Mitel SX-200 DIGITAL Pabx Information Manual
Have a look at the manual Mitel SX-200 DIGITAL Pabx Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation Forms NOTES FOR FIGURE 4-2 E&M/TIE TRUNK CARD SWITCH FUNCTIONS Notes: 1. Trunk impedance switches are located on the rear face of the Trunk Card. 2. Outgoing/incoming switch settings: Outgoing Incoming Busy Switch Busy Switch Result Set to Set to Idle Busy Normal trunk operation - if trunk is made busy by attendant, outgoing busy, incoming busy condition results. See below. Busy Busy Trunk cannot be seized, incoming or outgoing from the ACD system. Recommended setting if trunk is not connected to trunk circuit. Busy Idle Outgoing calls receive busy tone. incoming calls receive ringing tone but cannot be answered. Idle Idle If trunk is made busy by attendant, outgoing busy, incoming idle condition results. See below. Incoming busy switch, wh.en operated, will provide an outgoing seize signal whenever the trunk is made outgoing busy (either from the outgoing busy switch on the trunk, or from the console). 3. Normal gain provides 0.5 dB insertion loss through the ACD. Special gain provides for 4-wire operation with carrier systems requiring signal levels of +7 dB on the Rx pair, and -16 dB on the TX pair. Page 4-7
Installation Forms TABLE 4-3 TRUNK CARD SWITCH SETTINGS - DID/TIE TRUNK CARD TRUNK NUMBER (l-200) SWITCH SETTINGS INCOMING CONDITIONS BUSY IDLE OUTGOING CONDITIONS ““1 1 1 SWITCH “A” SETTING CLOSED OPEN SWITCH ‘3” SETTING CLOSED OPEN SWITCH “A” SETTING ;WlTCH “B” SETTING CLOSED OPEN CLOSED OPEN JNCOMING WINK WINK INCOMING WINK WINK NO WINK OUTGOING WINK WINK NO WINK 3i SY I I I iiNK IMPEDANCE 600 OHM VITCHES (3) 900 OHM PULSING CONDITION BATTERY/GROUND LOOP DIALING CONDITIONS STOP DIAL NOT STOP DIAL SHEET _ OF _ TRUNK 1 TRUNK 2 BAV NUMBER SLOT NUMBER :IRCUIT NUMBER rRUNK NUMBER (l-200) OUTGOING CONDITIONS BUS!’ IDLE NO WINK OUTGOING WINK WINK NO WINK TRUNK IMPEDANCE 600 OHM SWITCHES (3) 900 OHM PULSING CONDITION BATTERY/GROUND LOOP DIALING CONDITIONS STOP DIAL NOT STOP DIAL NOTE: TRUNK CARD SWITCHES MUST BE SET TO ONE POSSIBLE SETTING FOR EACH SWITCH AS DETAILED IN SECTION MITL9108-093-ZOO-NA. SHIPPING, RECEIWNG AND INSTALLATION INFORMATION. FRM0128Rl Page 4-8
Installation Forms L TRUNK CONTROL SWITCHES 1 TABLE TRUNK TVPE SWITCH A SWITCH B DID TRUNK CLOSED CLOSED I ““P TIE TPIINUK CLOSED OPEN ---. ..- . ..-._.. ------ _. -.. INCOMING DIAL - 1 OPEN 1 CLOSED OUTGOlN NOT USE” , VrLI” , “TLI” , NORMAL SETTING 5 = CLOSED 6 = CLOSED 7 = CLOSED 8 = CLOSED 9 = NOT USED 10 = NOT USED ,-OPEN SEE TABLE OUTGOING WINK I # NOT OUTGOING WINK SWITCH r---1 6000 :---:9oon L---J SW3 TRUNK 1 IMPEDANCE SWITCHES 8 TRUNK BUSY SWITCHES 6OO.Q :;: SW11 I I r----l 6OOfz pe-j goof2 Li-1 9oocl SW3 pcy I I I SW21 I 1 TRUNK 2 ?IJ IMPEDANCE 9ool-l SWITCHES TRUNK BUSY SWITCHES 1 NORMAL SETTING 1 = CLOSED 2 = CLOSED 3 = CLOSED 4 = CLOSED 5 = OPEN 6 = OPEN 7 q CLOSED 8 = CLOSED 5496RlEl Figure 4-3 DID/Tie Trunk Card Switch Functions Page 4-9
