Home > Toshiba > Communications System > Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 418
    							System & Station
    Program 77-3 – Night Ringing Over PIOU External Page Zones
    Strata DK Programming 5/993-165
    System & Station
    Program 77-3 – Night Ringing Over PIOU External Page 
    Zones
    Processor Type:DK40i, All RCTUs
    Program Type:System
    Initialized Default:Zones 1~4 assigned to tenant 1
    Program 77-3 Overview
    Each tenants CO lines can be assigned to ring over selected PIOU external page zones during the 
    NIGHT mode. Lines must be allowed to Night Ring over External Page in Program 78 or Program 
    71 (1~3, Code #271) for this feature to work. Tenant assignments are made in Program 
    15. 
    
    
    
    
      6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
    TenantZone 1Zone 2Zone 3Zone 4
    Tenant 1 CO Lines
    Tenant 2 CO Lines
    Tenant 3 CO Lines
    Tenant 4 CO Lines
    Enter the tenant (1~4) to be assigned with 
    the zone entered in the preceding step.
    These assignments apply to ground and 
    loop start lines only; they do not apply to DID 
    and Tie lines. SELECT = 3
    Enter a PIOU external 
    page zone relay (1~4). 
    						
    							System & Station
    Program 77-4 – RSIU Open Architecture Interface (OAI) Data Output Assignments
    3-166Strata DK Programming 5/99
    Program 77-4 – RSIU Open Architecture Interface (OAI) 
    Data Output Assignments
    Processor Type:All RCTUs (Release 3.2 and above)
    Program Type:System
    Initialized Default:All LEDs are OFF
    Program 77-4 Overview
    This program is used to enable Caller ID, Automatic Number Identification (ANI), and/or Dialed 
    Number Identification Service (DNIS) Numbers (received) to be sent from the RSIU Open 
    Architecture Interface (OAI) port. The OAI port sends MIS data for ACD calls (only) along with 
    ANI, Caller ID and/or DNIS Numbers received on ACD calls depending on LED 01 and LED 02 
    option settings. ANI, Caller ID and/or DNIS numbers on non-ACD calls will not be sent out the 
    OAI port for non-ACD calls.
    
    
    
    
      6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
    LED/
    ButtonXLED ONLED OFF
    20
    19
    18
    17
    16
    15
    14
    13
    12
    11
    10
    09
    08
    07
    06
    05
    04
    03
    02DNIS Number will be sent from OAI port DNIS Number will not be sent from OAI port
    01Caller ID/ANI will be sent from OAI port Caller ID/ANI will not be sent from OAI port
    Light the LED Buttons that are 
    marked with an X in the table below.SELECT = 4 
    						
    							System & Station
    Program 77-4 – RSIU Open Architecture Interface (OAI) Data Output Assignments
    Strata DK Programming 5/993-167
    System & Station
    LED 01/LED 02: RSIU Open Architecture Interface (OAI) Data Output Assignments (Caller 
    ID/DNIS/ANI/OAI Output Options)
    Turn LED 01 ON if the OAI port should send Caller ID and/or ANI information for ACD calls and 
    LED 02 ON if the OAI port should send DNIS Number (not DNIS NAME) for ACD calls. LED 01 
    and 02 may be ON or OFF in any combination.
    RCTU PCB requires RKYS4 and RSIU to provide MIS, Caller ID, ANI, and DN information via 
    the system OAI port. 
    						
    							System & Station
    Program 78 – CO Line Special Ringing Assignments
    3-168Strata DK Programming 5/99
    Program 78 – CO Line Special Ringing Assignments
    Processor Type:DK14, DK40i
    Program Type:Station
    Initialized Default:All LEDs are OFF
    
    
    
