NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual

							CHAPTER 4 NDA-24282
Pag e 4 2
Revision 1.0
SWITCH SETTING OF ACD CIRCUIT CARDS
2. EXPLANATION OF ACD CIRCUIT CARDS
This section explains each of the ACD circuit cards regarding the following items.
1. Function
Explanations are given about the functional outline and the purpose of each circuit card.
2. Mounting Location/Condition
The mounting location of each circuit card is illustrated with the mounting module name, slot number, etc.
Any conditions pertaining to mounting are also denoted.
3. Face Layout of Lamps, Switches, and Connectors
The locations of the lamps, switches, and connectors provided on each circuit card are illustrated by a face
layout.
4. Lamp Indications
Lamps equipped on each circuit card, their names, colors, and indication states are tabulated.
5. Switch Setting
Switches equipped on each circuit card, their names, switch numbers, setting and its meaning, standard set-
ting, etc. are tabulated.
6. External Interface
If the lead outputs of the circuit card are provided by an LT connector, the relation between the mounting
slots and the LT connector is illustrated by an LT Connector Lead Face Layout. Also, if the lead outputs are
provided by other than an LT connector or the lead outputs are provided by the circuit card front connector,
the connector lead accommodations and the connecting routes are illustrated.
A SWITCH SETTING SHEET showing module name, slot number, switch name, switch shape, etc. is provided
at the end of the explanation of each circuit card. 
						

							NDA-24282 CHAPTER 4
Page 43
Revision 1.0
PA - C P 5 3  ( C P U )
PA-CP53 (CPU)
1. Function
This circuit card is the CPU card (Central Processing Unit) which controls the ACD Circuit Card Type Sys-
tem. Using V60 microprocessor (32 bits), this CPU card provides programs and data memory. The card is
equipped with EPROM of 2MB and SRAM of 1MB, respectively.
GATE
I/O LOCAL BUS
RS-232C (Non-protocol)
ACD-MISEAPI
CPUACDP
LPRJ-A
ACD in IMX system (Circuit Card Type)
Position within the systemSYSTEM 
						

							CHAPTER 4 NDA-24282
Pag e 4 4
Revision 1.0
PA-CP53 (CPU)
2. Mounting Location/Condition
The mounting locations of this circuit card and the conditions related to mounting are shown below.
(a) When this circuit card is mounted in PIMA
(b) When this circuit card is mounted in PIMB
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module PIMU
Note:
 indicates the mounting locations of this circuit card.
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module PIMB
Note:
 indicates the mounting locations of this circuit card. 
						

							NDA-24282 CHAPTER 4
Page 45
Revision 1.0
PA - C P 5 3  ( C P U )
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
Note:When this circuit is used only as ACDP, PA-CC98 card is not used and thus this card is operating normally
even if this lamp is lighting.
LAMP NAME COLOR STATE 
CPU OPE  Green Remains lit while this circuit card is operating. 
CLKA RedLights when a microprocessor operating clock failure has occurred in this circuit 
card. 
COPA Red Lights when a C-level infinite loop has occurred. 
LANA YellowLights when a major failure has occurred in PA-CC98 card or when this circuit 
card is not connected with PA-CC98 card. 
Note
DMWE Green Remains lit when the data memory in this circuit card is in write enable state. 
CPU OPE
MBR SW1
SW0SW2
CLKA 
COPA 
LANA 
DMWE
RESET
SENSE 
						

							CHAPTER 4 NDA-24282
Pag e 4 6
Revision 1.0
PA-CP53 (CPU)
5. Switch Settings
Standard settings of various switches on this circuit card are shown in the table below.
SWITCH
NAMESWITCH
NO.SETTINGSTANDARD
SETTINGMEANING
MBRUP Circuit card make busy request.
DOWN Circuit card make busy request cancel
RESET PUSH Starting of reset of this circuit card
SENSE5×On line (Normal Operation)
DClearing the data memory area at the time of 
initialization
SW01OFF×Fixed
2OFF×Fixed
3OFF×Fixed
4OFF×Fixed
5OFF×Fixed
6OFF×Fixed
7OFF×Fixed
8ON×Fixed
SW11OFF×Fixed
2OFF×Fixed
3OFF×Fixed
4OFF×Fixed
5OFF×Fixed
6ON×Fixed
7ON IMX
OFF ICS
8OFF×Fixed 
						

