Lucent Technologies Definity Audix System Digital Networking Guide

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-11 Paradyne Comsphere 3810plus/3820plus/3910 Front Panel Settings 
8
Linefeed  Char 010 ASCI
Result Codes Enable
Extend ResltCode Enab le
Re s u l t C o d e Fo r m Wo r d s
AT Cmnd  Mod e Normal
Line_Dialer Setting Notes
AutoAnswerRing # 1
AT c ommand s0= 1
Dialer Type Tone
DialTone Detec t Enab le
BusyTone Detec t Enab le
, Pa u s e  Ti m e 2 s e c
NoAnswer Timout 45sec
Fast Disc onnec t Disab le
Long  Sp ac e DiscDisable
AT c ommand y0
No Carrier Disc 2sec
No Data Disc Disable
MakeBusyViaDTR Disab le
Dial_Line Setting Notes
Mod ulationV32bis/terbo
Dial Line Rate19200(V32t) 
or
9600(V32b)
AT c ommand s41= 20 
AT c ommand s41= 3
Automod eDisable
AT c ommand s76= 1
AutorateDisable
AT c ommand s78= 1
Dial TX Level Permissv(-9)
V22b  Guard  Tone Disab le
Train Time Long
Asymmetric  Rate Enab le
Fa l l  Fw d  D e l a y D i s a b l eDTE_Dialer Setting Notes 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-12 Paradyne Comsphere 3810plus/3820plus/3910 Front Panel Settings 
8
V42/MNP/Buffer Setting Notes
Err Contrl Mod eBufferMode
AT c ommand  
0
EC Neg otiat Bfr Disab le
Flw Cntl of DTE CTS_to_DTE
AT c ommand \q 3
Flw Cntl of Md m RTS to Md m
XON / XOFF Ps t h r u D is a b le
Md m/Md m FlowCtl Disab le
Break Buffr Ctl Keep _Data
Send  Break Cntl Data_First
Tx Buff Disc  Delay 10sec
Rx Buff Disc  Delay Disab le
Max Frame Size 256
Cellular Enhanc e Disab le
Test Setting Notes
DTE RL (CT140) Disab le
DTE LL (CT141) Disab le
Test Timeout Disab le
Rc v Remote Loop Enab le
V54 Ad d ress Disab le
Misc Setting Notes
Strap sWhenDisc No_Chang e
Sp eaker Control OnUntilCarr Some loc ations may p refer Off 
AT command m0
Sp eaker Volume Med ium
Ac c ess frm Remt Enab le
RemAc c ssPasswrd 00000000
Dir#1_Callback Disable
CellurRJ11 Adpt Disable 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-13 Paradyne Comsphere 3810/3820 Front Panel Settings 
8
Paradyne Comsphere
3810/3820 Front Panel Settings
The following tab le shows the front p anel setting s for the Parad yne Comsp here 
3810 and  3820 mod ems. Security Setting Notes
NMS_Rep orting 00
Answer_Sec ur No_Answ_Sec
Orig inate_Sec ur No_Orig_Sec
Table 8-2.  Paradyne Comsphere 3810/3820 Modem Settings 
(Bold
 Setting s are Chang es from Fac tory Setting s)
DTE_Interface Setting Notes
Async/Sync  Mod e Async
Async  DTE Rate 19200 or
9600AT c ommand  s41= 20
AT c ommand  s41= 3
Asyn #Data Bits 8
Asyn Parity Bit None
Asyn #Stop  Bits 1
DTR Ac tionStndrd_RS232
AT c ommand  &d 2
DSR ControlWinkWhenDisc
AT c ommand  &s2
RTS Ac tion Ig nore
CTS Control Forc ed _On
RTS/ C TS D e la y 0  m se c
LSD ControlWinkWhenDisc
AT c ommand  &c 2
CT111_Rate Cntl Disab le
DTE_Rate= VF Disab le 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-14 Paradyne Comsphere 3810/3820 Front Panel Settings 
8
DTE_Dialer Setting Notes
DTE Dialer Typ e AT
AT Esc ap e Char128 ASCI
AT c ommand  s2= 128
Escape GuardTim 1 sec
BreakForc eEsc ap Disab le
CommandCharEc ho Enab le
Carriag eRtnChar 013 ASCI
Bac ksp ac e Char 008 ASCI
Linefeed  Char  010 ASCI
Result Codes Enable
Extend ResltCode Enab le
Re s u l t C o d e Fo r m Wo r d s
AT Cmnd  Mod e Normal
Line_Dialer Setting Notes
AutoAnswerRing # 1 AT c ommand  s0= 1
(Some c ountries req uire this to 
be set to another value. Chec k 
particular c ountry modem 
reg ulations.)
Dialer Type Tone
DialTone Detec t Enab le
BusyTone Detec t Enab le
, Pa u s e  Ti m e 2 s e c
NoAnswer Timout 45sec
Fast Disc onnec t Disab le
Line Crnt Disc Enab (> 8msec )
Long  Sp ac e DiscDisable
AT c ommand  y= 0
No Carrier Disc 2sec
No Data Disc Disab le
MakeBusyViaDTR Disab le
MI/MIC Dialing Disab le 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-15 Paradyne Comsphere 3810/3820 Front Panel Settings 
8
Dial_Line Setting Notes
Dial Line Rate19200(V32t)
9600(V32b)AT c ommand  s41= 20
AT c ommand  s41= 3 
Automod eDisable
AT c ommand  s76= 1
AutorateDisable
AT c ommand  s78= 1
Dial TX Level Permissv(-9)
V22b  Guard  Tone Disab le
V32b is Train  Long
Fall Fwd  Delay Disab le
V42/MNP/Buffer Setting Notes
Err Contrl Mod eBufferMode
AT c ommand  
0
Flw Cntl of DTE CTS_to_DTE AT c ommand  \q 3
Flw Cntl of Md mRTS to Mdm
AT c ommand  \q 3
Md m/Md m FlowCtl Disab le
Break Buffr Ctl Keep _Data
Send  Break Cntl Data_First
TxBuff Disc  Delay 10sec
RxBuff Disc  Delay Disab le
Test Setting Notes
DTE RL (CT140) Disab le
DTE LL (CT141) Disab le
Test Timeout Disab le
Rc v Remote Loop Enable
V54 Ad d ress Disab le 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-16 Paradyne Comsphere 3810/3820 Front Panel Settings 
8
Misc Setting Notes
Strap sWhenDisc No_Chang e
Sp eaker Control OnUntilCarr Some loc ations may p refer Off
 