Installation Forms NOTES FOR FIGURE 4-3 DID/TIE TRUNK CARD SWITCH FUNCTIONS Notes: 1. Trunk impedance switches are located on the rear face of the Trunk Card. Trunk Busy Switches 2. Outgoing Busy Switches (1 per trunk) can be set for either of the following conditions: Idle setting - normal trunk operation Busy setting - trunk cannot be seized for outgoing call 3. The “outgoing busy” condition may be set either by the outgoing busy switch (Note 2), or by the console “Trunk Busy Out” function. When this condition is in effect the incoming Busy Switch affects the trunk condition as follows: Idle setting - no answer will be given to incoming trunk calls Busy setting - a permanent seizure condition is given towards the trunk. TABLE 4-4 E&M TRUNK MODULE SWITCH SETTINGS Switch Positions Function 12345678 Digital PABX to Line Gain (3 dB) oxxxxxxx Digital PABX to Line Gain (-13 dB) lxxxxxxx Line to Digital PABX Gain (-4 dB) xoxxxxxx Line to Digital PABX Gain (-11 dB) xlxxxxxx 600 Ohm Termination xx10xxxx Complex Termination xx01xxxx 2-Wire Transmission xxxxlxxx 4-Wire Transmission xxxxoxxx Type 1 Signaling xxxxxlxx Type 5 Signaling xxxxxoxx Note: 0 = Open, 1 = Closed and x = Not Applicable. Page 4-1 O/l 0
Installation Forms 5. CABLING AND CROSS-CONNECTIONS General 5.01 The forms contained in this Part show the plug assignments for each circuit of each bay. The first four forms cover the four bays in the all-digital configuration. Plug assignment forms are also included for analog Bay 3 and Peripheral Cabinet, if needed. Power Fail Transfer card assignment forms are included for both Control and Peripheral cabinets. For more information, refer to Section MITL9108-093-200-NA, Shipping, Receiving and Installation Informa- tion. Page 5-l
Installation Forms PLUG 57 (at Cross-Connect Field) BAY 1 TABLE 5-l PLUG ASSIGNMENTS Bay/ Pair Connection/Comments Slot Cct Pin Colour (Extension, Circuit, Feature) I-2 26 W-BL 1 BL-W 27 w-o 2 o-w 26 W-G 3 G-W 29 W-BR 4 BR-W 30 W-S 5 S-W 31 R-BL 6 BL-R 32 R-O 7 O-R 33 R-G 6 G-R 34 R-BR 9 BR-R 35 R-S 10 S-R 36 BK-BL 11 BL-BK 37 BK-0 12 0-BK 36 BK-G Not Used 13 G-BK Not Used l-l 39 BK-BR 14 BR-BK 40 BK-S 15 S-BK 41 Y-BL 16 BL-Y 42 Y-O 17 O-Y 43 Y-G 18 G-Y 44 Y-BR 19 BR-Y 45 Y-S 20 S-Y 46 V-BL 21 BL-V 47 v-o 22 o-v 48 V-G 23 G-V 49 V-BR 24 BR-V 50 v-s 25 s-v Note: Specify the appropriate Circuit number to match the card type. Page 5-2
