Toshiba Estudio 170f Manual

							19
Fit the tabs of the Document
Support into the slots on the
top side of the unit.
• Do not place heavy objects
on the Document Support or
apply strong force.
NOTE:
It may be necessary to gen-
tly bow the base of the sup-
port toward you as you
place the support into posi-
tion.Document SupportDocument Support
Installation
Hold the Front Cover by the
grips on both sides of its upper
part and pull it down to open it.
NOTE:
Do not pull the Front Cover
too strongly when opening
it.Open the Front Cover
Fit the tabs of the Recording
Paper Exit Tray onto the posts
on the back side of the unit.
• Do not place heavy objects
on the Recording Paper Exit
Tray or apply strong force.Recording Paper Exit TrayRecording Paper Exit
Tray Installation
Document Exit Tray
Fit the tabs of the Document
Exit Tray into the slots on the
front side of the unit.
• Do not place heavy objects
on the Document Exit Tray
or apply strong force.
• Extend the Document Exit
Tray Extension for long
documents.Document Exit Tray
Installation
Press up the Front Cover until
it clicks to attach securely.Close the Front Cover 
						

							20
Bypass TrayPlace the Bypass Tray on the
Recording Paper Tray.
• Do not place heavy objects
on the Bypass Tray or apply
strong force. Place the hooks of the Record-
ing Paper Tray into the guides
on the front side of the unit and
press into position.
• Do not place heavy objects
on the Recording Paper
Tray or apply strong force.
Recording Paper Tray
Installation
Bypass Tray Installation
Recording Paper Tray 
						

							21
Remove the Bypass Tray from
Recording Paper Tray.Pull down the front plate of the
Recording Paper Tray, and
then fully extend the Paper
Guide with the hook on the
right. About Recording Paper:
• Use only recommended pa-
per brands to optimize your
facsimile performance. Con-
tact your authorized TOSHI-
BA dealer for more informa-
tion.
• Remove the recording paper
when storing or relocating
your facsimile.
• Avoid using damaged,
folded or misaligned record-
ing paper. Use of damaged
paper could cause double
feeding or paper jamming.
• Use of damp recording pa-
per will cause poor printing
over all or part of the image
area. If the paper is exces-
sively moist, print quality
may become uneven and
voiding may occur.  Re-
place the paper, should this
condition exist.
• Do not add paper on top of
the paper already in the ma-
chine. If you wish to add
paper, first remove the ex-
isting paper. Then stack the
existing paper with the new
paper before inserting into
the machine.
- INITIAL PRINTING SUPPLIES INSTALLATION
Open the Paper
Guides
2
Remove the Bypass
Tray
1
Recording Paper Installation (Recording Paper Tray)
About Paper Sizes:
• Your TOSHIBA facsimile
has been preset to accept
letter size recording paper.
In the event that you re-
ceive a legal-size (8.5”x14”)
reception, it will automati-
cally be reduced to fit onto
letter-size (8.5”x11”) paper.
•If you receive only legal-
size receptions and do
not wish them to be auto-
matically reduced: Load
the legal-size paper in the
tray.
•If you receive a mixture of
letter and legal-size recep-
tions, and you do not
wish your legal recep-
tions to be automatically
reduced:
Add an optional recording
paper tray to support both
letter and legal-size paper.
With the second recording
paper tray, your TOSHIBA
facsimile will automatically
select the appropriate paper
size to match the pages
you receive.Prepare new recording paper
sheets by holding both ends
and flexing several times.
This will separate the sheets
and provide optimum feeding.
Align the stack so that all four
corners are neatly aligned.
Be sure to load the recording
paper in accordance with any
paper manufacturer’s printing
side instruction. Some papers
have a preferred image side.
This image side should be
placed face up in the Record-
ing Paper Tray.
Prepare Recording
Paper Sheets
3 
						

							22Place the recording paper
stack into the tray.
NOTES:
• Do not exceed the upper
stack limit line as this may
cause paper mis-feeds.
• Do not add paper on top of
the paper already in the ma-
chine.Adjust the Paper Guides to fit
the size of the Recording Pa-
per.
Push up the front plate of the
Recording Paper Tray to close
it.
Install the
Recording Paper
4
Replace the Bypass Tray.
CAUTION:
Do not place heavy objects
on the Document Exit Tray
or apply strong force.
Press:
MENU++++
The menu below displays:
Display the Paper
Size Menu
7
Recording Paper Installation (Recording Paper Tray) - continued
NOTE:
If you install legal size pa-
per but fail to select “3.LG”
at this point, the machine
will think letter size paper is
installed. False “Paper Jam”
failures will occur when the
legal size paper is fed into
the printer.
Adjust the Paper
Guides
5
Replace the Bypass
Tray
6
Select the Paper
Size
8Select the paper size of the
Recording Paper Tray.
To select letter size, press:To select A4 size, press:To select legal size, press:
Displayed for 2 seconds
Returns to display the SETUP
menu screen.
3.LG2.A4PAPER SIZE (TRAY 1)
1.LT
COMPLETED 
						

							23
Return to the
Standby Mode
9Press 
STOP
 to return to the
Standby Mode.
Recording Paper Installation (Recording Paper Tray) - continued 
						

							24Open the Paper Guides.
Open the Paper
Guides
1Recording Paper Installation (Bypass Tray)
Insert a one sheet of paper on
the Bypass Tray.
CAUTION:
Do not insert more than one
sheet of paper on the By-
pass Tray.
It will cause a paper jam.
Adjust the Paper
Guides
3
Insert the Recording
Paper
2
Adjust the Paper Guides so
that both sides of the paper are
secure.
NOTE:
The single sheet of paper in the Bypass Tray will be fed in-
stead of the paper in the Recording Paper Tray. If the machine
is equipped with the optional Lower Paper Tray, the single
sheet in the Bypass Tray will feed only when the Upper Paper
Tray is selected. 
						

