Toshiba Estudio 170f Manual

							229
LCD TEST
Select the LCD TEST
Menu
1Press:
+
+
+
+ The LCD test checks LCD op-
eration by turning on and off all
the elements of the LCD on the
Operation Panel.
Start the LCD Test
2Press:
Select the Test Result
Option
3If all elements of the LCD turn
on and off normally, press:
Completed the
LCD TEST
4The word “OPERATION COM-
PLETED” is displayed on the
screen and the unit returns to
the individual test selection
screen.
The result of the LCD test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST RESULT” on page 235.
If the result of the LCD test is
judged to be NG, call your ser-
vice representative.
LCD TEST
PRESS [START]
MENU
An underline moves from the
first column through the last
column of the LCD, and then all
elements turn on as shown.
START
If even one element fails to
turn on and off, press:
2.NGLCD TEST
1.OK ADisplayed for 5 seconds 
						

							230SPEAKER TEST
Select the SPEAKER
TEST Menu
1Press:
+
+
+
+ The speaker test checks
speaker operation by changing
the volume output from the
speaker.
Check the Speaker
Volume
2
Select the Test Result
Option
3If all volumes are output nor-
mally, press:
Completed the
SPEAKER TEST
4The word “OPERATION COM-
PLETED” is displayed on the
screen and the unit returns to
the individual test selection
screen.
The result of the speaker test
can be confirmed with the self
test report. To print the self
test report, refer to “PRINTING
A TEST RESULT” on page
235.
If the result of the speaker test
is judged to be NG, call your
service representative.
SPEAKER TEST
PRESS [START]
After checking, press:>
>>
>>>
>>>>
>>>>>
>>>>>>
OFF
MENU
Pressing 
START
 changes the
volume level from “>” (mini-
mum) to “>>>>>>” (maximum)
and “OFF” (no sound).
STOP
If even one of them is not out-
put normally, press:
2.NGSPEAKER TEST
1.OK 
						

							231
SENSOR TEST
Select the SENSOR
TEST Menu
1Press:
+
+
+
+ The sensor test checks if the
detection sensors operate nor-
mally.
The test items in SENSOR
TEST mode are as follows:
• Detection of Top Cover
open/closed status
• Detection of Front Cover
open/closed status
• Detection of Recording Pa-
per and Recording Paper
Tray presence/absence sta-
tus
NOTE:
When the sensor has bro-
ken, display does not
change next.
But about 40 seconds
passed, it will be set to NG.
Check the Top Cover
2Open the Top Cover. When its
open state is detected, the
screen below appears. After
checking that the screen is dis-
played, close the Top Cover.
Detects  the open state
of the Top Cover.
SENSOR TEST
OPEN TOP COVER
Close the Top
Cover
SENSOR TEST
OPEN FRONT COVERSENSOR TEST
CLOSE TOP COVER
MENU
If no recording paper is placed
in the Recording Paper Tray,
the screen below is displayed.
You can resume the test by
loading the paper.
SENSOR TEST
PUT IN PAPERCheck the Front
Cover
3Open the Front Cover. When
its open state is detected, the
screen below appears. After
checking that the screen is dis-
played, close the Front Cover.
Detects  the open state
of the Front Cover.
Close the Front
Cover
SENSOR TEST
REMOVE PAPERSENSOR TEST
CLOSE FRONT COVER 
						

							232SENSOR TEST - continued
Completed the
SENSOR TEST
5The result of the sensor test
can be confirmed with the self
test report. To print the self
test report, refer to “PRINTING
A TEST RESULT” on page
235.
If the result of the sensor test
is judged to be NG, call your
service representative.
Remove the Recording Paper
in the Recording Paper Tray.
When the absence of a Paper
is detected, the screen below
appears. After checking that
the screen is displayed, install
the Recording Paper in the Pa-
per Tray.
Detects  the absence of
the Recording Paper.If an Optional Recording Paper
Tray is installed, follow the
same test procedure for the
Optional Recording Paper Tray.
Install the Recording
Paper
SENSOR TEST
OKSENSOR TEST
PUT IN PAPER
Detects the absence
of the Recording Paper
SENSOR TEST
PUT IN PAPER TRAY 2SENSOR TEST
REMOVE PAPER TRAY 2Install the Recording Paper
The result of the sensor test
(“OK” or “NG”) is displayed on
the screen, and the unit returns
to the individual test selection
screen.
Check the Paper Tray
4 
						