    
      6SNU   +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
    ProcessorCO Line RangeProcessorCO Line Range
    DK14 001~004 RCTUBA/BB 001~048
    DK40i 001~012 RCTUC/D 001~144
    RCTUA 001~016 RCTUE/F 001~200
    Feature 
    NumberCodeFeature 
    DescriptionLine
    LED 0102030405060708091011121314151617181920
    13Ring Over External Page 
    during NIGHT mode
    21DISA CO Line during DAY 
    Mode
    2DISA CO Line during DAY2 
    Mode
    3DISA CO Line during NIGHT 
    Mode
    51Ring IMDU or RMDS
    1 Modem 
    during DAY Mode
    1. RMDS requires RSIU and is available with DK424 only, IMDU requires PIOU or PIOUS. See Programs 77-1 LED 14, and Program 76 for 
    RMDS. Only one built-in maintenance modem, IMDU or RMDS, will function at a time in DK424.
    2Ring IMDU or RMDS1 Modem 
    during DAY2 Mode
    3Ring IMDU or RMDS
    1 Modem 
    during Night Mode
    61Auto Attendant during DAY 
    Mode
    2
    2. If CO lines should ring telephones before the Auto Attendant answers, use Program 81~89 to assign telephones to ring. Do not assign telephones 
    in Program 81~89, if the Auto Attendant should answer on the first ring.
    2Auto Attendant during DAY2 
    Mode2
    3Auto Attendant during Night 
    Mode2
    CO Line
    Specify CO lines with LED Buttons as defined by the table 
    below. All LEDs with an X should be lit when finished.
    Press 
    6FUROO to advance or 3DJH to go back.
    After programming, press:
    Press 
    9R Os to turn all LEDs ON
    Press 9R Ot to turn all LEDs OFF
    0RGH + CO line number +  to display and advance Feature Number
    1, 2, 5, or 6
    Code 1~3 
    						
    							System & Station
    Program 78 – CO Line Special Ringing Assignments
    Strata DK Programming 5/993-169
    System & Station
    Program 78 Overview
    This program assigns ground/loop start CO lines:
    ©to ring over external page during night mode
    ©to be used with DISA features
    ©for direct access to IMDU/RMDS modem
    ©for Auto Attendant operation
    Feature 1: Ring Over External Page During Night Mode
    This program selects which ground/loop start CO lines will activate ringing over external paging 
    facilities during the NIGHT mode (for Tenants 1~4). The NT Relay on the PIOU, PIOUS, or 
    PEPU will also be activated if it is in the 1-second ON/3-seconds OFF mode.
    Feature 2: DISA CO Line Assignment
    This program assigns ground/loop start CO lines to be used with the Direct Inward System Access 
    (DISA) features. These lines may be set for DISA operation during the different system modes of 
    DAY, DAY2, and NIGHT. A line will switch to normal ringing after ten seconds if the outside 
    caller does not use the DISA feature. Normal function of these lines occurs for outgoing calls.
    NoteAn optional security code for DISA outgoing lines calls is available via Program 60-6. 
    This code should always be programmed when using DISA and built-in Auto Attendant to 
    prevent unauthorized calls through the DK system.
    Feature 5: Ring IMDU or RMDS Maintenance Modem
    The IMDU (DK40i and DK424 only) or RMDS (DK424 only) Remote Maintenance modem can 
    be directly accessed by incoming ground/loop start CO lines assigned in this Program. Different 
    alternatives are available for the system modes of DAY, DAY2, and NIGHT. If none of these are 
    selected, the IMDU or RMDS can still be reached by dialing a modem [DN] with the DISA feature 
    or by a Ring Transfer from the DSS console attendant or any other station. The IMDU or RMDS 
    modem must be enabled with Program 77-1, LED 14-ON.
    Feature 6: Built-in Auto Attendant CO Line Assignment
    This feature selects ground/loop start CO lines for Auto Attendant operation. There is no limit to 
    the number of lines which can be assigned with Auto Attendant. Different alternatives are 
    available for system modes DAY, DAY2, and NIGHT.
    Built-in Auto Attendant is not available for Tie, DID, ANI or DNIS lines on DK40i or DK424 and 
    is not available on any line of DK14.
    NoteAuto Attendant assignments 61~63 have priority over ACD assignments in Program 14-0. 
    						
    							System & Station
    Program 79 – Door Phone Ringing
    3-170Strata DK Programming 5/99
    Program 79 – Door Phone Ringing
    Processor Type:DK14, DK40i, All RCTUs
    Program Type:Station
    Initialized Default:All LEDs are OFF
    DP = Door Phone Program
    
    
    
