NEC Neax 2400 Imx Business Features And Specifications

							NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 81
Call Forwarding - Busy Line - DtermC-2D
C-2D  Call Forwarding - Busy Line - Dterm
General Description
This feature permits a call to a busy station to immediately be forwarded to a predesignated station, or to the
Attendant. CALL FORWARDING - BUSY LINE - Dterm may be set or cancelled by the user for all multi-line
appearances on the Dterm. Additionally, a single line user may set CALL FORWARDING - BUSY LINE - Dterm for
all sub-lines on the Dterm.
Operating Procedure
To set CALL FORWARDING - BUSY LINE - Dterm: 
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Press the CALL FORWARDING - BUSY LINE FORWARD-BY key; receive special dial tone.
3. Dial the desired target telephone number; receive service set tone. The LED of the associated feature key
lights and the LCD displays:
Target Station
4. Replace the handset or press the SPEAKER key.
5. If the target station is the Attendant Console, the LCD displays:
To monitor CALL FORWARDING - BUSY LINE - Dterm:
1. Press the CALL FORWARDING - BUSY LINE FORWARD-BY feature key. The LCD displays:
Target Station
2. If the target station is the Attendant Console:
To cancel CALL FORWARDING - BUSY LINE - Dterm:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Press the FORWARD-BY key; receive service set tone. The LCD displays:
3. The associated LED goes out.
4. Replace the handset or press the SPEAKER key.FORWARD SET
XXXX
                   (Time Display) 
FWD SET 
                  (Time Display)       
FORWARD
XXXX
                   (Time Display) 
FWD SET 
                   (Time Display)      
FORWARD CANCEL
                  (Time Display)  
						

							NEAX2400 IMX Business Features and Specifications
Page 82NDA-24221, Issue 3
C-2D Call Forwarding - Busy Line - Dterm
Operating Procedure (cont’d)
To set CALL FORWARDING - BUSY LINE - Dterm to a Dterm multi-line:
1. Press the multi-line key for which CALL FORWARDING - BUSY LINE - Dterm feature is to be set.
2. Lift the handset or press the SPEAKER key; receive special dial tone.
3. Press the CALL FORWARDING - BUSY LINE “FORWARD-BY” feature key; receive special dial tone.
4. Dial the desired target telephone number; receive service set tone. The LCD displays:
Target Station
5. The LED of the associated feature key lights on the D
term for which this multi-line is a MY Line.
6. If the target station is the Attendant, the LCD displays: 
7. Replace the handset or press the SPEAKER key.
To monitor CALL FORWARDING - BUSY LINE to a Dterm multi-line:
1. Press the multi-line key for which CALL FORWARDING - BUSY LINE - Dterm is to be monitored.
2. Press the FORWARD-BY key. The LCD displays:
Target Station 
If the target station is the Attendant Console:
To cancel CALL FORWARDING - BUSY LINE to a Dterm multi-line:
1. Press the multi-line key for which CALL FORWARDING - BUSY LINE - Dterm feature is to be cancelled.
2. Lift the handset or press the SPEAKER key; receive dial tone.
3. Press the FORWARD-BY key; receive service set tone. The LED of the associated feature key will go out
on the D
term for which this multi-line is a MY Line. The LCD displays:
4. Replace the handset or press the SPEAKER key.
Service Conditions
1. This feature may be set and cancelled by the user or the Attendant.
2. CALL FORWARDING - BUSY LINE - D
term data remains programmed, even if the system is
reinitialized or a power failure occurs.FORWARD SET XXXX
                   (Time Display) 
FWD SET OPR
                   (Time Display) 
FORWARD
XXXX
                  (Time Display) 
FWD SET OPR
                  (Time Display) 
FORWARD CANCEL
                 (Time Display)  
						

							NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 83
Call Forwarding - Busy Line - DtermC-2D
Service Conditions (cont’d)
3. This feature is assigned to stations through CLASS OF SERVICE - INDIVIDUAL [C-15] programming
in System Data.
4. There is no limitation to the number of stations that can set CALL FORWARDING - BUSY LINE [C-2]
simultaneously.
5. CALL FORWARDING - BUSY LINE - D
term may also be accessed via the dial pad or SPEED CALLING
- ONE TOUCH [S-22].
Note:If this feature is accessed via the dial pad, it must be cancelled via the dial pad.
6. If separate access codes are programmed into System Data for CALL FORWARDING - DONT
ANSWER [C-3] and CALL FORWARDING - BUSY LINE [C-2], separate feature keys must be
programmed on each D
term to equip it with both features.
7. CALL FORWARDING - BUSY LINE - D
term can be provided on a tenant and/or an individual station
basis.
8. Call Forwarding on a tenant basis allows any incoming calls, which encounter a busy condition, to be
forwarded to a predetermined station or the ATTENDANT CONSOLE [A-3].
9. Individual CALL FORWARDING - BUSY LINE - D
term supersedes tenant basis CALL
FORWARDING.
10. The display of an intermediate station on a D
terms LCD panel may be allowed or denied according to
system data. This assignment is done on a system basis. The LCD displays:
Intermediate Station Calling/Called Party
Note:When the telephone number of the intermediate or calling/called station exceeds 8 digits, the last 8 digits are
displayed. However, a maximum of 16 digits calling/called telephone number can be displayed on the middle line of
LCD depending on the System Data.
11. CALL FORWARDING - BUSY LINE - Dterm supersedes STATION HUNTING [S-7, 8, 9].
12. The operator answering a forwarded call can identify the called number on the ATTENDANT CONSOLE
[A-3] display.
13. If the called station is the pilot of a UCD [U-1] group and activates CALL FORWARDING - BUSY LINE
- D
term, the calling station will queue to the UCD [U-1] group and will not CALL FORWARD.
14. If a calling station, ATTENDANT CONSOLE [A-3], or trunk receives busy tone after setting CALL
FORWARDING - BUSY LINE [C-2] and activates EXECUTIVE RIGHT-OF-WAY [E-1], CALL
WAITING - ORIGINATING [C-31], CALL WAITING - TERMINATING [C-12], or BUSY
VERIFICATION [B-3], these services will be activated to the calling station.
15. If all the stations in the terminating Station Hunt Group are busy, the forwarding call will hear busy tone
and will not return to the calling partys Hunting Group.
16. When MULTIPLE CALL FORWARDING - BUSY LINE [M-24] service is activated, hunting will be
performed at the last destination of the forwarded call, even though the multiple jumped stations are in a
Hunt Group.
17. When the pilot station of a Hunt Group activates CALL FORWARDING - BUSY LINE - D
term to a station
(not a member of a Hunt Group) and system parameters specify that Call Hunting will be activated at the
forwarded station, the NEAX2400 IMX will send busy tone if the forwarded station is busy. If the system
parameters specify hunting at the forwarding station and the forwarded station is busy, the call will hunt
in the forwarding stations Hunt Group.CF BUSY XXXX
XXXX
                     (Time Display)  
						