Installation Forms TABLE 5-l (CONT’D) BAY 1 PLUG ASSIGNMENTS PLUG Jll (at Cross-Connect Field) Bay/ Pair Slot Cct Pin Colour Connection/Comments (Extension, Circuit, Feature) l-4 l-3 26 1 27 2 28 3 29 4 30 5 31 6 32 7 33 8 34 9 35 10 36 11 37 12 38 13 39 14 40 15 41 16 42 17 43 18 44 19 45 20 46 21 47 22 48 23 49 24 50 25 W-EL EL-W w-o o-w W-G G-W W-BR BR-W w-s S-W R-BL BL-R R-O O-R R-G G-R R-BR BR-R R-S S-R BK-BL BL-BK BK-0 0-BK BK-G G-BK BK-BR BR-BK BK-S S-BK Y-BL BL-Y Y-O O-Y Y-G G-Y Y-BR BR-Y Y-S S-Y V-BL BL-V v-o o-v V-G G-V V-BR BR-V v-s s-v Not Used Not Used Note: Specify the appropriate Circuit number to match the card type. Page 5-3
Installation Forms TABLE 5-1 (CONT’D) BAY 1 PLUG ASSIGNMENTS PLUG J5 (at Cross-Connect Field) Bay/ Pair Connection/Comments Slot Cct Pin Colour (Extension, Circuit, Feature) l-6 26 W-BL 1 BL-W 27 w-o 2 o-w 26 W-G 3 G-W 29 W-BR 4 BR-W 30 w-s 5 S-W 31 R-BL 6 BL-R 32 R-O 7 O-R 33 R-G 8 G-R 34 R-BR 9 BR-R 35 R-S IO S-R 36 BK-BL 11 BL-BK 37 BK-0 12 0-BK 38 BK-G Not Used 13 G-BK Not Used l-5 39 BK-BR 14 BR-BK 40 BK-S 15 S-BK 41 Y-BL 16 BL-Y 42 Y-O 17 O-Y 43 Y-G 18 G-Y 44 Y-BR 19 BR-Y 45 Y-S 20 S-Y 46 V-BL 21 BL-V 47 v-o 22 o-v 48 V-G 23 G-V 49 V-BR 24 BR-V 50 v-s 25 s-v Note: Specify the appropriate Circuit number to match the card type. Page 5-4
Installation Forms TABLE 5-l (CONT’D) BAY 1 PLUG ASSIGNMENTS PLUG J9 (at Cross-Connect Field) Bay/ Pair Connection/Comments Slot Cct Pin Colour (Extension, Circuit, Feature) I-8 26 W-BL 1 BL-W 27 w-o 2 o-w 28 W-G 3 G-W 29 W-BR 4 BR-W 30 w-s 5 s-w 31 R-BL 6 BL-R 32 R-O 7 O-R 33 R-G 8 G-R 34 R-BR 9 BR-R 35 R-S 10 S-R 36 BK-BL 11 BL-BK 37 BK-0 12 0-BK 38 BK-G Not Used 13 G-BK Not Used l-7 39 BK-BR 14 BR-BK 40 BK-S 15 S-BK 41 Y-BL 16 BL-Y 42 Y-O 17 O-Y 43 Y-G 18 G-Y 44 Y-BR 19 BR-Y 45 Y-S 20 S-Y 46 V-BL 21 BL-V 47 v-o 22 o-v 48 V-G 23 G-V 49 V-BR 24 BR-V 50 v-s 25 s-v Note: Specify the appropriate Circuit number to match the card type. Page 5-5
Installation Forms TABLE 5-2 BAY 2 PLUG ASSIGNMENTS PLUG J31 (at Cross-Connect Field) Bay/ Slot Cct 2-2 Pair Connection/Comments Pin Colour (Extension, Circuit, Feature) 26 W-BL 1 BL-W 27 w-o 2 o-w 26 W-G 3 G-W 29 W-BR 4 BR-W 30 W-S 5 s-w 31 R-BL 6 BL-R 32 R-O 7 O-R 33 R-G 8 G-R 34 R-BR 9 BR-R 35 R-S 10 S-R 36 BK-BL 11 BL-BK 37 BK-0 12 0-BK 38 BK-G Not Used 13 G-BK Not Used 39 BK-BR 2-l 14 BR-BK 40 BK-S 15 S-BK 41 Y-BL 16 BL-Y 42 Y-O 17 O-Y 43 Y-G 18 G-Y 44 Y-BR 19 BR-Y 45 Y-S 20 S-Y 46 V-BL 21 BL-V 47 v-o 22 o-v 48 V-G 23 G-V 49 V-BR 24 BR-V 50 v-s 25 s-v Note: Specify the appropriate Circuit number to match the card type. Page 5-6