NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual
Have a look at the manual NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 4 NDA-24282 Pag e 6 2 Revision 1.0 PA-AL16 (ALMC) SW4 1OFF×Alarm Bus Fixed 2OFF×Alarm Bus Fixed 3OFF×Alarm Bus Fixed 4OFF×Alarm Bus Fixed SW5 1 ON×Fixed 2OFF×Fixed 3OFF×Fixed 4ON For ACDP Dual System Configuration OFF For ACDP Single System Configuration SW6 1OFF×Alarm Bus Fixed 2OFF×Alarm Bus Fixed SWITCH NAMESWITCH NO.SETTINGSTANDARD SETTINGMEANING ON1234 ON1234 12ON
NDA-24282 CHAPTER 4 Page 63 Revision 1.0 PA-AL16 (ALMC) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS APM 20 MB UP: Circuit card make busy DOWN:Circuit card make idle EMASUP CPUSEL Middle = ACDP Dual System Down = ACDP Single System MG (SW3) 0 = Single CPU Systems 9 = Multi CPU Systems SW0 SW1 2 and 4 ON (Fixed) SW2 SW4 Alarm Bus SW5 4 ON = Dual ACDP 4 OFF = Single ACDP SW6 Alarm BusON ON ON 0 9 ON 1234 ON 1234 12ON ON 1234 ON 1234 12 ON
CHAPTER 4 NDA-24282 Pag e 6 4 Revision 1.0 PH-PC21 (APINT) PH-PC21 (APINT) 1. Function This circuit card is an inter-processor interface card and is used only for the Module Type ACD. The card provides FIFO for mutual I/O bus connections for processor communication between the system CPU and the ACDP. 2. Mounting Location/Condition The mounting location of this circuit card and the condition related to mounting are shown below. GATE CPU MEMECPYGATE CPU MEMAPINT APINT ACD Module 8-bit I/O Bus Extended 8-bit I/O Bus TSW, INT 8-bit I/O Bus 32-bit MEM Bus Position within the system 00 01 02 03 04 Mounting Module LPRJ-A PH-PC27 PH-PC27 PH-PC27 Note CPRAC-0 CPRAC-1 Note:This circuit card is mounted in any one of Slot No. 00~02.
NDA-24282 CHAPTER 4 Page 65 Revision 1.0 PH-PC21 (APINT) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. 4. Lamp Indications The contents of lamp indications of this circuit card are shown in the table below. 5. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. LAMP NAME COLOR STATE OPE/MBGreen Remains lit while this circuit card is operating. Red Lights while this circuit card is in make-busy state. CLKALM Red Lights when a failure has occurred to clocks for I/O bus synchronization. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING MBUP Circuit card make busy. DOWN Circuit card make idle. CLKALM OPE/MB MB SW01 AP0 AP1
CHAPTER 4 NDA-24282 Pag e 6 6 Revision 1.0 PH-PC21 (APINT) SW01ONWhen using this circuit card in the ACDP of single-system configuration or when connecting this circuit card to No. 0 system of the ACDP of dual-system configuration. OFFWhen connecting this circuit card to No. 1 system of the ACDP of dual-system configuration. 2ON×Fixed 3ONWhen the ACDP is provided by single-system configuration. OFFWhen the ACDP is provided by dual-system configuration. 4OFF×Fixed 5OFF×Fixed 6ON 7OFF 8ON SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING SW0-6 SW0-7 SW0-8 DEFINITION OF SOFTWARE TYPE ON ON OFFTo be used in ACD Module Type (Single- System Configuration) OFF ON OFFTo be used in ACD Module Type (Dual- System Configuration) Others Not used
NDA-24282 CHAPTER 4 Page 67 Revision 1.0 PH-PC21 (APINT) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS LPRJ-A 00 01 02MB UP: Circuit card make busy DOWN: Circuit card make idle SW0 ON ON 1234567 8
CHAPTER 4 NDA-24282 Pag e 6 8 Revision 1.0 PA-PC56-A (COPY) PA-PC56-A (COPY) 1. Function This circuit card provides the function to copy the contents of the RAM of both the standby (ST-Y) system and the active (ACT) system so that the contents of the RAM of both system may be always coinciding with each other. 2. Mounting Location/Condition The mounting locations of this circuit card and the conditions related to mounting are shown below. This circuit card is not used when the ACDP is provided in a single-system configuration. CPUCPU COPYCOPY CRAMCRAM IOC APM ALMC RS-232C (Non-protocol) Position within the system (ACDP) (ACDP) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mounting Module APM PA-PC56-APA-PC56-A For No.1 systemFor No.0 system
NDA-24282 CHAPTER 4 Page 69 Revision 1.0 PA-PC56-A (COPY) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. 4. Lamp Indications The contents of lamp indications of this circuit card are shown in the table below. LAMP NAME COLOR STATE OPE Green Remains lit while this circuit card is operating in ACT state. COPY Green Remains lit while this circuit card is operating in COPY mode. OPE SREQ SW0MB MBS1 COPY MBS0
CHAPTER 4 NDA-24282 Pag e 7 0 Revision 1.0 PA-PC56-A (COPY) 5. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING MBUP Circuit card make busy. DOWN Circuit card make idle. SREQUP Separate mode request. DOWN Separate mode request cancel (Copy mode). SW01ONTo be set in the case of System No. 0. (To be mounted in Slot No. 08 of APMA.) OFFTo be set in the case of System No. 1. (To be mounted in Slot No. 17 of APMA.) 2OFF× 3OFF× 4OFF× 5ON× 6ON× 7ON× 8ON× Fixed
NDA-24282 CHAPTER 4 Page 71 Revision 1.0 PA-PC56-A (COPY) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS APM-A\E 08 17MB UP: Circuit card make busy DOWN:Circuit card make idle SREQ SW0 1 ON = System No. 0 1 OFF = System No. 1ON ON ON 12345678