							NEAX2400 IMX Business Features and Specifications
Page 84NDA-24221, Issue 3
C-2D Call Forwarding - Busy Line - Dterm
Service Conditions (cont’d)
18. When a station sets CALL FORWARDING - ALL CALLS [C-5] to a pilot in a Hunt Group, and the pilot
activates CALL FORWARDING - BUSY LINE to another station, if the system parameters define the call
to hunt to the forwarded-to Station Hunt Group and all stations are busy, the calling party will hunt at the
called stations Hunt Group. If system parameters assign the call to hunt to the forwarding Station Hunt
Group and all stations are busy, the calling party will then hunt to the forwarding stations Hunt Group.
19. This service feature can be restricted according to the service restriction class of the D
term MY Line. Even
after the CALL FORWARDING - BUSY LINE [C-2] has been set to a Dterm multi-line, incoming calls
to the multi-line cannot be transferred if the service restriction class of the MY Line restricts this service
feature.
20. A user may set CALL FORWARDING - BUSY LINE - D
term for a multi-line appearance based on the
CLASS OF SERVICE - INDIVIDUAL [C-15], as assigned to the station setting the service. The figure
below is a simplified key sheet assignment for stations 200 & 201. The CLASS OF SERVICE -
INDIVIDUAL [C-15] for station 200 is allowed CALL FORWARDING - BUSY LINE - D
term, but the
CLASS OF SERVICE - INDIVIDUAL [C-15] for station 201 is not. Station 200 is able to set CALL
FORWARDING - BUSY LINE - D
term for station 201. The associated feature button LED on station 201
will illuminate.
Note:The FORWARD-BY key is same as the CALL FORWARDING - BUSY LINE feature key.
Even when a sub-line of Dterm is assigned as the destination station, the call is not forwarded if the MY
Line of that Dterm is not allowed CALL FORWARDING - DONT ANSWER - Dterm.
21. This feature is applicable to CALL FORWARDING - OUTSIDE [C-28] and CALL FORWARDING/
MULTIPLE CALL FORWARDING - BUSY LINE - CCIS [C-46] [M-41].
22. When a user places a call to a busy station which has been set CALL FORWARDING-BUSY LINE [C-
2], the calling party can override the call forwarding feature, activating service features associated with
busy status such as CALL BACK [C-1], EXECUTIVE RIGHT-OF-WAY [E-1], STEP CALLS [S-13],
provided that the service feature class (SFC) of the calling party permits this feature. Otherwise, the call
is forwarded to a predetermined destination as usual. 
23. This service is not available when the called party is the attendant console or monitoring station. However,
the service is available when these stations are designated as the transfer destination of CALL
FORWARDING - BUSY LINE service.
24. This service is available only when the called party is busy and has set CALL FORWARDING - BUSY
LINE. In case CALL FORWARDING - BUSY LINE is set as the second hop and after in the Multiple
Call Forwarding link, this service is not available.
25. This service is available in the following occasions:
a.) When the destination of the CALL FORWARDING - BUSY LINE service is the calling station.
MY LINE MULTI-LINE MY LINE MULTI-LINE Station 200 Station 201
FORWARD-BY FORWARD-BY 
						

							NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 85
Call Forwarding - Busy Line - DtermC-2D
Service Conditions (cont’d)
b.) When the calling party is the attendant console or the night station, and the destination of the
CALL FORWARDING - BUSY LINE service is also the attendant console or the night station.
26. SPLIT CALL FORWARDING [S-99] is available only when the calling party is the station or the CCIS
line.
27. The OAI monitor number and the ACD pilot number cannot be assigned as the Call Forwarding target
telephone number except when called from a station or Tie Line trunk.
28. Telephone number must be set to the call forwarding destination.
29. This feature is not available for stations having a telephone number of seven digits or more.
30. A call can be forwarded to an Attendant Console in the remote node via FCCS link.
31. When a call is forwarded through FCCS link, the numbering plan of the originally called station must be
identical with that of the forwarded Attendant Console.
Interactions
1. If the same access code is used for CALL FORWARDING - BUSY LINE - Dterm and CALL
FORWARDING - DON’T ANSWER [C-3], only one key needs to be assigned in AKYD.
2. An ATTENDANT CAMP-ON [A-1] call is terminated at Station A, and Station A has CALL
FORWARDING - BUSY LINE - D
term set to Station B. If Station B is busy and part of a STATION
HUNTING [S-7, 8, 9] Group, the call will Camp-On at Station A and will not Hunt.
3. When CALL WAITING [C-12, 31], ATTENDANT CAMP-ON [A-1], and CALL BACK [C-1] is
directed toward Station A, which has call forwarding set to Station B, and Station B is busy, Station A will
receive Call Waiting Tone.
4. A non-controlling UCD station is allowed to activate CALL FORWARDING - BUSY LINE - D
term [C-
2]. When this station sets CALL FORWARDING - BUSY LINE - Dterm, only calls that are directly dialed
to this station are call forwarded.
5. The Attendant attempts BUSY VERIFICATION [B-3] to Station A. Station A has CALL
FORWARDING - BUSY LINE - D
term set to Station B. Station B is busy. BUSY VERIFICATION is
allowed at Station A. If Station A has set CALL FORWARDING - BUSY LINE - Dterm to the Attendant
Console, BUSY VERIFICATION [B-3] is allowed at Station A.
6. When CALL FORWARDING - BUSY LINE - D
term is in effect, the activating station may be used to
originate calls.
7. When a call follows call forwarding, the destination station is recorded for STATION MESSAGE
DETAIL RECORDING [S-10].
8. STATION-TO-STATION CALLING [S-11] must be provided.
TKNode ANode B
FCCS LinkStation A has been set
Call Forwarding service to
Attendant Console B
Attendant
Console B 
						