AT c ommand  m0
Sp eaker Volume Med ium
Ac c ess frm Remt Enable
RemAc c ssPasswrd 00000000
Dir#1_Callb ac k Disab le
NetMng mtAd d ress 001
NMS_Call_Msg s CallCnc t&Prg
NMS DTR Alarm Disab le
CellurRJ11 Adpt Disable
Security Setting Notes
NMS_Rep orting 03
Answer_Sec ur No_Answ_Sec
Orig inate_Sec ur No_Orig _Sec 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-17 7400A Option Settings 
8
7400A Option Settings
The 7400A fac tory d efault user interfac e is set for the Hayes AT c ommand  set. 
The DEFINITY AUDIX system need s to have the user interfac e set for Keyb oard  
Dial. 
Use the following  p roc ed ure to c hang e the user interfac e:
1. Press the NEXT/NO or BACK b uttons on the front p anel until the SET 
INTERFACE?
 op tion ap pears. 
2. Press the ENTER/YES b utton to selec t the interfac e menu. 
3. Use the NEXT/NO b utton until INT -> KYBD DIAL? 
ap p ears on the 
LCD. 
4. Press the ENTER/YES b utton to selec t the Keyboard Dial
 op tion. 
The 7400A will perform a selftest and  initialize the Keyb oard  Dial user interfac e.
Set the following  op tions using  the SET OPTIONS? 
menu. Refer to the 
7400A 
Data Mod ule User’s Manual
, 555-020-706, for more information on the front p anel 
setting s.
Table 8-3. 7400A Option Settings 
Set Option Displays Setting
Set 300 Sp eed ? no
Set 1200 Speed ? no
Set 2400 Speed ? no
Set 4800 Speed ? no
Set 9600 Speed ? no
1
Set 19200 Sp eed ? yes
Se t  A n s w e r ? Au t o
Set Break Disc ? Long
Set CI Lead ? off
Set CH Lead ? off
Set CTS Lead ? on
Set DCD Lead ? on
Set DSR Lead ? on
Set DTR Detec t? 50 msc
Continued on next page 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Hardware Installation for DCP Mode 2 
8-18 7400A Option Settings 
8
Set DTR Lead ? Follow2
Set LL Lead ? off
Se t  Pa r i t y ? Sp a c e
Set Remote Loop ? Grant
Set RI Lead ? on
Set RL Lead ? off
Se t  Si g ls  D is c ? o n
Set TM Lead ? off
1. If DEFINITY AUDIX Dig ital Networking  is to b e set at
9600 b p s, set 9600 to yes and  19200 b p s to no.
2. On Paradyne Comsphere 3800 Mod ems this setting
should  b e set to Follow. On other mod em typ es the
Ignore setting  may b e req uired .
Table 8-3. 7400A Option Settings  — Continued
Set Option Displays Setting
Continued on next page 
						