    
      6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
    ProcessorPort RangeProcessorPort Range
    DK14 000~009 RCTUBA/BB 000~079
    DK40i 000~027 RCTUC/D 000~239
    RCTUA 000~031 RCTUE/F 000~335
    FeatureLEDPorts
    Muted ring to busy DKT/EKT20
    19
    18
    17
    16
    15
    14
    13
    Door phone 4C Ring DP1212
    Door phone 4B Ring DP1111
    Door phone 4A Ring DP1010
    Door phone 3C Ring DP99
    Door phone 3B Ring DP88
    Door phone 3A Ring DP77
    Door phone 2C Ring DP66
    Door phone 2B Ring DP55
    Door phone 2A Ring DP44
    Door phone 1C Ring DP33
    Door phone 1B Ring DP22
    Door phone 1A Ring DP11
    Light the LED Buttons that are marked with an X in 
    the table below.SELECT = Port Number
    Enter the port number having 
    Door Phone Ringing assigned.
    To specify a port range, enter 
    XXX
    
    XXX (low port 
     high port). 
    						
    							System & Station
    Program 79 – Door Phone Ringing
    Strata DK Programming 5/993-171
    System & Station
    Program 79 Overview
    This program assigns the door phone ringing feature to ports.
    LED 20: Muted Ring to Busy Electronic and Digital Telephone
    If all electronic and digital telephones are busy and a door phone button is pressed, a muted ring 
    tone can be sent to selected digital and electronic telephones, as defined with this program. (Only 
    the lowest port in the appropriate ringing group will mute ring.)
    LEDs 01~12: Door Phone Ring
    When a door phone button is pressed, selected digital and/or electronic telephones will ring as 
    assigned with this program. See Program 77-2 for an explanation of the door phone A, B, and C 
    numbering scheme. (Use Program 
    79 to assign [DN] button LEDs to flash on telephones that are 
    assigned to ring.)
    Door phones will not ring attendant consoles or standard telephones. Ringing door phones will 
    flash on idle console’s 
    $QVZHU buttons, but will not alert a console that is in the busy mode. See 
    Program 77-1 for door phone box port assignments. 
    						
    							System & Station
    Program *79 – Door Phone to [DN] Flashing Assignments
    3-172Strata DK Programming 5/99
    Program *79 – Door Phone to [DN] Flashing 
    Assignments
    Processor Type:DK14, DK40i, All RCTUs
    Program Type:Station
    Initialized Default:No [DNs] assigned to ring for any door phone
    Program *79 Overview
    This program assigns door phones to ring Directory Number buttons ([PDNs]/[SDNs] [PhDNs]) 
    when pressed and flash the [DN]’s LED. Each door phone can be assigned to flash one [DN]’s 
    LED and the [DN] can be assigned to appear and ring on up to 120 telephones.
    Program 79 must be used in conjunction with Program 
    79 to ring a telephone with a flashing 
    [DN], when the door phone button is pressed. See Program 77-1 for door phone control box port 
    assignments.
    Important!To allow a door phone to flash and ring, you must assign the [DN] to flash in 
    Program *79 and the telephone on which it appears must be assigned to ring in 
    Program 79.
    
    
    
    
      6SNU
      +ROG 6SNU+ROG 6SNU+ROG
    Processor[PDN] Port Range[PhDN] Port RangeProcessor[PDN] Port Range[PhDN] Port Range
    DK14 000~009 500~509 RCTUBA/BB 000~079 500~579
    DK40i 000~027 500~527 RCTUC/D 000~239 500~739
    RCTUA 000~031 500~531 RCTUE/F 000~335 500~835
    Door Phone Number/LocationDoor Phone Box 
    NumberDoor Box Circuit 
    Number[DN] Port Reference 
    Number
    1
    11
    22
    33
    4
    21
    52
    63
    7
    31
    82
    93
    10
    41
    11 2
    12 3
    Enter a [DN] Port Reference
    (Port Number of the [DN] that should flash when the 
    door phone button is pressed.)
    [DN] = [PDN] or [PhDN] port (see Legend below)Door Box Number (1~4)
    Door Box Circuit Number (1~3) 
    						
    							System & Station
    Program 80 – EKT and DKT Ringing Tones (CO Line Calls)
    Strata DK Programming 5/993-173
    System & Station
    Program 80 – EKT and DKT Ringing Tones (CO Line 
    Calls)
    Processor Type:DK14, DK40i, All RCTUs
    Program Type:Station
    Initialized Default:Tone 1 is assigned to all ports
    Program 80 Overview
    External speakers and all electronic and digital telephones are paged by dialing: [DN] + . The
    $OO&DOO3DJH$&
     button is used to page all digital and electronic telephones only; external 
    speakers are not included when using the button.
    PESU/PEKU can be in any universal slot assigned in Program 19-1.
    CAUTION!To prevent system malfunction, DO NOT install the PESU in slot 18 of the 
    DK40i system.
    
