NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual
Have a look at the manual NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 4 NDA-24282 Pag e 1 22 Revision 1.0 PA-16ELCH (16ELC) Figure 4-9 Connecting Route Diagram NEAX2400 IMS A0MDF Rosette A0 B0 B0ELC Dterm
NDA-24282 CHAPTER 4 Page 123 Revision 1.0 PA-16ELCH (16ELC) Switch Setting Sheet MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS PIMU-A SW0 MB DOWN Circuit card make idle.ON 12 3 45678
CHAPTER 4 NDA-24282 (E) Pag e 1 24 Revision 1.0 PA-16ELCJ (16ELC) PA-16ELCJ (16ELC) 1. Function This circuit card is a line circuit card which supports the interface of 16 circuits or eight circuits of a 2W- Digital Terminal based on TCM transmission system (Time Compression Multiplex). This circuit card can be used as an eight-circuit voice/data digital line (8DLC Mode) and a 16-circuit voice only digital line circuit (16ELC Mode), and can be connected to any D term of the Dterm Series III. Differences in operations by mode are shown below. NO. OF CIRCUITS NO. OF TIME SLOTSDATA COMMUNICA- TION FUNCTIONREMARKS 8DLC Mode 8 Circuits 16 Time Slots Provided 16ELC Mode 16 Circuits 16 Time Slots Not Provided Dterm 0 D term 7 D term 8 D term 15 Note 16ELC 16ch COT MEM CPUC.O. Line Position within the SystemINT T S W Note:In 8DLC mode the circuit card is accommodated to Dterm 0~7.
NDA-24282 (E) CHAPTER 4 Page 125 Revision 1.0 PA-16ELCJ (16ELC) 2. Mounting Location/Condition The mounting locations of this circuit card and the conditions related to mounting are shown below. (a) When this circuit card is mounted in PIMJ (b) When this circuit card is mounted in PIMK Mounting Module PIMU-A 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Note:Indicates universal slots for line/trunk circuit cards. Mounting Module PIMK 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Note:Indicates universal slots for line/trunk circuit cards.
CHAPTER 4 NDA-24282 (E) Pag e 1 26 Revision 1.0 PA-16ELCJ (16ELC) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps and switches on this circuit card is shown below. 4. Lamp Indications The contents of lamp indications of this circuit card are shown in the table below. Note:When the PALM lamp lights red, observe the following instructions. i) Identify the location where any in-house wires have a short circuit as to all lines which belong to the PA-16ELCJ card whose PALM is on. ii) Repair the short-circuited wires of the associated D term. iii) Disconnect the Dterm from the rosette, then leave it disconnected for at least 1 minute. iv) Connect the Dterm again. LAMP NAME COLOR STATE OPEGreen Remains lit while on-line operations are normal. OFF Off when on-line operations are abnormal. PALM Red Lights when more than one power supply circuit are abnormal. Note OFF Off when all the power supply circuits are normal. BL0 BL15Green Lights when the corresponding circuit is busy. FlashFlashes when the corresponding circuit is in make-busy state or the system data is not assigned. OFF Off when the corresponding circuit is idle. OPE SW00 (MB) PALM BL15 BL0 SW01 ~
NDA-24282 (E) CHAPTER 4 Page 127 Revision 1.0 PA-16ELCJ (16ELC) 5. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. Note 1:APR-J/APA-J is an optional device to be connected to Dterm and provides interface for analog terminal. Note 2:By setting SW01-1 and SW01-7 as explained in the table below, either APR-J/APA-J or Data Adapter can be used. SWITCH NAMESWITCH NO.SETTINGSTANDARD SETTINGMEANING SW011 Note 1 Note 2 ON When APR-J/APA-J is not connected. OFFWhen APR-J/APA-J is connected. 2ON×Fixed ON OFF 3ON×Fixed in the system. OFF 4ON×Fixed in the system. OFF Dual Port Mode. 5ON×Fixed in the system. OFF 6ON×Fixed in the system. OFF 7ON 16ELC Mode OFF 8DLC Mode 8ON×Fixed in the system. OFF SW00 (MB)UP Circuit card make busy. DOWN×Circuit card make busy cancel. SW01-7 ON OFF SW01-1 ONUp to 16 circuits can be connected. Only voice is used.Up to 8 circuits can be connected. Simultaneous communications of voice and data (use of Data Adapter) can be done. Make this setting when using Data Adapter. OFFUp to 16 circuits can be connected. Simultaneous communications of voice and data (use of APR-J/APA-J) cannot be done. When either data or voice is used by changing over with APR-J/APA-J.Up to 8 circuits can be connected. Simultaneous communications of voice and data (use of APR-J/APA-J) can be done.
CHAPTER 4 NDA-24282 (E) Pag e 1 28 Revision 1.0 PA-16ELCJ (16ELC) 6. External Interface Accommodation of the LT connector leads of this circuit card and connecting route diagram are shown below. (a) LT Connector Lead Accommodation when this circuit card is mounted in PIMJ When the mode is 16ELC Mode/Single Port Mode. Figure 4-10 LT Connector Leads Accommodation of PIMU-A (1 of 3) LT Connector Accommodation 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 LT0 PIMJ LT Connector Name Slot No. LT1, 3, 5, 7, 9, 11 Connector Accommodated in *2 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A1 0 A1 1 A1 2 A1 3 A1 4 A1 5 Group No. LT1LT2LT3LT4LT5LT6LT7LT8LT9LT10LT11 01 0003 0205 0407 0609 0811 1001 0003 0205 0407 0609 0811 1015 14 13 1219 18 17 1623 22 21 2015 14 13 1219 18 17 1623 22 21 20 * 1 Highway Block01267834591011 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT0, 2, 4, 6, 8, 10 Connector Accommodated in *1 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 PWR* 1 * 1 * 1 * 1 * 1 * 2 * 2 * 2 * 2 * 2 * 2 PWR
NDA-24282 (E) CHAPTER 4 Page 129 Revision 1.0 PA-16ELCJ (16ELC) Figure 4-10 LT Connector Lead Accommodation of PIMU-A (2 of 3) LT Connector Accommodation 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 LT0 PIMJ LT Connector Name Slot No. LT1, 3, 5, 7, 9, 11 Connector B8 B9 B10 B11 B12 B13 B14 B15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25A8 A9 A10 A11 A12 A13 A14 A15 Group No. LT1LT2LT3LT4LT5LT6LT7LT8LT9LT10LT11 01 0003 0205 0407 0609 0811 1001 0003 0205 0407 0609 0811 1015 14 13 1219 18 17 1623 22 21 2015 14 13 1219 18 17 1623 22 21 20 * 3 Highway Block01267834591011 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT0, 2, 4, 6, 8, 10 Connector B0 B1 B2 B3 B4 B5 B6 B7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25A0 A1 A2 A3 A4 A5 A6 A7 PWR Accommodated in *3 PWR* 3 * 3 * 3 * 3 * 3
CHAPTER 4 NDA-24282 (E) Pag e 1 30 Revision 1.0 PA-16ELCJ (16ELC) When the mode is 8DLC Mode/Dual Port Mode. Figure 4-10 LT Connector Leads Accommodation of PIMU-A (3 of 3) LT Connector Accommodation 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 LT0 PWR PIMJ LT Connector Name Slot No. LT1, 3, 5, 7, 9, 11 Connector Accommodated in *2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Group No. LT1LT2LT3LT4LT5LT6LT7LT8LT9LT10LT11 01 0003 0205 0407 0609 0811 1001 0003 0205 0407 0609 0811 1015 14 13 1219 18 17 1623 22 21 2015 14 13 1219 18 17 1623 22 21 20 Highway Block01267834591011 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT0, 2, 4, 6, 8, 10 Connector Accommodated in *1 B0 B1 B2 B3 B4 B5 B6 B71 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25A0 A1 A2 A3 A4 A5 A6 A7 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT1, 3, 5, 7, 9, 11 Connector Accommodated in *3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 * 1 B0 B1 B2 B3 B4 B5 B6 B7A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7A0 A1 A2 A3 A4 A5 A6 A7 PWR* 1 * 1 * 1 * 1 * 1 * 2 * 2 * 2 * 2 * 2 * 2 * 3 * 3 * 3 * 3 * 3 * 3
NDA-24282 (E) CHAPTER 4 Page 131 Revision 1.0 PA-16ELCJ (16ELC) (b) LT Connector Lead Accommodation when this circuit card is mounted in PIMK When the mode is 16ELC Mode and the APR-J/APA-J is used. Figure 4-11 LT Connector Leads Accommodation of PIMK (1 of 3) LT Connector Accommodation 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT1, 3, 5, 8, 10 Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LT0, 2, 4, 6, 7, 9 Connector B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B151 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 LT0 PIMK LT Connector Name Slot No. Group No. LT1LT2LT3LT4LT5LT7LT8LT9LT10 03 0207 0611 1015 1419 1823 2215 14 13 1207 06 05 0415 14 13 1223 22 21 20 Highway Block012678 934510 11 LT6 23 22 21 2007 06 05 0415 14 13 1223 22 21 20 01 0005 0409 0813 1217 1621 2011 10 09 0803 02 01 0011 10 09 0819 18 17 16 19 18 17 1603 02 01 0011 10 09 0819 18 17 16 03 02 01 0007 06 05 04 8 910 11 4 56 7 2 3 0 1 * 1 Accommodated in *1Accommodation *2 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 * 1 * 1 * 1 * 1 * 1 * 2 * 2 * 2 * 2 * 2