Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

							System & Station
Program 03 for DK40i – Flexible PCB Slot Assignments
Strata DK Programming 5/993-5
System & Station
Program 03 for DK40i - Overview
Program 03 tells the system what type of optional PCBs are installed in the Expansion KSU. You 
must run Program 03 after installing PCBs with options such as OCA, DIU, etc. Also, run Program 
03 for each PCB slot when installing a PCB in that location.
It is not necessary to run Program 03 for slots 00~14. The DK40i automatically assigns the Base 
KSU PCBs if they are installed when system power is turned ON. However, if DSS is required on 
the Base KSU’s DKT circuit 8, you must run Program 03 to assign code 64 to slot 11. If universal 
PCBs are installed, Program 91-1 and 91-9 automatically assign the appropriate PCB codes to the 
installed slots. But, Programs 91-1 or 91-9 do not assign option codes (such as OCA, DIU, etc.).
Codes allowed in DK40i Expansion KSU: 11, 13, 16, 21~28, 31, 41, 61~62, 64~66, 77, 78, 91, 92, 
and 81.
CAUTION!Running Program 91-9 erases Program 03 option codes; Program 91-1 does 
not.
Important!After completing Program 03 set the configuration in memory by running OFF and 
wait five seconds before turning it back ON.
The Program 03 record sheet is the main record for the hardware configuration of the entire 
system. It provides space to record station ports assigned to the station, Tie, and DID line PCBs 
and line numbers assigned to the ground loop start, CO, Tie, and DID line PCBs. Use the PCB 
Code Reference Table on the Program 03 record sheet to determine the proper option code for each 
PCB with an option.
The DK40i Base KSU is divided into four fixed slots, even through the unit has no slots per se.
©Slot 00 represents the system’s common control (TMAU2) and optional K4RCU3, K5RCU, or 
K5RCU2
©Slot 11 contains the KSU’s eight digital circuits/ports (DKU)
©Slot 12 contains the KSU’s four optional CO or DID line circuits (TCOU or TDDU) or two 
BRI (TBSU) circuits
©Slot 13 contains the four optional standard telephone circuits KSTU2
©Slot 14 contains four optional Caller ID circuits for TCOU (TCIU2)
DK40i Slots 15~18 (Expansion KSU Assignment Criteria)
©Allowed PCBs: PDKU, RDSU/RSTS, RSTU, RSTU2, PSTU, PEKU, PESU, KCDU, RCOU/
RCOS, RGLU2, RCIU2/RCIS, RWIU, PCOU, RDDU, REMU, PEMU, PIOU, PIOUS, 
RSSU, PEPU, Stratagy DK.
NoteSome PCBs cannot be installed in slot 18 (see Chapter 2 – DK40i Configuration).
©Expansion KSU PCBs must be installed in the slots specified in Tables 2-9~2-15 or the system 
may not operate properly. (See tables in Chapter 2 – DK40i Configuration of the Strata DK 
Installation and Maintenance Manual.)
©Slots 15 and 16 support Speaker OCA and RPCI/DIU Data Switching; slots 17 and 18 do not. 
All slots support Handset OCA and RPCI-DI TAPI operation.
©On DK40i, RCIU2 must be installed in slot 17; RCIU1 cannot be used.
©The RWIU must be installed in slot 15 and slot 16 must be vacant to support 9 to 16 wireless 
handsets. It can be installed in any expansion slot to support 1~8 wireless handsets.
©If the RWIU supports 9 to 16 handsets, program code 61 in slot 15 and 16. 
						

							System & Station
Program 03 for DK424 – Flexible PCB Cabinet Slot Assignments
3-6Strata DK Programming 5/99
Program 03 for DK424 – Flexible PCB Cabinet Slot 
Assignments
Processor Type:All RCTUs
Program Type:System
Initialized Default:PCB codes of PCBs installed prior to running Programs 91-1 or 91-9;
Code 00 for empty slots