							NDA-24282 CHAPTER 4
Page 47
Revision 1.0
PA - C P 5 3  ( C P U )
SW21ON×Internal NMI possible
OFF Internal NMI inhibited
2ON×Data Memory Write Protect cancel
OFF Data Memory Write Protect controllable
3ON Data Memory Write inhibited
OFF×Data Memory Write controllable
4ON When connecting PA-CC98 card
OFF When not connecting PA-CC98 card
5OFF×Fixed
6OFF×Fixed
7OFF×Fixed
8OFF×Fixed
SWITCH
NAMESWITCH
NO.SETTINGSTANDARD
SETTINGMEANING 
						

							CHAPTER 4 NDA-24282
Pag e 4 8
Revision 1.0
PA-CP53 (CPU)
SWITCH SETTING SHEET
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
PIM any 
universal 
slotMBR UP: Circuit card make 
busy request
DOWN: Circuit card make 
busy request cancel
RESET
SENSE
SW0
SW1 7 = ON for IMX
7 = OFF for ICS
SW2 4 ON When connecting 
PA -C C 9 8
ON
ON
12345678
ON
12345678
ON
12345678 
						

							NDA-24282 CHAPTER 4
Page 49
Revision 1.0
PH-PC22 (EAPI)
PH-PC22 (EAPI)
1. Function
This circuit card is an I/O system functions integrated card to be used in the ACD Circuit Card Type System.
This card supports the following functions.
(a) APINT Function: For processor communications between the CPU of the System and ACDP card,
this circuit card provides FIFO for mutual I/O bus connections. 
(b) IOC Function: For ACD-MIS connection, this circuit card provides a serial interface which conforms
with RS-232C (two I/O ports).
2. Mounting Location/Condition
The mounting locations of this circuit card and the conditions related to mounting are shown below.
GATE
CPU
MEMECPYGA TE
CPU
MEMMISC EAPI
ACDPMISC
8-bit I/O Bus
RS-232C Extended 8-bit I/O Bus TSW, INT
8-bit I/O Bus
32-bit MEM Bus
Position within the system
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module CMA
PHPC-22 PHPC-22 PHPC-22
Note
Note:This circuit card is mounted in any one of Slot No. 02~04. 
						

							CHAPTER 4 NDA-24282
Pag e 5 0
Revision 1.0
PH-PC22 (EAPI)
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
00 01 02 03 04
Mounting Module LPRJ-A
PHPC-22
PHPC-22
PHPC-22
Note
CPRAC-0 CPRAC-1
Note:This circuit card is mounted in any one of Slot No. 00~02
IOC OPE 
CLKALM
OPE/MB
MB
SW0
SW01
SW11
MBR 
						

							NDA-24282 CHAPTER 4
Page 51
Revision 1.0
PH-PC22 (EAPI)
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
5. Switch Settings
Standard settings of various switches on this circuit card are shown in the table below.
LAMP NAME COLOR STATE
OPE/MB Green Remains lit while this circuit card is operating.
IOCOPE Red Remains lit while the non-protocol/RS-232C Port Controller is operating normally. 
CLKALM Red Lights when a clock failure has occurred.
SWITCH 
NAMESWITCH NO. SETTINGSTANDARD 
SETTINGMEANING
MBUP  Circuit card make busy request
DOWN Circuit card make busy cancel
MBRUPRequests the software to place the ACD-MIS 
Interface Port Controller into make-busy state.
DOWNCancels the request to place the ACD-MIS 
Interface Port Controller into make-busy state. 
(Circuit card operating state)
SW01OFF×
2OFF×
3OFF×
4OFF×
5OFF×
6ON×
7OFF×
8ON×
Fixed