NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual
Have a look at the manual NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 4 NDA-24282 Pag e 8 2 Revision 1.0 PA-ME34 (CRAM) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS APM-A\E 06 08 19DMWDK SW0 SW1ON ON 12345678 ON 12
NDA-24282 CHAPTER 4 Page 83 Revision 1.0 PA-IO02-A (IOC) PA-IO02-A (IOC) 1. Function This circuit card is an I/O card (input/output control card) and provides a serial interface function by which the CPU performs mutual communications with the ACD-MIS conforming with the RS-232C Interface. 2. Mounting Location/Condition The mounting locations of this circuit card and the conditions related to mounting are shown below. CPUCPU COPYCOPY CRAMCRAM IOC APM-A\E ALMC RS-232C (Non-protocol) Position within the system (ACDP) (ACDP) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mounting Module APM-A\E PA-IO02-A PA-IO02-APA-IO02-A
CHAPTER 4 NDA-24282 Pag e 8 4 Revision 1.0 PA-IO02-A (IOC) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. 4. Lamp Indications The contents of lamp indications of this circuit card are shown in the table below. LAMP NAME COLOR STATE OPE Green Remains lit while this circuit card is operating in ACT mode. ON LINE1 Green Remains lit while PORT 1 is in on-line state. ON LINE0 Green Remains lit while PORT 0 is in on-line state. OP E MB SW3ON LINE1 ON LINE0 MB REQ SW0 SW01SW11 SW02 SW12 OFF LINE
NDA-24282 CHAPTER 4 Page 85 Revision 1.0 PA-IO02-A (IOC) 5. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING MB UP Circuit card make busy. DOWN Circuit card make idle. MB REQ UP Circuit card make busy. DOWN Circuit card make idle. OFF LINE UP Setting is inhibited. MIDDLE×Fixed. DOWN Setting is inhibited. SW0 1 2 3OFF× 4OFF× 5OFF× 6OFF× 7OFF× 8OFF× SW3 1 OFF× 2OFF× 3OFF× 4OFF× SW0-1 SW0-2 SETTING OF IOC EQUIPMENT NUMBER OFF OFF Sets IOC Equipment Number 0. OFF ON Sets IOC Equipment Number 1. ON OFF Sets IOC Equipment Number 2. Fixed Fixed
CHAPTER 4 NDA-24282 Pag e 8 6 Revision 1.0 PA-IO02-A (IOC) SW1 (for Port 0) SW11 (for Port 1)1 2 3 4 5 6ON×Data Length: 7 bits OFF Data Length: 8 bits 7ON×Stop Bit: 1 bits OFF Stop Bit: 2 bits 8ONData store into the send-side buffer of the port is disabled. OFF×Data of max. 64 kbytes are to be stored into the send-side buffer of the port. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING SW01-1 SW11-1SW01-2 SW11-2SW01-3 SW11-3DATA TRANSMISSION SPEED (BPS) SETTING ON ON ON 300 bps ON ON OFF 600 bps ON OFF ON 1200 bps ON OFF OFF 2400 bps OFF ON ON 4800 bps OFF ON OFF 9600 bps SW01-4 SW11-4SW01-5 SW11-5PARITY SETTING ON ON ODD Parity ON OFF EVEN Parity (standard setting) OFF OFF No Parity
NDA-24282 CHAPTER 4 Page 87 Revision 1.0 PA-IO02-A (IOC) Note: When setting SW02-7/SW12-7 to ON, set SW02-1/SW12-1 to ON, also. SW02 (for Port 0) SW12 (for Port 1)1ON×PB terminal becomes minus (-) when the port terminal is busy. OFFPB terminal becomes plus (+) when the port terminal is busy. 2ON×Sets the ER terminal of the port to Always ON. OFFControls ON/OFF of the ER terminal of the port by the CPU. 3ON DR signal lead is not to be used to the port. OFF×DR signal lead is to be used to the port. 4ON×CD signal lead is not to be used to the port. OFF CD signal lead is to be used to the port. 5ON CS signal lead is not to be used to the port. OFF×CS signal lead is to be used to the port. 6ON CI signal lead is not to be used to the port. OFF×CI signal lead is to be used to the port. 7ON×PB signal lead is not to be used to the port. Note OFF PB signal lead is to be used to the port. 8OFF×Not used. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING
CHAPTER 4 NDA-24282 Pag e 8 8 Revision 1.0 PA-IO02-A (IOC) 6. External Interface The RS connector leads accommodation of this circuit card is shown below. Figure 4-1 RS Connector Leads Accommodation 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 RS0 APM-A\E Slot No. E E E E E CI0 E E E E E E E E E E E CI1 E E E E E E EXTA1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PA-IO02-A RS Connector Leads Accommodation RS0 Connector SD0 RD0 RS0 CS0 DR0 SG0 CD0 ER0 PB0 SP00 SP10 SP20 SD1 RD1 RS1 CS1 DR1 SG1 CD1 ER1 PB1 SP01 SP11 SP21 EXTB
NDA-24282 CHAPTER 4 Page 89 Revision 1.0 PA-IO02-A (IOC) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS APM-A\E 04 MB UP: Circuit card make busy. MB REQ DOWN:Circuit card make idle. OFF LINE SW0 SW3 SW01 SW02 SW11 SW12ON ON ON ON 12345678 ON 1234 ON 12345678 ON 12345678 ON 12345678 ON 12345678
CHAPTER 4 NDA-24282 Pag e 9 0 Revision 1.0 PH-BS16 (PBI) PH-BS16 (PBI) 1. Function This circuit card provides an interface by which the ACDP performs inter-processor communications with another Processor via the Processor Bus (P-BUS) under control of the ACDP (PA-CP54 card). Also, this circuit card is connected with the Maintenance Bus (M-BUS) and provides functions that allow the SP (System Processor) to read out status or fault information of the ACDP and that cause the ACDP to set make- busy or perform initialization. 2. Mounting Location/Condition The mounting locations of this circuit card and the conditions related to mounting are shown below. CPU (ACDP) PBISP0 SPCSP1 SPC MEM M-BUS No.0 M-BUS No.1 P-BUS No.0 P-BUS No.1To other processor To other processor Position within the system 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mounting Module APM-A\E PH-BS16PH-BS16 For No. 1 system For No. 0 system
NDA-24282 CHAPTER 4 Page 91 Revision 1.0 PH-BS16 (PBI) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. OPE MB PWRALM ACT EQBY PBIH PBIL B-OPE0 B-OPE1 TR BSY RV BSY M-OPE