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG 
DK424 Base Cabinet 1
Slot Number00
(R11)01 
(RCTU)S11S12S13S14S15S16
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
DK424 Expansion Cabinet 2
Slot NumberS21S22S23S24S25S26S27S28
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
DK424 Expansion Cabinet 3
Slot NumberS31S32S33S34S35S36S37S38
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
DK424 Expansion Cabinet 4
Slot NumberS41S42S43S44S45S46S47S48
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
more codes
SELECT = Slot Number (00, 01, 11~78)
CARD = PCB Code (See Reference Table)Turn System Power OFF (5 sec) then ON.
or...
Run Program 91-2 
						

							System & Station
Program 03 for DK424 – Flexible PCB Cabinet Slot Assignments
Strata DK Programming 5/993-7
System & Station
DK424 PCB Codes
See the following text for specific installation rules on the above PCBs. DK424 Expansion Cabinet 5
Slot NumberS51S52S53S54S55S56S57S58
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
DK424 Expansion Cabinet 6
Slot NumberS61S62S63S64S65S66S67S68
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
DK424 Expansion Cabinet 7
Slot NumberS71S72S73S74S75S76S77S78
PCB Code
PCB Type
Options
Station/Tie/DID/ISDN
Port Numbers
CO/Tie/DID/ISDN Line Numbers
PCBCodePorts/TypePCBCodePorts/Type
RCOU, RGLU2 11 4 Gnd./Loop Lines RDTU 71 8 T1 Channels
RCOU/RCOS 17 8 Loop CO Lines RDTU 72 16 T1 Channels
RDDU 16 4 DID Lines/4 Stations RDTU 7324 T1­channels
REMU 13 4 Tie Lines/4 Stations RCTU 91 None
PEKU 21 8 Stations RCTU (with 4-CKT RRCS) 92 None
PEKU (EOCU) 22 8 Stations RCTU (with 8-CKT RRCS) 93 None
PEKU w/DSS 23 8 Stations RCTU (with 12-CKT RRCS) 94 None
PEKU (DSS, EOCU) 24 8 Stations NONE 00 00
PESU 25 6 Stations RATU 51 4 Stations
PESU (OCA) 26 6 Stations RSIU 49 I/O Interface
RDSU/RSTS 27 8 Stations RCIU2/RCIS 81 8 CKT, Caller ID
RDSU/RSTS (OCA, DIU) 28 8 Stations Stratagy DK 31 8 VM Ports
RSTU2 31 8 Stations RBUU without RBUS  75 2 U Interfaces 
(4 stations/4 CO lines)
PIOU, PIOUS/ RSSU, PEPU 41 Remote Maintenance (TTY) RBUU with RBUS 76 4 U Interfaces
(8 stations/8 CO lines)
PIOU/PIOUS/RSSU 42 MIS for ACD (TTY) RBSU without RBSS 77 2 S/T Interfaces
(4 stations/4 CO lines)
PIOU/PIOUS/RSSU 43 SMDI VM Interface (TTY) RBSU with RBSS  78 4 S/T Interfaces
(8 stations/4 CO lines)
PDKU2, RWIU 61 8 Stations RPTU Interface Card 79 PRI Interface
(24 CO lines)
PDKU2 (OCA, DIU) 62 8 Stations
PDKU2 (DSS, OCA, DIU) 64 8 Stations 
						