							233
PRINT TEST
Select the TEST
PRINT Menu
1
The print test checks the print function by printing a test pattern.
The test pattern is printed.
PRINT TEST
PRINTING LIST
Completed the
PRINT TEST
3The word “OPERATION COM-
PLETED” is displayed on the
screen and the unit returns to
the individual test selection
screen.
The result of the print test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST RESULT” on page 235.
If the result of the print test is
judged to be NG, call your ser-
vice representative.
Select the Print
Result Option
2If the test pattern prints prop-
erly, press:
Print Sample
Press:
+
+
+
+
MENU
If the test pattern did not print
properly, press:
2.ONPRINT TEST
1.YES 
						

							234TONER IC TEST
Select the TONER IC
TEST
1Press:
+
+
+
+ Toner IC Test checks if the IC
chip attached to the toner car-
tridge can be read correctly or
not.
Display the Test
Result
2
Completed the
TONER IC TEST
3The result of the toner IC test
can be confirmed with the self
test report. To print the self
test report, refer to “PRINTING
A TEST RESULT” on page
235.
If the result of the toner IC test
is judged to be NG, call your
service representative.
TONER IC TEST
TESTING
If the test result is OK.
MENU
Start the Toner IC Test
TONER IC TEST
OK
If the test result is NG.
TONER IC TEST
NG
Press: 
						

							235
This test result list prints out the results of the individual tests as
a self test report.
PRINTING a TEST RESULT
Select the TEST
RESULT Menu
1Press:
+
+
Print Sample
 - TEST RESULT
After completion of the list out-
put, the display returns to the
standby mode screen.
MENU 
						

							236Automatic Supplies Order Setting- REMOTE SERVICE-AUTOMATIC SUPPLIES ORDERThis machine can automatically send an order sheet to a designated fax m\
achine informing your supplier that a replacement Drum Unit or Toner Cartridge is required.
Contact your local authorized dealer for information on this setting. 
						

							237
Document Size:Width..... 216 mm (8.5 inches) max.
148 mm (5.83 inches) min.
Length ... 1000 mm (39.37 inches) max.
100 mm (3.94 inches) min.
Recording Paper Size:Letter, Legal, A4
Recording Paper Tray Capacity:Up to 250 sheets
(with the recommended paper)
Bypass Tray Capacity:1 sheet (with the recommended paper)
Effective Scanning Width:214 mm (8.43 inches)
Effective Printing Width:208 mm (8.2 inches)
Compatibility Communication Modes:
ECM, G3
Scanning Density:Horizontal..... 8 dots/mm (203 dpi),
16 dots/mm (406 dpi)
Vertical ......... 3.85 lines/mm (98 lines/inch)
7.7 lines/mm (196 lines/inch)
15.4 lines/mm (392 lines/inch)
Transmission Rate:V17 and V.34:
33600/31200/28800/26400/24000/21600/19200/
16800/14400/12000/9600/7200/4800/2400 bps
Encoding Systems:JBIG/MMR/MR/MH
Recording and Printing Method: Electrophotography and Laser Printing
Memory Capacity:7 MB
Machine Type:Desktop type with both transmission and re-
ception functions
Applicable Networks:PSTN (Public Switched Telephone Network)Power Required:110 VAC, 50/60 Hz
Power Consumed:Max. 1000 W (operating), 2 W or less (standby
in Super Energy Saver mode)
Unit Dimensions:Width..... 408 mm (16.06 inches)
Depth ..... 685 mm (26.97 inches)
Height .... 403 mm (15.87 inches)
(All dimensions excluding protrusions)
Weight:Less than 11.5 kg (25.35 lbs.)
Outer appearance, specifications, etc. may be changed without prior notice.If any trouble is encountered, contact your authorized TOSHIBA facsimile
dealer.The clock function and programming data of this device are preserved with a
built-in battery. If the power supply is cut off over a long time, the battery may
become discharged, causing the recorded data to be lost.
SPECIFICATIONS 
						

							238Letter-size Recording Paper:
Legal-size Recording Paper:
Drum Unit:OD170F
Toner Cartridge:T170FOptional Paper Tray:MY-1025LT
Handset:GJ-1110SUPPLIES
HARDWARE OPTIONS