    
    
    
      6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
    ProcessorPort RangeProcessorPort Range
    DK14 000~009 RCTUBA/BB 000~079
    DK40i 000~027 RCTUC/D 000~239
    RCTUA 000~031 RCTUE/F 000~335
    Ringing Tone (Code)Ringing Tone (Code)Ringing Tone (Code)
    Port 
    NumberTo n e  1  
    (1)To n e  2  
    (2)To n e  3  
    (3)Port 
    NumberTo n e  1  
    (1)To n e  2  
    (2)To n e  3  
    (3)Port 
    NumberTo n e  1  
    (1)To n e  2  
    (2)To n e  3  
    (3)
    Ringing Tone Code
    1 = Tone Option 1
    2 = Tone Option 2
    3 = Tone Option 3SELECT = Station Logical Port Number
    Enter the telephone port number for which 
    the ringing tone is being defined.
    To specify a port range, enter XXX
    
    XXX 
    (low port 
    
     high port).
    *Incoming Line Call distinctive ring tones apply to DID, ground, and 
    loop start CO lines.
    Ring tone for internal or [DN] calls, and Tie line incoming calls is 
    Ring Tone Option123
    Incoming Line Call* 500/640 Hz 1200/1500 Hz 800/1000 Hz
    Transferred Line Call 540/760 Hz 1300/1780 Hz 880/1180 Hz 
    						
    							System & Station
    Program *80 – Call Forward Station Ring Assignment
    3-174Strata DK Programming 5/99
    Program *80 – Call Forward Station Ring Assignment
    Processor Type:All RCTUs with Release 3.2 and above
    Program Type:Station
    Initialized Default:LED 01, 04, and 07 ON for all lines
    Program *80 Overview
    Sets the Call Forward (CF) ringing assignment for ground/loop CO line calls. The station that 
    controls CF should be the only station programmed to ring in the appropriate Ringing Assignment 
    Programs (81~89). This program does not apply to Tie, DID, DNIS, or ANI lines.
    Example application: A CO line call rings a CO line button on multiple stations, then Call 
    Forwards. CO line 001 is programmed to ring station 200, then after 12 secs., it delay rings 
    stations 201 and 202 (12 secs.). Then, CO line 001 will CF per station 203’s CF setting. If station 
    203 has CF-No Answer, CO line 001 will ring station 203, and then CF. If station 203 has CF-All 
    Calls, CO line 001 will not ring station 203, but will forward immediately.
    Programming for the above example:
    Program 39 - Put CO line 001 button on stations 200~203.
    Program 81 - Set CO line 001 to ring station 200 immediately.
    Program 82 - Set CO line 001 to Delay Ring station 201 and 202
    Program 83 - Set CO line 001 to Delay 2 Ring station 203.
    Program *80 - Set CO line 001 to CF during Delay 2 Ring assignment (LED 03 ON).
    Set station 203 to CF to Voice Mail. When CO line 001 rings, the call will forward per station 
    203’s CF (All Calls, No Answer, etc.) setting during the Delay 2 ring period. Note that only station 
    203 can be set to ring in the Delay 2 (Program 83) ring assignment to allow CF to operate. VM will 
    receive station 203’s VMID (set via code #656).
    
    
    
    
      6SNU
      +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
    ProcessorCO Line RangeProcessorCO Line Range
    DK14 NA RCTUBA/BB 001~048
    DK40i NA RCTUC/D 001~144
    RCTUA 001~016 RCTUE/F 001~200
    System 
    Ring ModeCall Forward Station 
    Ring AssignmentLEDCO Lines
    Night
    Delay 2 (89) 09
    Delay 1 (88) 08
    Immediate (87) 07
    Day 2
    Delay 2 (86) 06
    Delay 1 (85) 05
    Immediate (84) 04
    Day
    Delay 2 (83) 03
    Delay 1 (82) 02
    Immediate (81) 01
    LED buttons = ringing assignment in 
    which calls should Call ForwardSELECT = CO Line Number
    To specify a CO line range, enter 
    XXX
    
    XXX (low line 
     high line). 
    						
    All Toshiba manuals Comments (0)

    Related Manuals for Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual