Samsung Ht D5530k User Manual

							English 21
02 Connections
CAUTION
Do not insert any other card except the TX card dedicated to the product\
. 
If a different TX card is used, the product may be damaged or the card m\
ay not be removed 
easily.
Do not insert the TX card upside down or in the reverse direction.
   Insert the TX card when the product is turned off. Inserting the card wh\
en it is turned on may 
cause a problem.
  The wireless receiving antenna is built into the wireless receiver modul\
e. Keep it away from water 
and moisture.
For optimal listening performance, make sure that the area around the wi\
reless receiver module 
location is clear of any obstructions.
If no sound is heard from the wireless surround speakers, switch the mod\
e to Dolby Pro 
Logic II.
In 2-CH mode, no sound will be heard from the wireless surround speakers\
.
NOTE
Place the wireless receiver module at the rear of the listening position\
. If the wireless receiver module is 
too close to the product, some sound interruption may be heard due to in\
terference.
If you use a device such as a microwave oven, wireless LAN Card or any o\
ther device that uses 
the same frequency (2.4/5.8GHz) near the product, some sound interrupt\
ion may be heard due 
to interference.
The transmission distance from the product to the wireless receiver modu\
le is about 10m, but may 
vary depending on your operating environment. If a steel-concrete wall o\
r metallic wall is between 
the product and the wireless receiver module, the system may not operate\
 at all, because the radio 
wave cannot penetrate metal.
If the product doesn't make wireless connection, the system needs ID Set\
ting between the 
product and wireless receiver module. 
With the main unit turned off, press the remote control's 
"0" "1""3""5" number buttons and then turn on the unit.
 With the wireless receiver module 
turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds. 
And then power on the product (HT-D5500/HT-D5530/HT-D5550).
Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit
If you attach a Toroidal ferrite core to the power cord of the man unit,\
 it will help to prevent RF 
interference from radio signals.
Pull the fi xing tab of the Toroidal ferrite core to 
open it.
Make a loop twice in the main unit power cord.
Attach the Toroidal ferrite core to the main unit power 
cord as the fi gure shows and press it until it clicks.
!







✎




1.
2.
3.
FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
WIRELESS VIDEO OUT
AUX INSURROUNDSUBWOOFER CENTER FRONT
SURROUNDCOMPONENT OUTHDMI IN
HT-D5500_ELS_1226.indd   21 HT-D5500_ELS_1226.indd   21
2011-12-26    1:23:54
2011-12-26    1:23:54
 
						

							22 English
Connections
Connecting External Devices/your TV via HDMI
HDMI is the standard digital interface for connecting to devices such as\
 a TV, projector, DVD player, 
Blu-ray player, set top box, and more.
Because HDMI is all digital, you'll enjoy digital quality video and soun\
d as it was originally created, 
without the distortions that can be caused when digital content is conve\
rted to analogue.
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the bac\
k of the product to the 
HDMI IN jack on your TV.
 NOTE
Certain HDMI output resolutions may not work, depending on your TV.
After making the video connection, set the Video input source on your TV\
 to match the 
corresponding Video output (HDMI, Component or Composite) on your prod\
uct.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he TV SOURCE button 
on the remote control and select HDMI as the external source of the TV.
You must have an HDMI connection to enjoy videos with 3D technology.
A long HDMI cable may cause a screen noise. If this is the case, set Dee\
p Colour to Off in the 
menu.
✎





FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
WIRELESS VIDEO OUT
AUX INSURROUNDSUBWOOFER CENTER FRONT
SURROUNDCOMPONENT OUTiPod
HDMI OUT
DIGITALAUDIO INOPTICALHDMI INLAN
WIRELESS LANSPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
WIRELESSVIDEO OUTAUX IN
COMPONENT OUTiPodDIGITALAUDIO INLAN
HDMI OUT HDMI IN
DVD or Blu-ray Player SAT(Satellite/Set top box)
HT-D5500_ELS_1226.indd   22 HT-D5500_ELS_1226.indd   22
2011-12-26    1:24:00
2011-12-26    1:24:00
 
						

							English 23
02 Connections
HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI IN jack on the back\
 of the product to the 
HDMI OUT jack on your digital device.
Press the FUNCTION button to select H. IN1 or H. IN2 input.
The mode switches as follows : BD/DVD  D. IN   AUX   R. IPOD   W. IPOD   H. IN1   H. IN2   FM
HDMI Auto Detection Function
If you have connected your home cinema by HDMI cable, the home cinema's \
video output 
automatically switches to the HDMI mode when you turn it on. For availab\
le HDMI video resolutions, 
see page 31.
This function is not available if the HDMI cable does not support CEC.
HDMI connection description- HDMI outputs only a pure digital signal to the TV.
-  If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for prev\
enting BD/DVD content outputted 
via HDMI from being copied. It provides a secure digital link between a \
video source (PC, DVD. etc) and a 
display device (TV, projector. etc). Content is encrypted at the sourc\
e device to prevent unauthorized 
copies from being made.
CAUTION The Anynet+ function is supported only when an HDMI Cable is connected t\
o the HDMI OUT of 
the product.
1.
2.
•
•
•
!

HT-D5500_ELS_1226.indd   23 HT-D5500_ELS_1226.indd   23 2011-12-26    1:24:01
2011-12-26    1:24:01
 
						

							24 English
Connections
METHOD 1 : Component Video (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Co\
mponent video cable (not 
supplied) from the Component Video Output (PR, PB and Y) Jacks on the back of the product to the 
Component Video Input Jacks on your TV.
 NOTE
You can select from a variety of resolution settings such as 1080i, 720p\
, 576p/480p and 576i/480i, 
depending on the disc type. (See page 31)
The actual resolution may differ from the setting in the Setup menu if b\
oth Component and HDMI cables are 
connected. The resolution may also be different depending on the disc. (\
See page 31)
After making the video connection, set the Video input source on your TV\
 to match the corresponding Video 
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he  TV SOURCE button on the remote 
control and select COMPONENT as the external source of the TV.
In DVD playback, if both HDMI and Component jacks are connected and you \
select the Component 1080p, 
1080i, 720p or 576p/480p mode, the Display Setup menu will show the outp\
ut resolution as 1080p, 1080i, 
720p or 576p/480p in the menu. The resolution is actually 576i/480i.
METHOD 2 : Composite Video (GOOD QUALITY) 
Connect the supplied Video cable from the VIDEO OUT jack on the back of \
the product to the VIDEO 
IN jack on your TV.
NOTE
The VIDEO source is always output in 576i/480i resolution regardless of \
the resolution set in the Setup 
menu. (See page 31)
After making the video connection, set the Video input source on your TV\
 to match the corresponding 
Video output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV'\
s Video Input source.
If you have set the product's remote control to operate your TV, press t\
he TV SOURCE button on 
the remote control and select VIDEO as the external source of the TV.
CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs ma\
y be affected by 
copyright protection systems and the picture will be distorted on the te\
levision.
✎





✎



!

FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
SS VIDEO OUT
AUX INSURROUNDSUBWOOFER CENTER FRONT
SURROUNDCOMPONENT OUTSPEAKERS OUT
SPEAKER IMPEDANCE : 3SSAUX IN
Red
Yellow
METHOD 2
BlueGreen
METHOD 1
HT-D5500_ELS_1226.indd   24 HT-D5500_ELS_1226.indd   24
2011-12-26    1:24:01
2011-12-26    1:24:01
 
						

							English 25
02 Connections
Connecting Audio from External Components
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-T\
op Box).Connect the Digital Input (OPTICAL) on the product to the Digital Outp\
ut of the external digital 
component.
  Press the FUNCTION button to select D. IN input.The mode switches as follows : 
BD/DVD   D. IN   AUX   R. IPOD   W. IPOD   H. IN1   H. IN2   FM
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it\
's video output to a TV.
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.This system supports Digital sampling frequencies of 32 kHz of higher fr\
om external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which \
is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external\
 analogue component. 
Be sure to match connector colours.
 