							NEAX2400 IMX Business Features and Specifications
Page 86NDA-24221, Issue 3
C-3 Call Forwarding - Don’t Answer
C-3 Call Forwarding - Don’t Answer
General Description
This feature permits a call to an unanswered station to be forwarded to a predesignated station, or to the Attendant,
when the called station doesnt answer after a predetermined time interval. If the individual Call Forwarding - Don’t
Answer timer is not assigned, the default timer assigned by system data programming is used.
Operating Procedure
To set CALL FORWARDING - DONT ANSWER from an individual station:
1. Lift the handset; receive dial tone.
2. Dial the specific CALL FORWARDING - DONT ANSWER access code; receive special dial tone.
3. Dial the desired target telephone number; receive service set tone.
To cancel CALL FORWARDING - DONT ANSWER from an individual station:
1. Lift the handset; receive dial tone.
2. Dial the specific CALL FORWARDING - DONT ANSWER cancel code; receive service set tone.
To set CALL FORWARDING - DONT ANSWER from the ATTENDANT CONSOLE [A-3]: 
1. Press an idle loop key.
2. Dial the specific CALL FORWARDING - DONT ANSWER access code; receive special dial tone.
3. Dial the TENANT [T-12] number (2/3 digits).
4. Dial the originating telephone number.
5. Dial the desired target telephone number; receive service set tone.
To cancel CALL FORWARDING - DONT ANSWER from the ATTENDANT CONSOLE [A-3]: 
1. Press an idle loop key.
2. Dial the specific CALL FORWARDING - DONT ANSWER cancel code; receive special dial tone.
3. Dial the TENANT [T-12] number (2/3 digits). 
4. Dial the originating telephone number; receive service set tone.
To assign individual Call Forwarding - Don’t Answer timer to each station:
1. Use the ADAI command:
a.) Parameter NAT139 overrides SYS-1, Index 139 of ASYD
b.) Parameter NAT140 overrides SYS-1, Index 140 of ASYD
c.) Parameter NAT141 overrides SYS-1, Index 141 of ASYD
d.) Parameter NAT247 overrides SYS-1, Index 247 of ASYD
2. Timer assigned to called party is valid.
Service Conditions
1. This feature may be set and cancelled by either the user or the Attendant.
2. When the Attendant extends a call to a station that has set CALL FORWARDING - DONT ANSWER,
the called station will ring for 10 seconds. If the call is not answered, AUTOMATIC RECALL [A-8] is
activated. This timing can be changed through the VARIABLE TIMING PARAMETERS [V-1] feature.
3. This feature is assigned by CLASS OF SERVICE - INDIVIDUAL [C-15] programming in System Data.
4. A station programmed for access to CALL FORWARDING - DONT ANSWER is automatically allowed
CALL FORWARDING - BUSY LINE [C-2, 2D].
5. There is no limitation to the number of stations that can set the CALL FORWARDING - DONT
ANSWER simultaneously. 
						

							NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 87
Call Forwarding - Don’t Answer C-3
Service Conditions (cont’d)
6. CALL FORWARDING - DONT ANSWER can be provided on either a tenant or an individual basis.
7. Individual CALL FORWARDING - DONT ANSWER takes precedence over tenant basis Call
Forwarding.
8. Call Forwarding on a tenant basis allows direct incoming trunk calls that encounter a Dont Answer
condition to be forwarded to a predetermined station or the ATTENDANT CONSOLE [A-3].
9. The operator answering a Call Forwarding call can identify the called telephone number on the
ATTENDANT CONSOLE [A-3] display.
10. CALL FORWARDING - DONT ANSWER from the Attendant is only activated after pressing the
RELEASE key.
11. If the stations own telephone number is set for CALL FORWARDING - DONT ANSWER, then this
feature is changed to CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING - DONT
ANSWER [C-103]).
12. When the called station does not answer for a predetermined time interval, stations are assigned this
feature according to the TENANT SERVICE [T-12] class of the calling and destination stations. In the
following cases, when the calling station and destination station are restricted by TENANT SERVICE [T-
12] class, this feature is not activated, and the called station continues to ring: 
a.) when the station called is setting CALL FORWARDING - DONT ANSWER,
b.) when a station holding an original call (station or trunk) on CONSULTATION HOLD [C-17]
places a call to a station setting CALL FORWARDING - DONT ANSWER.
13. Call Transfer - Attendant (Trunk): Trunk calls transferred by the Attendant are assigned this feature when
the called station does not answer for a predetermined time interval according to Route Restriction Class
of the trunk and the destination stations. When restricted by Route Restriction Class, this feature is not
activated, and the called station continues to ring.
14. Call Transfer - Attendant (Station): Station calls transferred by the Attendant are assigned this feature
when the called station does not answer for a predetermined time interval according to TENANT
SERVICE [T-12] class of the originating and destination stations. When restricted by Tenant Service
class, this feature is not activated, and the called station continues to ring.
15. Speed Calling List numbers may be programmed as the destination telephone number. This permits the
sent digits to exceed the 12-digit maximum.
16. CALL FORWARDING - DONT ANSWER data remains in the data memory, even if the system or LP is
reinitialized.
17. SPLIT CALL FORWARDING [S-99]: When a call is forwarded to the parties predesignated by SPLIT
CALL FORWARDING [S-99], service conditions are the same as described in items 12, 13, and 14.
18. When a call is transferred from the Attendant to a station that has set CALL FORWARDING - DONT
ANSWER, this feature may be restricted or activated according to System Data (Sys 2, Index 6, Bit 7).
19. A call can be forwarded to an Attendant Console in the remote node via FCCS link.
TKNode ANode B
FCCS LinkStation A has been set
Call Forwarding service to
Attendant Console B
Attendant
Console B 
						

							NEAX2400 IMX Business Features and Specifications
Page 88NDA-24221, Issue 3
C-3 Call Forwarding - Don’t Answer
Service Conditions (cont’d)
20. When a call is forwarded through FCCS link, the numbering plan of the originally called station must be
identical with the one of the forwarded Attendant Console.
21. If individual Call Forwarding - Don’t Answer timer is not given, the default timer assigned by ASYD
command is used.
Interactions
1. If access codes for CALL FORWARDING-BUSY LINE and CALL FORWARDING-DON’T ANSWER
are the same, only one key needs to be assigned in AKYD.
2. ACFO is applicable to DID, DIT, and TIE Line calls only.
3. A non-controlling UCD station is allowed to activate CALL FORWARDING-DON’T ANSWER. When
this station sets call forwarding, calls directed to this station will be call forwarded. The member station
is not removed from the UCD group under the conditions of the call forwarding feature used. When it is
the station’s turn to ring, that call is affected by CALL FORWARDING-DON’T ANSWER.
4. CALL FORWARDING-DON’T ANSWER to an Attendant Console will not operate when the system is
in Night mode. If ATTENDANT NIGHT TRANSFER [A-19] is provided, the call is forwarded to the
ATTENDANT NIGHT TRANSFER [A-19] station.
5. If the CALL FORWARDING-DON’T ANSWER target station is a D
term that has activated DO NOT
DISTURB [D-21D], call forwarding is not activated.
6. The CALL FORWARDING-DON’T ANSWER feature is set from Station A to Station B if Station A is
idle and Station B is busy.
7. When a call is Call Forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
8. STATION-TO-STATION CALLING [S-11] must first be provided. 
						

							NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 89
Call Forwarding - Don’t Answer - DtermC-3D
C-3D  Call Forwarding - Don’t Answer - Dterm
General Description
This feature permits a call to an unanswered station to be forwarded to a predesignated station or to the Attendant,
if the called station does not answer within a predetermined period of time. CALL FORWARDING - DONT
ANSWER - D
term may be set or cancelled by the user for all multi-line appearances on the Dterm. Additionally, a
single station user may set CALL FORWARDING - DONT ANSWER - Dterm to all sub-lines on the Dterm.
Operating Procedure
To set CALL FORWARDING - DONT ANSWER Dterm from MY Line:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Press the CALL FORWARDING - DONT ANSWER FORWARD-NA key; receive special dial tone.
3. Dial the desired target telephone number; receive service set tone. The LCD displays:
Target Station
To monitor CALL FORWARDING - DONT ANSWER from a Dterm from MY Line:
1. Press the CALL FORWARDING - DONT ANSWER FORWARD-NA key. The LCD displays:
OR
To set CALL FORWARDING - DONT ANSWER for a multi-line appearance other than the MY Line:
1. Lift the handset or press the SPEAKER key.
2. Press the multi-line appearance; receive dial tone. Press the CALL FORWARDING - DONT ANSWERFORWARD-NA key; receive special dial tone.
3. Dial the desired target telephone number; receive service set tone. The LED of the associated feature button does not light at the station s etting the service. If the multi-line app earance is another D
terms MY
Line, that stations feature key LED will light. The s etting stations LCD displays:
Target Station:
4. Replace the handset or press the SPEAKER key. 
5 .  If t h e t a rg et  s ta ti on is  t h e A tt e nd an t,  t h e  LC D  d is p la y s:
FORWARD SET
XXXX
                   (Time Display) 
FORWARD  
                                   
XXXX     
          (Time Display)        
FWD SET 
                   (Time Display) 
FORWARD SET
XXXX
                    (Time Display) 
FWD SET OPR
                    (Time Display)  
						

							NEAX2400 IMX Business Features and Specifications
Page 90NDA-24221, Issue 3
C-3D Call Forwarding - Don’t Answer - Dterm
Operating Procedure (cont’d)
To monitor CALL FORWARDING - DONT ANSWER for a multi-line appearance other than the MY Line:
1. Press the CALL FORWARDING - DONT ANSWER FORWARD-NA key. The LCD displays:
Target Station 
To cancel CALL FORWARDING - DONT ANSWER from MY Line:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Press the CALL FORWARDING - DONT ANSWER FORWARD-NA key. The associated LED goes
out. Receive service set tone. The LCD displays:
To cancel CALL FORWARDING - DONT ANSWER for a multi-line appearance other than the MY Line:
1. Lift the handset or press the SPEAKER key.
2. Press the multi-line appearance; receive dial tone. Press the CALL FORWARDING - DONT ANSWER
FORWARD-NA key; receive service set tone. The LCD displays:
The associated LED that is lit at another station goes out.
3. Replace the handset or press the SPEAKER key.
Service Conditions
1. This feature may be set and cancelled by the Dterm user or the Attendant.
2. AUTOMATIC RECALL [A-8] supersedes the timing for CALL FORWARDING - DON’T ANSWER -
D
term. Therefore, if the programmed timing for AUTOMATIC RECALL [A-8] is shorter than the
programmed timing for CALL FORWARDING - DONT ANSWER - Dterm, CALL FORWARDING -
DONT ANSWER - Dterm is disabled.
3. Stations are assigned this feature according to CLASS OF SERVICE - INDIVIDUAL [C-15]
programming in System Data.
4. A station programmed for access to CALL FORWARDING - DONT ANSWER - D
term is automatically
allowed CALL FORWARDING - BUSY LINE [C-2].
5. All stations may simultaneously activate CALL FORWARDING - DONT ANSWER - D
term.
6. If separate access codes are programmed into System Data for CALL FORWARDING - DONT
ANSWER - D
term and CALL FORWARDING - BUSY LINE [C-2], each feature must be programmed
on a separate feature button at the Dterm.
7. CALL FORWARDING - DONT ANSWER - D
term may also be accessed via the dial pad or SPEED
CALLING - ONE TOUCH - Dterm [S-26D]. If this feature is accessed via the dial pad, it must be cancelled
via the dial pad.
8. CALL FORWARDING - DONT ANSWER - D
term is not applicable to CONSULTATION HOLD - ALL
CALLS [C-17], and CALL TRANSFER - ALL CALLS [C-11].FORWARD
XXXX
                    (Time Display) 
FORWARD CANCEL
                   (Time Display) 
FORWARD CANCEL
                   (Time Display)