							25
Remove the Optional Record-
ing Paper Tray.Remove the Optional Tray
Cover.
Remove the
Optional Tray Cover
2
Prepare new recording paper
sheets by holding both ends
and flexing several times.
This will separate the sheets
and provide optimum feeding.
Align the stack so that all four
corners are neatly aligned.
Be sure to load the recording
paper in accordance with any
paper manufacturer’s printing
side instruction. Some papers
have a preferred image side.
This image side should be
placed face up in the Recording
Paper Tray.
NOTE:
There are two types of the
Optional Recording Paper
Tray, one for A4-size paper
and another for letter-size
paper. Use the Tray meet-
ing your paper size.
Prepare Recording
Paper Sheets
4
Press the Paper Pressure Plate
down until it clicks.
Place the recording paper
stack into the tray.
NOTES:
• Do not exceed the upper
stack limit line as this may
cause paper misfeeds.
• Make sure that the paper is
seated under the two sepa-
ration claws on the back
side of tray.
• Be careful not to damage
the claws of the Recording
Paper Tray.
• Do not add paper on top of
the paper already in the ma-
chine.
Press Down the
Paper Pressure Plate
3
Install the Recording
Paper
5
Remove the Optional
Recording Paper
Tray
1Recording Paper Installation (Optional Recording Paper Tray) 
						

							26Replace the Optional Paper
Tray Cover.Insert the Optional Recording
Paper Tray all the way into the
machine.
NOTE:
As the tray is inserted, lis-
ten for the sound of the pa-
per pressure plate moving
up into position.
Recording Paper Installation (Optional Recording Paper Tray) - continuedReplace the Optional
Tray Cover
6
Insert the Optional
Recording Paper Tray
7
Press:
MENU++++
The menu below displays:
Display the Paper
Size Menu
8
Select the paper size of the
Recording Paper Tray.
To select letter size, press:To select A4 size, press:To select legal size, press:
Displayed for 2 seconds
Returns to display the SETUP
menu screen.
Select the Paper Size
of the Recording
Paper Tray
9
Select the paper size of the
Optional Recording Paper Tray.
To select the letter size, press:To select the A4 size, press:
Select the Paper Size
of the Optional
Recording Paper Tray
10
3.LG2.A4PAPER SIZE (TRAY 1)
1.LT
2.A4PAPER SIZE (TRAY 2)
1.LT
COMPLETED 
						

							27
Return to the
Standby Mode
11Press 
STOP
 to return to the
Standby Mode.
Recording Paper Installation (Optional Recording Paper Tray) - continued 
						

							28
Hold the Front Cover by the
grips on both sides of its upper
part and pull it down to open it.
NOTE:
Do not pull the Front Cover
too strongly when opening
it.NOTE:
Do not touch the Develop-
ment Roller of the Toner
Cartridge. The image quality
could be degraded.
Open the Front
Cover
1
Drum Unit and Toner Cartridge Installation
Mix the Toner by shaking the
Toner Cartridge back and forth.
NOTE:
Avoid touching the toner to
your clothing since toner
cannot be removed easily.
If the toner sticks to your
clothing, immediately rinse
out the toner with cold wa-
ter.
Prepare a Toner
Cartridge
2
Match the colored parts in the
lower area of the Drum Unit
with the same colored parts in
the lower area of the Toner Car-
tridge.
NOTES:
• Keep the Toner Cartridge
level with the Drum Unit
when they are detached.
• Do not touch the PC Drum
under the lid of the Drum
Unit. The image quality
could be degraded.
• Do not touch the metal area
of the Toner Cartridge. It
could be damaged due to
electrostatic interference.
Attach the Toner
Cartridge to the
Drum Unit
4
IMPORTANT:
When you use a toner cartridge
of our recommendation, the
facsimile machine can detect
whether or not the cartridge is
inserted in the machine and
alert the  user when the amount
of toner is low or needs replac-
ing. As the facsimile machine
does not start printing when the
toner is not inserted or when
the amount of toner is insuffi-
cient, loss of received data can
be prevented. If a toner car-
tridge other than that of our rec-
ommendation is used, the ma-
chine may not be able to detect
whether the toner cartridge has
been inserted or if the toner
amount is sufficient, and print-
ing is not possible using the
default setting.
If you want to use a toner car-
tridge other than that of our rec-
ommendation, please inform
our service center. The service
center will change the machine
setting to cancel the detection
function. Please note, however,
that when the setting is so
changed, the machine will start
printing even if a toner cartridge
is not inserted or the toner
amount is insufficient. Conse-
quently, the printout may not
be satisfactory and the re-
ceived data may be lost.
Remove the protective
cover from the Toner
Cartridge
3