Press the FUNCTION button to select AUX input.

 
The mode switches as follows : 
BD/DVD   D. IN   AUX   R. IPOD   W. IPOD   H. IN1   H. IN2   FM
NOTE
  
You can connect the Video Output jack of your VCR to the TV, and connect\
 the Audio Output jacks of 
the VCR to this product.
1.
2.
•
✎



1.•
2. •
✎

FM ANT
WIRELESS
VIDEO OUAUX IN
HDMI OUT
DIGITAL
AUDIO IN
OPTICAL
COMPONENT OUT
HDMI IN
VIDEO OUWIRELESS
FM ANT
HDMI OUT
COMPONENT OUT
HDMI IN
Optical Cable
(not supplied)
Audio Cable
 
(not supplied)
If the external analogue 
component has only one 
Audio Out, connect either  left or right.
Set-Top Box VCRWhite
Red
OPTICAL AUX
HT-D5500_ELS_1226.indd   25 HT-D5500_ELS_1226.indd   25
2011-12-26    1:24:02
2011-12-26    1:24:02
 
						

							26 English
Connections
Connecting to the Network
This product enables you to view network based services (See pages 62~7\
1) such as Smart Hub and
BD-LIVE, as well as receive software upgrades when a network connection \
is made. We recommend
using an Wireless router or IP router for the connection.
For more information on router connection, refer to the user manual of t\
he router or contact the router
manufacturer for technical assistance.
Cable Network
Using the Direct LAN Cable (UTP cable), connect the LAN terminal of th\
e product to the LAN 
terminal of your modem.
Set the network options. (See page 38)
NOTE
Internet access to Samsung’s software update server may not be allowe\
d, depending on the router 
you use or the ISP’s policy. For more information, contact your ISP (\
Internet Service Provider).
For DSL users, please use a router to make a network connection.
For the AllShare function, a PC must be connected in the network as show\
n in the fi gure.
1.
2.
✎



iPodHDMI OUT
DIGITALAUDIO IN
OPTICAL
LAN
WIRELESS LAN
iPodHDMI OUTDIGITALAUDIO IN
Router Broadband modem Broadbandservice
Or
Broadband modem
(with integrated router)
Broadband service
Networking with PC forAllShare function(See page 71)
HT-D5500_ELS_1226.indd   26 HT-D5500_ELS_1226.indd   26 2011-12-26    1:24:04
2011-12-26    1:24:04
 
						

							English 27
02 Connections
Wireless Network
You can connect to the network with a Wireless IP sharer.A wireless AP/IP router is required to make a wireless network connectio\
n. Connect the wireless
LAN adapter to the Wireless LAN Adapter on the rear panel of the product\
. 
Set the network options. (See page 38)
NOTE
This product is compatible with only Samsung's Wireless LAN Adapter. (n\
ot supplied) (Model name: 
WIS09ABGN).
-  The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung E\
lectronics retailer for purchasing.
You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n\
 is recommended for stable 
operation of the wireless network.)
Wireless LAN, by its nature, may cause interference, depending on the us\
e condition (AP performance, 
distance, obstacles, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not su\
pported.
When applying the security key for the AP (wireless IP sharer), only t\
he following is supported. Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, AES
For the AllShare function, a PC must be connected in the network as show\
n in the fi gure.
1.
2.
✎





