Nortel Modular Ics 6.1 Installer Guide
Have a look at the manual Nortel Modular Ics 6.1 Installer Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 211 Nortel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Private networking using PRI SL-1 / 161 P0603534 02Modular ICS 6.1 Installer Guide Assigning PNIs 1. After you enter your password, press ‘ until the prompt displays System Prgrming: 2. Press ≠. The prompt displays Hunt groups. 3. Press ‘ until the prompt displays Dialing Plan. 4. Press ≠. The prompt displays Private Network. 5. Press ≠. The prompt displays Type. 6. Press CHANGE to until you reach CDP. 7. Press ‘. The prompt displays PrivNetID. 8. Enter the private network ID for your system. Assigning PNIs for adjacent nodes 1. After you enter your password, press ‘ until the prompt displays Hardware: 2. Press ≠. The prompt displays Show module. 3. Enter the module where the PRI card you have configured for SL-1 resides. 4. Press ≠. The prompt displays CdX-KSU. 5. Press ≠. The prompt displays Card type. 6. Press ‘. The prompt displays Lines. 7. Enter the line number you want to configure. 8. Press ≠. The prompt displays Protocol. 9. Ensure that this displays SL-1. 10. Press ‘. The prompt displays PrivNetID:. 11. Enter the PNI of the adjacent node.
162 / Private networking using PRI SL-1 Modular ICS 6.1 Installer GuideP0603534 02 12. Repeat these steps for all the modes that are directly adjacent to your system. Local system To set up the local system, you need to assign a target line to the DN for the voice mail system, then enter that DN into the target line record. 1. After you enter your password, at the Terminals&Sets prompt, press ≠. The prompt displays: Show set: 2. Enter the DN number for the Auto Attendant. 3. Press ≠. The prompt displays Line access. 4. Press ≠. The prompt displays Line assignment. 5. Enter the target line number for the Auto Attendant system. 6. Press CHANGE to change the setting for each line to one of the following: Unassigned, Ring only, Appr&Ring, and Appr only. 7. Press – until you reach the top level, then press ‘. The prompt displays Lines. 8. Press ≠. The prompt displays Show line. 9. Enter the target line number you entered in step 5. 10. Press ≠. The prompt displays Line Type. 11. Press ‘. The prompt displays Rec'd #. 12. Enter the DN for the Auto Attendant system. 13. Exit programming.
Private networking using PRI SL-1 / 163 P0603534 02Modular ICS 6.1 Installer Guide Remote system On the nodes that are not directly connected to the central Auto Attendant system, you need to use the Telco Features headings to identify the route to the system. 1. After you enter your password, press ‘ until the prompt displays Telco Features: 2. Press ≠. The prompt displays VMsg Center tel#s. 3. Press ≠. The prompt displays VMsg Center 1. 4. Press ≠. The prompt displays Use:. 5. Press CHANGE to until you reach Routing tbl. 6. Press ‘. The prompt displays Tel #:. 7. Enter the number to access the external Auto Attendant system. Set Telco features for the CAA DN 1. Press – until you reach the top level, then press ‘ until the prompt displays Terminals&Sets. 2. Press ≠. The prompt displays: Show set: 3. Enter the DN for the Auto Attendant system. 4. Press ≠. The prompt displays Line access. 5. Press ‘ until the prompt displays Telco features. 6. Press ≠. The prompt displays Feature Assign. 7. Press ≠. The prompt displays Show line. 8. Enter the line number that connects to the system for the central voice mail system.
164 / Private networking using PRI SL-1 Modular ICS 6.1 Installer GuideP0603534 02 9. Press ≠. The prompt displays Caller ID Set. 10. Press ‘ until the prompt displays Extl VMsg set. 11. Press CHANGE to select Y (yes). Set Telco features for the target line 1. Press – until you reach the top level, then press ‘ until the prompt displays Lines. 2. Press ≠. The prompt displays: Show line: 3. Enter the target line number for the voice mail system. 4. Press ≠. The prompt displays: Trunk/line data: 5. Press ‘ until the prompt displays Telco features. 6. Press ≠. The prompt displays VMsg Center 1. 7. Press ≠. The prompt displays Use:. 8. Press CHANGE to until you reach Routing tbl. 9. Press ‘. The prompt displays Tel #:. 10. Enter the number to access the external Auto Attendant system. 11. Exit programming. Voice mail configuration On the voice mail system, set the following parameters: •Set Redirected DN to Yes. • Under the F983 AA prompt, set ANS: Y for the voice mail DN assigned target line. • Under F983 dial 77 and set External init as Y.
