Toshiba Estudio 170f Manual

							219
Install the Process Unit into
the machine, aligning the
guides of the Unit with the
grooves inside the machine.
Make sure the Process Unit is
inserted inside the machine as
far as it will go.
NOTE:
Pressing in the Process
Unit forcibly could damage
the machine.
Clearing a Recording Paper Jam - continuedInstall the Process
Unit
15
Press up the Front Cover until
it clicks to ensure the latches
are engaged.
Close the Front
Cover
16
Close the RX Cover
17Press down on the RX Cover
until a “Click” is heard to en-
sure the latches engage.
Verify the display has returned
to the Standby Mode.
If there is any received
document stored in
memory ...
If a recording paper jam oc-
curs during a reception, the
received documents are au-
tomatically stored in memo-
ry. In that case, the facsimi-
le will automatically print out
the received contents stored
in memory after clearing the
paper jam (if power was not
turned off). 
						

							220If the Document Scanner Unit
is dirty, your documents may
not be transmitted clearly. If
the Recording Unit is dirty, the
document you receive may not
be clear.  In that case, clean
the Document Scanner Unit or
Recording Unit using the fol-
lowing procedures. You can
check these problems by mak-
ing a copy.
Examples of print problem:
Open the Operation Panel. Wipe the Glass surface and
the White Plate with a soft dry
cloth.
• If it is very dirty, wipe it with
a cloth soaked in water and
wrung out, then wipe it with
a dry cloth.
When the Recorded Image is not Clear...
Open the Operation
Panel
1
Wipe the Glass
Surface and White
Plate
2
Document Scanner Cleaning Procedure
Wipe the ADF Pad and Rollers
with a dry cloth.
• If it is very dirty, wipe it with
a cloth soaked in water and
wrung out, then wipe it with
a dry cloth.
CAUTION:
Be careful not to injure your
finger(s) on the ADF spring
when you wipe the ADF
pad.
Wipe the ADF Pad
and Rollers
3
If the problem occurs during
both a transmission and in
copy mode, check the Docu-
ment Scanner Unit.
If the problem occurs during
both receptions and copy
mode, check the Recording
Unit. 
						

							221
Close the Operation Panel.
• Make sure that the hooks
on both sides are firmly
latched.
Close the Operation
Panel
4When the Recorded Image is not Clear...  - continuedDocument Scanner Cleaning Procedure  - continued 
						

							222
Open the Front
Cover
1Hold the Front Cover by the
grips on both sides of its upper
part and pull it down to open it.
NOTES:
• If a problem with the Re-
cording Unit remains after
this action, you may re-
quire a new Toner Car-
tridge or Drum Unit.
Check for dirt or paper un-
der the Toner Cartridge
and Drum Unit first. Call
your service representa-
tive for assistance.
• Do not pull the Front Cover
too strongly when opening
it.
Recording Unit Cleaning ProcedureWhen the Recorded Image is not Clear...  - continued
Wipe the Paper
Pickup Roller, etc.
3Wipe the Paper Pickup Roller
with a dry cloth. If the surfaces
require moisture to remove the
dirt, use a cloth slightly damp-
ened with water to remove the
dirt, followed by a dry cloth.
Lift up and holding the green
handle, gently pull out the Pro-
cess Unit.
CAUTION:
Always hold the Process
Unit by the green handle.
Remove the Process
Unit
2
Process Unit
4Install the Process Unit into
the machine, aligning the
guides of the Unit with the
grooves inside the machine.
Make sure the Process Unit is
inserted inside the machine as
far as it will go.
NOTE:
Pressing in the Process
Unit forcibly could damage
the machine.
Press up the Front Cover until
it clicks to attach securely.
Verify the display has returned
to the Standby Mode.
Close the Front
Cover
5 
						

							223
USER TEST MODE - AUTOMATIC TEST MODEAUTO TEST
Display the TEST
MODE Menu
1
AUTO TEST mode permits you to automatically perform a series
of machine tests in one operation.
The test items performed by the AUTO TEST are:
•FLASH ROM TEST
Checks the program data, function data, and language data.
•SRAM TEST
Checks the SRAM Memory.
•DRAM TEST
Checks the DRAM Memory.
•MODEM TEST
Checks the modem and checks for phone line current.
•SCANNER TEST
Checks the image scanner.
•CODEC TEST
Checks the CODEC IC.
•PRINTER TEST
Checks the printer components for proper operation and prints
one test page.
•TONER IC TEST
Checks the TONER IC.
NOTES : •AUTO TEST cannot be performed if data (such as re-
ceived data, delayed transmission, or polling data) is
stored in memory.
•AUTO TEST takes approximately 7.5 minutes to com-
plete.Press:
+
Select the AUTO
TEST Menu
2Press:
Completed the
AUTO TEST
3When all the tests end, the
word “OPERATION COM-
PLETED” is displayed on the
screen and a Test Pattern is
printed. After printing, the dis-
play returns to showing the
standby mode screen.
The results of the auto test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST RESULT” on page 235.
If the result of the auto test is
judged to be NG, call your ser-
vice representative.
MENU
To suspend the auto test,
press 
STOP
 . The auto test starts, 
 appears
on the screen indicating that
the test is under way.
3.TEST RESULT LIST2.INDIVIDUAL TESTTEST MODE
1.AUTO TEST
AUTO TEST
      ---------------AUTO TEST  ------------------- 
						

