 
System Programming.
For proprietary telephone operations, all button illustrations are based on the model KX-
T7235.
Description of Symbols Used
In this section, many symbols are used. Most symbols do not need a description, but some 
symbols do. They are as follows.
Lift the handset, or press the SP-PHONE or MONITOR button. (Off-hook)
Replace the handset, or press the SP-PHONE or MONITOR button. (On-hook)
7230 / 7235 / 7433 / 7436PT and SLT
2Wait for an answer
and talk.
Wait for an answer
and talk.
BSS
S3S2S1
Dial 2.
Press BSS (S1).
Applicable telephone:
Both PT and SLT users
can follow the operation
steps below.
Applicable telephone:
KX-T7230, KX-T7235,
KX-T7433 and KX-
T7436 users can execute
not only the button
operation but also the
display operation below.
Operation steps 
						

							Station Features and Operation (DPT/SLT)
96User Manual
Flash the hookswitch on a single line telephone.
Tones which vary depending on the condition (Refer to 6.1.3 Tone List). 
						

							Station Features and Operation (DPT/SLT)
User Manual97
4.2 Basic Operations
4.2.1 Making Calls 
Intercom Calling
You can make a call to another extension.
Outward Dialing
You can make a call to an outside party using one of the following line access methods.
a)Line Access, Automatic (default: 9)
b)Line Access, Individual (CO button)
c)Line Access, Outside Line Group (default: 81 through 88)
Any Telephone
The INTERCOM indicator light turns green.
Lift the handset or press 
SP-PHONE/MONITOR.Dial extension number.Press DSS.
extension no.or(DSS)
Talk.Hang up or press
SP-PHONE/MONITOR.
Any Telephone
Dial the phone number.
phone no.
Lift the handset or press
SP-PHONE/MONITOR.
Hang up or press
SP-PHONE/MONITOR.Dial toneTalk.
(CO)
For PT: Press CO assigned
             as Loop-CO / 
             Group-CO / Single-CO.
For any telephone: Dial the line access 
code (9 or 81 through 88).
For PT
The display shows the
phone number.
line access codeFor any
telephone
The selected CO indicator
light turns green. 
						

							Station Features and Operation (DPT/SLT)
98User Manual
Conditions

There are four types of Line Preference for outgoing calls (— Idle Line/No Line/Prime 
Line/Prime INTERCOM Line). Each preference can be selected by Station or System 
Programming.
With the KX-T7431, KX-T7433, KX-T7436 or KX-T7235, you can execute the 
Intercom Calling feature to extensions by using the Extension Dialing display 
feature.
Helpful hints for the Handsfree (speakerphone) operation are noted in the Handsfree 
Operation feature.
User Manual References
2.2.1 Initial Settings
4.3.48 Hands-free Operation [PT only]
4.3.49 Intercom Calling
4.3.61 Outward Dialing, Line Access — SUMMARY
4.5.8 KX-T7235 Display Features - Call Directory
4.5.11 KX-T7431 / KX-T7433 / KX-T7436 Display Features - Call Directory 
						

							Station Features and Operation (DPT/SLT)
User Manual99
4.2.2 Receiving Calls
Conditions

There are three types of Line Preference for incoming calls (— No Line/Prime Outside 
Line/Ringing Line). Each preference can be selected by Station Programming.
Helpful hints for the Handsfree (speakerphone) operation are noted in the Handsfree 
Operation feature.
Programming Guide References
[400] Outside Line Connection Assignment
[603-604] DIL 1:N Extension and Delayed Ringing —— Day / Night
User Manual References
2.2.1 Initial Settings
4.3.4 Answering, Direct Outside Line [PT only]
4.3.48 Hands-free Operation [PT only]
PTAny Telephone
The CO or INTERCOM indicator light
turns steady green.
Lift the handset or press SP-PHONE
/MONITOR.Press a rapid flashing CO or INTERCOM.
or(CO)INTERCOM 
						

							Station Features and Operation (DPT/SLT)
100User Manual
4.3 Station Features and Operation
4.3.1 Absent Message Capability
You can select one of nine pre-programmed Absent Messages (1-9) for your extension. The 
display PT users calling your extension see the message you select. Absent messages are used 
to inform the party calling to your extension of the reason for your absence. By default, 
Messages No. 1-6 are provided with default messages and the other three messages are left 
blank.