Private networking using PRI SL-1 / 165 P0603534 02Modular ICS 6.1 Installer Guide • From the CVM/CAA lines, use the default greeting table 1. For detailed directions, refer to the addendum titled: Installing Norstar Voice Mail as a Centralized Voice Mail System.
166 / Customer Use Modular ICS 6.1 Installer GuideP0603534 02 Customer Use This section shows sample configurations for different types of network access. Each example has four parts: • A scenario explains the goal of the call and what is required to achieve it. • A diagram shows the network configuration that supports the application. • A list shows the Norstar hardware required to support the configuration. • Tables show the programming. Only those settings that are important to network access are described. Public network The calls described in this section all originate from the public network. Callers dial in using a public DN into the system. Call one or more Norstar telephones Ms. Nelson is a bank customer with a question for an accountant. She dials the number that maps onto target line 203. All of the telephones ring in the accounting department. Hardware: ICS, a Trunk Module with a DID Trunk Cartridge, or a DTI with lines programmed as DID. Trk/Line DataRecd # Line 0514321 (for Line 203) DID Recd # lengthRecd # lengthfour digits (can be from three to seven digits, but must match number of digits sent by central office)
Customer Use / 167 P0603534 02Modular ICS 6.1 Installer Guide Call Norstar and select tie lines to a private network A manager in Georgia wants to use the tie lines at headquarters to call Washington. He dials a telephone number that maps onto the DISA DN, enters a Class of Service (COS) password, then dials a line pool access code to select a tie line to Washington. Using tie lines Ta r g e t l i n e 203 Ms. Nelson DIDAccountant (225) Accountant (226) Central OfficeDID trunk cartridges Manager (in Georgia) Central Office NorstarDIDDID and E&M/DISA trunk cartridges E&M line pool to Washington
168 / Customer Use Modular ICS 6.1 Installer GuideP0603534 02 Hardware: ICS, a Trunk Module with a DID Trunk Cartridge, two E&M/DISA Trunk Cartridges for the three trunks in the line pool to Washington, or a DTI with one DID line and three E&M lines. Incoming trunk: Trk/Line Data Line 049DID Access codesDISA DN5321 Recd # lengthRecd # lengthfour digits (three to seven digits, but must match number of digits sent by central office) Outgoing trunk: Trk/Line Data Line 053 Line typeE&M Pool F Access codesLine pool F6 (up to four digits) COS pswdsDefine restrictions. Define remote access pkgs. Assign a restriction filter to the line. Assign COS passwords and filters for each Class of Service.
Customer Use / 169 P0603534 02Modular ICS 6.1 Installer Guide Call Norstar and select lines to the public network Gord wants to make a long-distance business call from home. To avoid being charged, he dials the telephone number that maps onto the Auto DN at work. After hearing the dial tone, Gord dials a line pool access code to select a line to the public network. He then dials the long-distance number. Using DID to dial long-distance Hardware: ICS, a Trunk Module with a DID Trunk Cartridge or DTI with several DID lines. Incoming trunk: Trk/Line Data Line 049DID Access codes Auto DN4321 Recd # lengthRecd # lengthfour digits (can be from three to seven digits, but must match number of digits sent by central office) Lines /Restrictions and Remote accessDefine restriction filters. Define remote access packages. Assign a remote restriction and remote package to the line. Gord at home Business client Central Office Central OfficeNorstar DID line pool
170 / Customer Use Modular ICS 6.1 Installer GuideP0603534 02 Private network All the calls described in this section originate from within the networked system. Call one or more Norstar telephones The production supervisor in Houston selects the less- expensive company Tie line to call the manager at the Administration office in Dallas. Once the line is selected, the production supervisor dials the digits that will map onto the target line of the manager in Dallas. Calling from a Norstar to a remote PBX Hardware: ICS, a Trunk Module with an E&M/DISA Trunk Cartridge or a DTI with an E&M line. Outgoing trunk: Trk/Line Data Line 001 Line type Loop Pool A Access codesLine pool A1234 Lines /RestrictionsAssign a restriction filter to the line. Incoming trunk: Trk/Line Data Recd # Line 049 Ans Mode4321 (for target line 243) E&M Auto PBX in HoustonManager in Dallas Norstar E&M target line 243