							224INDIVIDUAL TEST Summary
In INDIVIDUAL TEST mode,
you can perform specific tests
on this facsimile.
Press:
+
+
Enter the INDIVIDUAL
TEST Menu
1
Select the Desired
INDIVIDUAL TEST
(01-07)
2Press 
 or 
MENU
 un-
til the desired INDIVIDUAL
TEST is displayed or enter the
desired INDIVIDUAL TEST (01
through 08) using the dial key-
pad.
 - INDIVIDUAL TEST MODE
NOTE:
Only 1 selection can be dis-
played at one time.
MENU
INDIVIDUAL TEST
01.ADF TEST
02.KEY TEST
03.LED TEST
04.LCD TEST
05.SPEAKER TEST
06.SENSOR TEST
07.PRINT TEST
08.TONER IC TEST 
						

							225
ADF TEST
Press:
+
+
+
+
Select the ADF TEST
Menu
1
The ADF test checks the op-
eration of the ADF by trans-
porting and unloading docu-
ments. You can check that the
ADF is normal if the number of
documents loaded is consis-
tent with the number of docu-
ments transported and un-
loaded.Load the documents in the
document support.If a document jam occurs dur-
ing transport, the screen below
is displayed.
Remove the jammed docu-
ments, the screen below is dis-
played.
ADF TEST
LOAD DOCUMENT
ADF TEST
PAGES             01
ADF TEST
DOCUMENT JAM
To continue the ADF Test,
press:
ADF TEST
[STOP] TO COMPLETE
Load the Documents
2
ADF TEST
PRESS[START]
To end the test, press:
Select the ADF Test
Result
3If the number of documents
loaded is consistent with the
number of documents unload,
press:
You can change the transport
speed by pressing 
MODE
.
STD: Fast
FINE (Same when HALF
TONE is set):Medium
U-FINE (Same when HALF
TONE is set): Slow
MENU
Press:
The documents will be trans-
ported one by one and the
number of documents unloaded
will be displayed at the lower
right on the screen.
START
Go to Step 3.
STOP
Return to Step 2.
START
If a document has not fed prop-
erly (even once), press:
2.NGADF TEST
1.OK 
						

							226ADF TEST - continued
Completed the
ADF TEST
4The word “OPERATION COM-
PLETED” is displayed on the
screen and the unit returns to
the individual test selection
screen.
The result of the ADF test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST RESULT” on page 235.
If the result of the ADF test is
judged to be NG, call your ser-
vice representative. 
						

							227
KEY TEST
Select the Key Test
Menu
1Press:
+
+
+
+ The key test checks key
switch operation on the Opera-
tion Panel.
Check the Keys
2Press all the key switches ex-
cept 
STOP
.
If all the keys except 
STOP
have been detected, the screen
below is displayed.
Exit the Key Test
Mode
3
The result of the key test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST RESULT” on page 235.
If the result of the key test is
judged to be NG, call your ser-
vice representative.
Completed the
KEY TEST
4
KEY TEST
PRESS [STOP] LAST
KEY TEST
PRESS [STOP]
KEY TEST
OKKEY TEST
NG
NOTE:
If you press 
STOP
 before
you press every key, the
machine will reset to the
Individual Test menu
screen and no test result
will be issued. NOTE:
The name of each key is
displayed on the LCD after
it is pressed.
MENU
Press:
The result of the key test
(“OK” or “NG”) is displayed on
the screen, and the unit re-
turns to the individual test
menu screen.
STOP
Unless 
STOP
 is pressed
within 10 seconds after the
screen in Step 2 is displayed,
the test result is judged to be
NG. 
						

							228LED TEST
Select the LED TEST
Menu
1Press:
+
+
+
+
All the LEDs blink or light with
the following message dis-
played. The LED test checks LED op-
eration by lighting all the LEDs
on the Operation Panel.
Check the LCDs
2Visually check that all the
LEDs are on. After checking,
press 
STOP
.
Select the Test Result
Option
3
Completed the
LED TEST
4The word “OPERATION COM-
PLETED” is displayed on the
screen and the unit returns to
the individual test selection
screen.
The result of the LED test can
be confirmed with the self test
report. To print the self test re-
port, refer to “PRINTING A
TEST” on page 235.
If the result of the LED test is
judged to be NG, call your ser-
vice representative.
LED TEST
[STOP] TO COMPLETED
MENU
If there was no input for 1
minute, Returns to display the
SETUP menu screen.If all the LEDs turn on, press:
If even one LED is not lit,
press:
2.NGLED TEST
1.OK