1)
2)

iPod DIGITALAUDIO INOPTICAL
LAN
WIRELESS LANDIGITALAUDIO INiPodLAN
Wireless IP sharer
Wireless LAN Adapter
(not supplied)
Broadband service
Networking with PC for
AllShare function
(See page 71)
PC
Connecting the FM Antenna
Connect the FM antenna supplied to the FM 
ANTENNA Jack.
Slowly move the antenna wire around until you 
fi nd a location where reception is good, then 
fasten it to a wall or other rigid surface.
NOTE
  This product does not receive AM broadcasts.
1.
2.
✎

FM ANT
WIRWIR
FM Antenna (supplied)
HT-D5500_ELS_1226.indd   27 HT-D5500_ELS_1226.indd   27
2011-12-26    1:24:06
2011-12-26    1:24:06
 
						

							28 English
Setup
Initial Settings
Turn on your TV after connecting the product.
When you connect and turn on the product to a 
TV for the fi rst time, the Initial Settings screen 
appears.
Initial Settings | On-Screen Language
m Move    "  Enter    
Select a language for the on-screen displays. Българ\bки  Hrvatski  Čeština
 Dansk  Nederlands English
 Eesti  Suomi  Français
 Deutsch 
 \fλληνικά  Magyar
 Indonesia  Italiano 
à´	¯
Press the ▲▼◄► buttons to select the desired 
language, and then press the ENTER button.
Press the ENTER button to select Start.
Press the ▲▼ buttons to select the desired TV 
Aspect Ratio, and then press the  ENTER button. 
(See page 31)
Musical Auto Calibration screen will be displayed.
Plug the ASC microphone into the ASC IN jack 
on the product. (See page 35)
Press the ENTER button to select Start button.
Setting the Musical Auto Calibration function 
takes about 3 minutes.
Press the ▲▼ buttons to select the desired 
Network Settings : Wired, Wireless 
(General), WPS(PBC) or One Foot 
Connection, and then press the ENTER  
button. If you do not know the details of your 
Network Settings, press the BLUE (D) button 
on your remote instead to skip Network 
Settings here, fi nish the Initial Settings, and 
go to the Home menu.
If you selected a Network Settings, go to 
pages 38~41 for more information about the 
Network settings. When done, go to Step 8.
The Home menu appears. (For more 
information about the Home menu, please 
see page 29.)
1.
2.
3.
4.
5.
6.
7.
8.
Home Menu
 d WPS(PBC)
My Devices Internet Settings
VideosPhotos
Music
My Contents
Function
 NOTE
The Home menu will not appear if you do not 
confi gure the initial settings except as noted 
below.
If you press the BLUE (D) button during the 
Musical Auto Calibration/network setup, you 
can access the Home menu even if the 
network setup is not completed yet.
If you want to display the Initial Setting screen 
again to make changes, select the Initial 
Settings. (See page 42)
If you use an HDMI cable to connect the 
product to an Anynet+ (HDMI-CEC)-
compliant Samsung TV and 1.) You have set 
the Anynet+ (HDMI-CEC) feature to On in 
both the TV and the product and 2.) You have 
set the TV to a language supported by the 
product, the product will select that language 
as the preferred language automatically.
If you leave the product in the stop mode for 
more than 5 minutes without using it, a screen 
saver will appear on your TV. If the product is 
left in the screen saver mode for more than 20 
minutes, the power will automatically turn off.
•
✎





HT-D5500_ELS_1226.indd   28 HT-D5500_ELS_1226.indd   28 2011-12-26    1:24:07
2011-12-26    1:24:07
 
						