							Initial Network Administration and Acceptance Tests 
9-1  
9
DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
9
Initial Network Administration and
Acceptance Tests
This chapter contains instruc tions for performing initial digital networking 
ad ministration and ac c ep tanc e tests on the DEFINITY AUDIX system. 
Ac c ep tanc e tests are network c hec ks p erformed  b efore p rovid ing  networking  
c ap abilities to sub sc rib ers. This c hap ter p resents:
nAdministering the digital networking ports on the switc h
nAd ministering mod ems, async hronous d ata units (ADUs), and  d ata 
mod ules on the switc h for DCP Mode 2
nAd ministering the loc al DEFINITY AUDIX system for d ig ital networking  and  
p erforming  a test mac hine on the loc al system
nAd ministering the remote systems on the loc al DEFINITY AUDIX system
nAd ministering the DEFINITY AUDIX system on the remote systems
nTesting  networking  c onnec tions
nAd d ing  test sub sc rib ers to the loc al and remote systems and  testing these 
sub sc rib ers
nAd d ing  remote sub sc rib ers to the loc al system
nSetting  weekly b ac kup  p arameters, traffic  c ollec tion, and  c all transfer out 
of AUDIX
nRecord ing  remote system names on the local system 
						

							DEFINITY AUDIX System Digital Networking  585-300-534  Issue 2
May 1999
Initial Network Administration and Acceptance Tests 
9-2 Switch Administration 
9
Switch Administration
Refer to the information you rec eived  from the d esig n c enter when c ompleting  
the switc h ad ministration. 
Before beg inning this ad ministration, ob tain the first two voic e p ort extensions for 
the loc al DEFINITY AUDIX system from the Voic e Group sc reen (display 
voice-group
) on the DEFINITY AUDIX system if you d o not alread y have these 
extensions availab le (refer to DEFINITY AUDIX Ad ministration later in this c hap ter 
for log in p roc ed ures).
Log  in to the switc h ad ministration terminal. Refer to your switc h ad ministration 
d oc umentation for log in p roc edures. 
Task 1: Administer the Digital Networking Ports 
Ad minister a Data Mod ule sc reen on the switc h for eac h networking  p ort. For the 
first networking  p ort, administer the Data Mod ule sc reen for voic e p ort 1. For the 
sec ond  networking  p ort, ad minister the Data Module sc reen for voic e p ort 2. 
Use the following  p roc ed ure to administer a Data Mod ule sc reen:
1. For the first voic e p ort, enter change station
 
extension (extension 
numb er of the first voic e p ort) at the switc h administration terminal. The 
first p ag e of the Station sc reen d isp lays for the voic e p ort.
2. Enter a y
 in the Data Module field. This adds a Data Module screen for the 
station.
3. Pag e to the Data Mod ule sc reen. 
4. In the Data Extension field , enter a uniq ue extension from the switc h 
dialing plan.
5. In the Name field  (op tional), enter a name that id entifies the networking  
port.
6. Enter a COR and COS for the networking port that reflects the desired 
COS and /or COR for the port. Use a sep arate c lass of servic e with d ata 
p rivac y and no restric tions.
7. In the ITC field (Information Transfer Cap ab ility) for G3V2, G3V3, and 
G3V4, enter restricted
.
8. Save the c hang es.
9. Rep eat steps 1 throug h 7 for the sec ond  networking  port if there is one.