NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual

							CHAPTER 4 NDA-24282 (E)
Pag e 1 62
Revision 1.0
PA-4DTLA (4DTL)
NEAX2400 IMS
B00MDF
G
R
A004DTLModular
JackDTE RS232
B
B10
Y
A10 
						

							NDA-24282 (E) CHAPTER 4
Page 163
Revision 1.0
PA-CC98 (ETHER)
PA-CC98 (ETHER)
Ethernet Controller
1. Functional Outline
In the NEAX2400 ICS OAI System, this circuit card supports the functions for interface between the CPU
(IP) circuit card and the external computer. If circuit card type, this circuit card is directly connected with
the CPU card (PA-CP53). If module type, being paired with PA-GT (MBB) card, it connects the Interface
Processor (IP) and the User Application Processor (UAP) through a LAN.
CPU (No.0 Sys) 
(PA-CP53)
ETHER 
(PA-CC98)
Ethernet
(a) If circuit card type
CPU (No.0 Sys) 
(PA-CP54)CPU (No.1 Sys) 
(PA-CP54)
MBB 
(PA-GT16)
ALMC 
(PA-AL16)
ETHER 
(PA-CC98)Ethernet
(b) If module type (dual system configuration) Memory Bus 
(No.0 System)Memory Bus 
(No.1 System) 
						

							CHAPTER 4 NDA-24282 (E)
Pag e 1 64
Revision 1.0
PA-CC98 (ETHER)
2. Circuit Card Mounting Locations/Conditions
The mounting locations and conditions of this circuit card are shown below.
(a) In the case of circuit card type
 When mounting in the PIMU-A
 When mounting in the PIMB
Mounting Module PIMU-A
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Note:      Indicates the mounting locations of this circuit card.
Mounting Module PIMB
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Note:      Indicates the mounting locations of this circuit card. 
						

							NDA-24282 (E) CHAPTER 4
Page 165
Revision 1.0
PA-CC98 (ETHER)
(a) In the case of module type
3. Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors equipped on this circuit card are shown below.
Mounting Module APM
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23PA-CC98
SW0
BUS LAN FUSE OPE
SW1ERR 
S2 S1 
S3
SW2 
						

							CHAPTER 4 NDA-24282 (E)
Pag e 1 66
Revision 1.0
PA-CC98 (ETHER)
4. Lamp Indications
The meaning of indication of each lamp on this circuit card is shown below.
5. Switch Setting
Each switch setting on this circuit card and its meaning are shown in the tables on the following pages.
The CC98 Internet address is set by using the AIPT MAT command. For ICS and IMX, Internet is set only
by the AIPT command. For HDS (IMG) configurations, the AIPT command is used for setting the Internet
address for software versions J04.7 and higher.
Contact NEC Personnel for Internet address settings in HDS software versions below J04.7.
Each CC98 card must have a unique MAC address. This MAC address allows each CC98 to be different
from each other and different from any other LAN system. The MAC address is twelve digits in length.
Switches SW0 and SW1 are used to set the lowest three digits. The remainder of the MAC address is fixed.
The Internet address set by AIPT is used with the MAC address to allow the CC98 to connect to LAN net-
works.
Note:If two or more CC98 cards are connected on the same LAN, each must have a unique MAC address.
LAMP COLOR MEANING OF INDICATION
OPE Green Remains lit while this circuit card is in operating status
ERRRed When a fault has occurred within this circuit card, this lamp lights or flashes to-
gether with lamp S1, S2, or S3 so as to specify the contents of the fault
Red
Flash
S1Green
FlashFlashes when data frame has been sent out onto the LAN
S2 Green Lights when this circuit card is ready to operate
S3 Green Remains lit while the power supply to this circuit card is on 
						