							English 29
03 Setup
Accessing the Settings Menu
DISC MENU MENU TITLE MENU
TOOLS
RETURN EXIT
INFO
TUNER
POPUP
DISC MENUTITLE MENU
TOOLSINFO
TUNER
POPUP1
2
4
3
1MENU Button : Press to move to the Home menu.
2RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confi rm a setting.
4EXIT Button : Press to exit the current menu.
To access the Settings menu and sub-menus, 
follow these steps:
Press the POWER button.
The Home Menu appears.
Home Menu
d WPS(PBC)
My Devices Internet Settings
VideosPhotos
Music
My Contents
5
6
2
4
3
Function1
1Selects My Devices.
2Selects Function.
3Selects My Contents.
4Selects Internet.
5Selects Settings.
6Displays the buttons available.
1.
•
Press the ◄► buttons to select  Settings, 
and then press the ENTER button.
Press the ▲▼ buttons to select the desired 
submenu, and then press the  ENTER 
button.
Press the ▲▼ buttons to select the desired 
item, and then press the ENTER button.
Press the EXIT button to exit the menu.
NOTE 
When the product is connected to a network, 
select Internet from the Home menu. 
Download the desired content from Samsung 
Apps. (See pages 69~71)
The access steps may differ depending on the 
menu you selected. 
The OSD (On Screen Display) may change in 
this product after you upgrade the software 
version.
2.
3.
4.
5.
✎



HT-D5500_ELS_1226.indd   29 HT-D5500_ELS_1226.indd   29 2011-12-26    1:24:10
2011-12-26    1:24:10
 
						

							30 English
Setup
Display
You can confi gure various display options such as 
the TV Aspect Ratio, Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc with 3D 
contents in 3D Mode.
SettingsDisplay
Audio
Network
System
Language
Security
General
Support3D Settings
HDMI Deep Colour 
: Auto
3D Settings
> Move    " Enter    ' Return
3D Blu-ray Playback Mode  : Auto
Screen Size  : 55  inch
3D Blu-ray Playback Mode
3D Blu-ray Discs are available in two formats: 
Blu-ray 3D and 3D only. You can choose to 
watch a Blu-ray 3D disc in 3D or 2D mode before 
playing the disc.
Auto : Automatically detect if a connected TV has 
3D capability and play a Blu-ray 3D disc in 3D or 
2D accordingly or a 3D only disc in 3D if the TV 
supports 3D. 3D only discs will not be played if 
your TV does not support 3D.
3D  3D : Play 3D only and Blu-ray 3D discs in 
3D mode at all times.
3D   2D : Play Blu-ray 3D discs in 2D mode at all 
times. 3D only discs will not be played.
NOTE
To stop a movie during 3D playback, press the 
STOP
(  ) button once. The movie stops and the 
3D mode option is de-activated.
To change a 3D option selection when you are 
playing a 3D movie, press the STOP
(  ) button 
once. The Blu-ray menu appears. Press the 
STOP
(  ) button again, then select 3D 
Settings in the Blu-ray menu.
•
•
•
✎

Depending on the content and the position of 
the picture on your TV screen, you may see 
vertical black bars on the left side, right side, or 
both sides.
Screen Size
Lets you enter the actual screen size of your TV so 
that the product can adjust the image according to 
the screen size and display an optimal 3D image.
(The maximum allowed screen size is 116 inches for 
this product.)
CAUTION
If you want to enjoy 3D content, connect a 
3D device (3D compliant AV receiver or TV) 
to the product’s HDMI OUT port using a 
high-speed HDMI cable. Put on 3D glasses 
before playing the 3D content.
The product outputs 3D signals only through 
HDMI cable connected to the HDMI OUT 
port.
As the video resolution in 3D play mode is 
fi xed according to the resolution of the 
original 3D video, you can not change the 
resolution to your preference.
Some functions such as BD Wise, screen 
size adjustment, and resolution adjustment 
may not operate properly in 3D play mode.
Stay at least three times the width of the 
screen from the TV when watching 3D 
images. For example, if you have a 46 inch 
screen, stay 138 inches (3.5 meters) from 
the screen.
-  Place the 3D video screen at eye level for  the best 3D picture.
When the product is connected to some 3D 
devices, the 3D effect may not function 
properly.

!






HT-D5500_ELS_1226.indd   30 HT-D5500_ELS_1226.indd   30 2011-12-26    1:24:12
2011-12-26    1:24:12