							System & Station
Program 03 for DK424 – Flexible PCB Cabinet Slot Assignments
3-8Strata DK Programming 5/99
Program 03 for DK424 - Overview
Program 03 tells the system what type of optional PCBs are installed.
The Program 03 record sheet is the main record for the hardware configuration of the entire 
system. It provides space to record station ports assigned to the station, Tie, and DID line PCBs 
and line numbers assigned to the ground loop start, CO, Tie, and DID line PCBs.
Use the DK424 PCB Code table on Page 3-7 to determine the proper option code for PCBs with 
options. You must run Program 03 after installing PCBs with options such as OCA, RRCS, DIU, 
etc. Also, run Program 03 for the slot of each new PCB when installing a new PCB in an existing 
installation.
If universal PCBs are installed, Program 91-1 and 91-9 automatically assigns the appropriate PCB 
codes to the installed slots. But, they do not assign option codes (such as OCA, PDIU, RRCS, 
etc.).
CAUTION!Running Program 91-9 erases Program 03 option codes; Program 91-1 does 
not.
Important!After completing Program 03 set the configuration in memory by running Program 
91-2 or turn the base cabinet power supply switch off and wait five seconds before 
turning it back on.
Expansion slots 7 and 8 can only be used if the following equipment is installed: 
DK424 Base (with RCTUE/F and MBJU removed) and the DK424 Expansion.
See Chapter 4 – DK424 Configuration (Strata DK Installation and Maintenance 
Manual) to determine PCB slot placement.
PIOU/PIOUS/RSSU
Codes 41, 42, and 43 assigns PIOU/PIOUS RSSU TTY port as Remote Maintenance, MIS for 
ACD, and SMDI respectively; SMDR, Paging, Relay Control, and other miscellaneous options are 
active on the PIOU/PIOUS that has the lowest number code (41, 42 or 43) in the system. Codes set 
for RSIU/RSIS/RMDS in Program 76 have priority over codes 41, 42, and 43. 
Piggyback PCB / Speaker OCA / Data Interface Unit Options
Run Program 03 to assign codes for all options except RCOS. Program 91-9 erases option codes 
assigned with Program 03; Program 91-1 does not erase option codes already programmed. After 
completing all Program 03 data entry, run Program 91-2 or cycle system power to transfer 
Program 03 data into working memory. 
						

							System & Station
Program 03 for DK424 – Flexible PCB Cabinet Slot Assignments
Strata DK Programming 5/993-9
System & Station
RCIU/RCIS or RCIU2/RCIS
When installing RCIU2/RCIS, enter the Caller ID circuit numbers on the record sheet in place of 
the CO line number. Each RCIU2/RCIS slot uses eight Caller ID circuits. RCIU2/RCIS circuit 
numbers are assigned automatically in numerical order (001~200) starting with the lowest slot 
number, to the highest RCIU2/RCIS slot number in 8-circuit increments.
Important!If more than four circuits are needed, never install an RCIU without an RCIS.
On DK424, RCIU2/RCIS can be installed in any universal slot except slot 11 or if RSIU is 
installed, slot 12; they do not have to be installed adjacent to corresponding CO lines. Refer to 
Program *50 to manually assign RCIU2/RCIS circuits to CO line circuits.
RWIU
Code 61 must be set for all RWIU slots including slots that are vacant because they support RWIU 
channels 09~32.
RCTU
The table below gives you slot locations and PCB Code Assignments for all RCTUs.
PCB Codes:
91=No RRCS
92=4 -circuit RRCS
93=8 -circuit RRCS
94=12 -circuit RRCS
NoteWhen using RCTUA, Slot 15 and 16 does not support Speaker OCA or DIU Data 
Switching. RCTUA does not support ACD, ACD/MIS, RS-232 Voice Mail Integration 
(SMDI), and attendant console features.
RSIU
If an RSIU is installed in base cabinet slot 11, you must connect the programming station to circuit 
6 in slot 12. In this case, a PDKU or PEKU should be installed in slot 12 and Station Port Number 
000~007 will be in slot 12.
If an RSIU is not installed, you must connect the programming station to circuit 6 in slot 11 (Port 
005) and/or circuit 6 in slot 12 (port 013). The station must be a 20-button digital LCD or 
electronic LCD telephone. Also, if an RSIU is not installed, install a PDKU or PEKU in slot 11.
ProcessorR11 SlotRCTU Slot 
Cabinet 1Slot CodePCB Code 
Assignment
RCTUANo Yes 00 91~94
RCTUBNo Yes 00 91~94
RCTUBAYe s N o 0 0 9 1 ~ 9 4
RCTUBBNo Yes 01 91
RCTUCYe s N o 0 0 9 1 ~ 9 4
RCTUDNo Yes 01 91~94
RCTUEYe s N o 0 0 9 1 ~ 9 4
RCTUFNo Yes 01 91~94 
						

							System & Station
Program 03 for DK424 – Flexible PCB Cabinet Slot Assignments
3-10Strata DK Programming 5/99
Program 03 Example
Action (press buttons + LED buttons)LCD Response
1. Use an LCD programming phone per Minimum Hardware 
Requirements on Page 1-14.No. 205
Jan 20 Sun 06:43
2.




Enter programming mode. (Do not press [DN] button.)Program Mode
3.
6SNU6SHDNHU+ROGAccess Program 03. System beeps after 6SNU6SHDNHU is 
pressed to indicate program number may be entered.Program = 03
Data Store
4.
6SNU6SHDNHUPrepare the system for a selection.03 Select =
5. Dial a PCB slot number (00~78 for DK424 or 00-18 for DK40i) using 
the dial pad.03 Select = (00~78)
Card = (91, 62 or 00)
The system defaults as follows:

Initialized default assigns slot 00 and 01 to be a non-optioned RCTU 
without RRCS DTMF receivers, or DK40i Base without K4RCU3, 
K5RCU, and K5RCU2.03 Select = 00 (Slot Number)
Card = 91

Initialized default assigns slot 11 to be a non-optioned PDKU without 
DSS console or OCA (Code 61).03 Select = 11 (Slot Number)
Card = 61
a (DK424), a (DK40i)
Initialized default assigns slot 12~78 to be empty (Code 00).03 Select = 12~78 (Slot 
Number)
Card = 00
6.
aDial the PCB code recorded on the record sheet. Refer to the PCB 
code reference table on Program 03 record sheet for a definition of the 
codes.03 Select = (00~78)
Card = (00~97)
7.
+ROGSecure data in system programming.03 Select = (00~78)
Data Programmed
8.
6SNU6SHDNHUPrepare system for another selection (go back to Step 5) or continue 
with Step 9.03 Select =
9.
+ROGSecure Program 92 data in system memory.92 Select = ##
Data Programmed
10.
6SNU6SHDNHUExit Program 92 (system beeps). Enter another program number or 
exit programming mode (go to Step 11).Program =
11 .
+ROGExit programming mode.No. 205
Jan 20 Sun 06:58
12. To secure Program 03 entries, Power off for five seconds, then power 
on, or run Program 91-2. 
						

							System & Station
Program *03 for DK424 – Cabinet Type Identification
Strata DK Programming 5/993-11
System & Station
Program *03 for DK424 – Cabinet Type Identification
Processor Type:RCTUE/F only
Program Type:System
Initialized Default:All cabinets = 1
Program *03 - Overview
You must run this program when using the RCTUE/F processor. It identifies which type of 
cabinets are installed (DK424 or DK280). The RCTUE/F processor can be installed in a DK424 or 
DK280 base cabinet. The expansion cabinets can be any combination of DK424 and DK280 - 
except the seventh expansion cabinet must be a DK424.
The DK280 expansion cabinet can only support six universal PCB slots in any possible 
configuration.
The DK424 expansion cabinet supports eight universal PCB slots only if the RCTUE/F is installed 
in a DK424 base cabinet and the MBJU jumper is removed from the DK424 base cabinet 
backplane.




  6SNU
  +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG 
SELECT = 
(Cabinet No. 1~7)Cabinet Type
(1 or 2)
1 (Base)
2 (1st Expansion)
3 (2nd Expansion)
4 (3rd Expansion)
5 (4th Expansion)
6 (5th Expansion)
7 (6th Expansion) 1 only
SELECT = Cabinet No. (1~7)
CABINET = 1 or 2 (type)
Type 1 (DK424)
Type 2 (DK280)Turn System Power OFF (5 sec) then ON.
or...
Run Program 91-2
Expansion Cabinet Universal PCB Slot Availability
Case 1
RCTUE/F in DK424 Base Cabinet with MBJU removed
Case 2
RCTUE/F in DK280 Base Cabinet
Expansion Cabinet (max 6)Universal PCB Slots
DK424 1~8 available
DK280 1~6 available
Expansion Cabinet (max 5)Universal PCB Slots
DK424 1~6 available
DK280 1~6 available 
						

							System & Station
Program 04 – Station Logical Port [PDN] Assignment
3-12Strata DK Programming 5/99
Program 04 – Station Logical Port [PDN] Assignment
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:See [PDNs] in the record sheets
DK14 Record Sheet
 
1. Supports a Digital Telephone or a DDCB Door Phone Control Box.
2. Supports Alternate Background Music (BGM).
DK40i Record Sheet
Important!Refer to Chapter 2 – DK40i Configuration before installing PCBs in slots 15~18.




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Physical 
Ports Modular Jack 
Location RecordLogical 
Ports [PDNs]
(Initialized)Port Type for Different Base Configurations
KSU1st QCDU22nd QCDU2QSTU2
000 000
(10)
4 - Digital 
Telephone 
Ports 001 001
(11)
002
10021(12)
003
10031(13)
004 004
(14)2 -Digital 
Telephone 
Ports 005 005
(15)
006 006
(16)2 - Digital 
Telephone 
Ports 007 007
(17)
008 008
(18)2 - Standard 
Telephone 
Ports 009
20092(19)




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
SELECT = Station Logical Port Number(s)
(see table below)[PDN] (1~4 digits)
SELECT = Station Logical Port Number(s)
(see table below)[PDN] (1~4 digits)Logical 
Ports 
(Initialized) 
						

							System & Station
Program 04 – Station Logical Port [PDN] Assignment
Strata DK Programming 5/993-13
System & Station
Expansion Slot Configuration Record1: Slot 15 ______  Slot 16 ______  Slot 17 ______  Slot 18 ______ 
1. Expansion slots 15~18: See DK40i Configuration tables in Chapter 2 of the Strata DK Installation and Maintenance Manual.
Physical 
PortsModular Jack 
Location RecordLogical Ports[PDNs]
(Initialized)
Port Type for Different Base Configurations
TCOU or TDDUTCOU, TBSU2 
or 
TDDU+KSTU2
2. TBSU circuits configured for line-side BRI.
TBSUTBSU+KSTU2
000 000
(10)
Base Slot 11
8 - Digital 
Telephone 
PortsBase Slot 11
8 - Digital 
Telephone 
PortsBase Slot 11
8 - Digital 
Telephone 
PortsBase Slot 11
8 - Digital 
Telephone 
Ports 001 001
(11)
002 002
(12)
003 003
(13)
004 004
(14)
005 005
(15)
006 006
(16)
007 007
(17)
008 008
(18)
Expansion 
Slots 15~18Base Slot 13Base Slot 12
3
TBSU CKT 1
2 Ports
3. If TBSU circuits that are set as station-side in Program *60, use two station ports per circuit. TBSU circuits that are set to line-side do not use 
station ports.
Base Slot 123
TBSU CKT 1
2 Ports
009 009
(19)4 KSTU2 Ports Base Slot 12
3
TBSU CKT 2
2 PortsBase Slot 12
3
TBSU CKT 2
2 Ports 010 010
(20)
011 011
(21)
012 012
(22)
Expansion 
Slots 15~18Expansion 
Slots 15~18Base Slot 13
4 KSTU2 Ports 013 013
(23)
014 014
(24)
015 015
(25)
016 016
(26)
Expansion 
Slots 15~18 017 017
(27)
018 018
(28)
019 019
(29)
020 020
(30)
021 021
(31)
022 022
(32)
023 023
(33)
024 024
(34)
025 025
(35)
026 026
(36)
027 027
(37) 
						

							System & Station
Program 04 – Station Logical Port [PDN] Assignment
3-14Strata DK Programming 5/99
DK424 Record Sheet




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor[PDN] Port RangeInitialized [PDNs]DISA PortReserved for Special Functions
RCTUA 000~031 200~231 039 032~039
RCTUBA/BB 000~079 200~279 089 080~089
RCTUC/D 000~239 200~239 249 240~249
RCTUE/F 000~335 100~435 344 336~349
Physica
l PortsModular Jack 
Location 
RecordLogical 
Ports [PDN]Cabinet and Slot 
NumberPhysica
l PortsModular Jack 
Location 
RecordLogical 
Ports [PDN]Cabinet and Slot 
Number
Cabinet: ______Slot: ______Cabinet: ______Slot: ______
Cabinet: ______
Slot: ______
Cabinet: ______
Slot: ______
Cabinet: ______Slot: ______Cabinet: ______Slot: ______
Cabinet: ______Slot: ______Cabinet: ______Slot: ______
SELECT = Station Logical Port Number(s)
Press [PDN] or Button LED 01 to erase (1~4 digits)