							NDA-24282 (E) CHAPTER 4
Page 167
Revision 1.0
PA-CC98 (ETHER)
SWITCHDIP SW 
No.SETTINGDEFAULT 
SETTINGMEANING
SW0
(8 DIP Switches)1ON Sets 0, corresponding to bit 0 of MAC address
OFF Sets 1, corresponding to bit 0 of MAC address
2ON Sets 0, corresponding to bit 1 of MAC address
OFF Sets 1, corresponding to bit 1 of MAC address
3ON Sets 0, corresponding to bit 2 of MAC address
OFF Sets 1, corresponding to bit 2 of MAC address
4ON Sets 0, corresponding to bit 3 of MAC address
OFF Sets 1, corresponding to bit 3 of MAC address
5ON Sets 0, corresponding to bit 4 of MAC address
OFF Sets 1, corresponding to bit 4 of MAC address
6ON Sets 0, corresponding to bit 5 of MAC address
OFF Sets 1, corresponding to bit 5 of MAC address
7ON Sets 0, corresponding to bit 6 of MAC address
OFF Sets 1, corresponding to bit 6 of MAC address
8ON Sets 0, corresponding to bit 7 of MAC address
OFF Sets 1, corresponding to bit 7 of MAC address
Note:For switch setting for MAC address, refer to [Reference] shown below in the
setting of SW1. For details of switch setting for Internet address, refer to the
AIPT command explained in Chapter 7, ”PBX and ACD Command Pro-
gramming”.
SW1
(8 DIP Switches)1ON Sets 0, corresponding to bit 8 of MAC address
OFF Sets 1, corresponding to bit 8 of MAC address
2ON Sets 0, corresponding to bit 9 of MAC address
OFF Sets 1, corresponding to bit 9 of MAC address
3ON Sets 0, corresponding to bit 10 of MAC address
OFF Sets 1, corresponding to bit 10 of MAC address
12345678
ON
12345678
ON 
						

							CHAPTER 4 NDA-24282 (E)
Pag e 1 68
Revision 1.0
PA-CC98 (ETHER)
SW1 (Continued)
4ON Sets 0, corresponding to bit 11 of MAC address
OFF Sets 1, corresponding to bit 11 of MAC address
5ON×Fixed
6ON×Fixed
7ON×Fixed
8ON×Fixed
[Reference]
Setting of MAC address
On LAN and TCP/IP, this circuit card can have the following 
addresses and ports.
MAC Address: 000032250xxxH (48 bits)
TCP Port Numbers: 16 port numbers of 1024 ~ 1039
The last 12 bits of MAC address must be set by switches 
SW0 and SW1 before starting up this circuit card.
(Ex.)
When MAC address is to be set to 000032250123H:
By dividing 12 bits into 4-bit units (refer to the table on the 
right side), and set the switches as shown below.
SW2
(Rotary SW)0Fixed setting (When operating)
SWITCHDIP SW 
No.SETTINGDEFAULT 
SETTINGMEANING
0H
1H
2H
3H
4H
5H
6H
7H
8H
9H
AH
BH
CH
DH
EH
FH
Relation between the value 
of 4 Bits and Switch Setting
Hex Switch Setting
0 = Fixed (not used) SW0SW1
12345678
ON
32
12345678
ON
10 
						

							NDA-24282 (E) CHAPTER 4
Page 169
Revision 1.0
PA-CC98 (ETHER)
MODULE SLOT SWITCH SWITCH SHAPE REMARKS
SW0
SW1
SW2Fixed for the system12345678ON
12345678ON
0 
						

							CHAPTER 4 NDA-24282 (E)
Pag e 1 70
Revision 1.0
PA-GT16 (MBB)
PA-GT16 (MBB)
Memory Bus Buffer
1. Functional Outline
This circuit card is used in the OAI module type for the NEAX2400 IMX and ICS OAI System. It is a circuit
card which repeats the memory bus on PA-CP54 (CPU) card side to ETHER (Ethernet Interface) gate card.
2. Circuit Card Mounting Locations/Conditions
Mounting Module APM
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23PA-GT16
CPU (No.0 Sys) 
(PA-CP54)CPU (No.1 Sys) 
(PA-CP54)
MBB 
(PA-GT16)
ALMC 
(PA-AL16)
ETHER 
(PA-CC98)Ethernet
Position within the system Memory Bus (No.0 System) Memory Bus (No.1 System) 
						

							NDA-24282 (E) CHAPTER 4
Page 171
Revision 1.0
PA-GT16 (MBB)
3. Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors equipped on this circuit card are shown below.
4. Lamp Indications
The meaning of indication of each lamp on this circuit card is shown below.
LAMP COLOR MEANING OF INDICATION
OPE Green Remains lit while this circuit card and ETHER card are normally operating
LAN ALM RedLights when the processor in ETHER card has become faulty or when ETHER 
card is not correctly connected with this circuit card
SW0
BUS OPE
SEG
MB
LAN ALM 
MBRQ