Mitel SX-200 DIGITAL Pabx Information Manual

							Shipping, Receiving, And Installation Information 
2.04 The maximum ports available for each configuration are: 
Bays I,2 144 voice/data ports 
Bays 1,2,3 240 voice/data ports 
Bays 1.2.3.4 336 voice/data ports 
2.05 Both configurations are compatible with most existing station, 
key telephone, private branch exchange, and central office 
equipment, and provide: 
- use of a flexible numbering plan 
- simultaneous use of DTMF and rotary dial stations 
- optional use of attendant consoles 
- extensive selection of standard and optional features 
- data port facility for traffic analysis and other requirements 
- automatic diagnostics 
- six to 36 power fail transfer trunks - max 18 PFT (336 ports) 
- max 24 PFT (480 ports) 
- optional reserve power supply or uninterruptible power supply 
- SUPERSET 3TM set 
- SUPERSET qTM set. 
Control Cabinet 
2.06 The SX-200@ DIGITAL PABX Control cabinet consists of a metal 
frame enclosed by back, top, and side panels. The digital Con- 
trol shelf in the lower position has two Bays; Bay 1 is on the left, and 
Bay 2 on the right. Access to the Bays is through the front door of the 
cabinet. The rear panel allows access to line, trunk, and PCM cable 
entries. Figure 2-3 shows an SX-200@ DIGITAL PABX Universal Control 
Cabinet; Figure 2-4 shows an SX-200* DIGITAL PABX in a Universal 
Control Cabinet. 
Universal Cabinet 
2.07 The Universal cabinet is similar to the existing Control cabinet. 
The major differences are: its maintenance panel is located 
immediately above the digital Control shelf, its Floppy Disk Drive plugs 
directly into the backplane, it can have a digital Peripheral shelf, and its 
Main Control Card directly controls up to three 6-circuit Power Fail 
Transfer cards. Figure 2-5 shows an SX-200@ DIGITAL PABX Universal 
Control Cabinet with Digital Peripheral Shelf. 
Single Cabinet System 
2.08 The Control cabinet contains a digital Control shelf in the lower 
position and a maintenance panel at the top of the cabinet. The 
Control shelf has Bay 1 on the left and Bay 2 on the right. The PABX 
can be expanded by adding a 120-port shelf (Bay 3), which contains 
Page 2-2  
						

							Shipping, Receiving, And installation Information 
three control cards and up to 15 voice cards, above the Control shelf. 
A standard SX-200@ power supply is also installed concurrently, re- 
placing the rear door of the cabinet. 
The SX-200@ PABX in the Universal cabinet is similar, but can be 
expanded by installing either an analog peripheral shelf or a digital 
peripheral shelf in the upper shelf. If an analog shelf (120-port) is 
installed (Generics 1000 and IOOl), a Peripheral cabinet may also be 
connected, adding an additional 216 ports to the PABX. If a digital shelf 
(2 x 96 ports) is installed (Generic IOOl), Bays 3 and 4 are each similar 
to Bay 1, except with the addition of Bay Control card. 
Peripheral Cabinet 
2.09 The Peripheral cabinet (shown in Figure 2-6) is an SX-200@ 
cabinet with one or two shelves (Bays) equipped with Control 
cards and Peripheral cards. 
480-Port Configuration 
2.10 The 480-port configuration can be equipped as follows: 
Bay Control Card(s) Optional Peripheral Cards 
1 BPS ONS, LS/GS, Universal, COV, DID, OPS (up to 08) 
2 MCC, BPS, FDD 
ONS, LWGS, Universal, COV, DID, OPS (up to 04) 
3 DIC, PCC, Scanner CO Trk, Line, SUPERSET, E&M Trk, DID/Tie (up to 
15) 
4 
DIC, PCC, Scanner CO Trk, Line, SUPERSET, E&M Trk, DID/Tie (up to 
15) 
5 DIC CO Trk, Line, SUPERSET, E&M Trk, DID/Tie (up to 
12) 
Note: Each bay in use must have all its Control cards present. 
Peripheral cards are installed as required. 
Card Type Description 
MCC Main Control Card 
BPS Bay Power Supply 
FDD Floppy Disk Drive 
ONS On-premises Line Card (12 circuit) 
LWGS Loop Start / Ground Start CO Trunk Card (6 cir- 
cuit) 
Universal 
DID Universal Card (accepts up to four modules) 
Direct Inward Dial Trunk Card (6 circuit) 
Page 2-3  
						

							Shipping, Receiving, And Installation Information 
OPS 
cov 
CO Trk 
Line 
SUPERSET 
E&M Trk 
DID/Tie 
336-Port Configuration 
Off-premises Line Card (6 circuit) 
Control Over Voice Line Card (6 circuit) (for 
SUPERSETB sets) 
CO Trunk Card (4 circuit) 
Line Card (8 circuit) 
SUPERSET@ set Line Card (6 circuit) 
E&M Trunk Card (2 circuit) 
Direct Inward Dial or Tie Trunk (2 circuit). 
2.11 If a digital shelf is added to the Universal Cabinet, the SX-200@ 
DIGITAL 336-port configuration can be equipped as follows: 
Bav 
Control Card(s) Optional Peripheral Cards 
1 BPS ONS, LWGS, Universal, COV, DID, OPS (up to 08) 
2 MCC, BPS, FDD ONS, LS/GS, Universal, COV, DID, OPS (up to 04) 
3 BPS, BC ONS, LS/GS, Universal, COV, DID, OPS (up to 08) 
4 BPS, BC ONS, LWGS, Universal, COV, DID, OPS (up to 08) 
Note: Each bay in use must have all its Control cards present. 
Peripheral cards are installed as required. 
Card 
Tvw 
MCC Description 
Main Control Card 
BPS 
BC .Bay Power Supply 
Bay Controller 
FDD Floppy Disk Drive 
ONS 
LWGS 
Universal On-premises Line Card (12 circuit) 
Loop Start / Ground Start CO Trunk Card (6 circuit) 
Universal Card (accepts up to four modules) 
DID Direct Inward Dial Trunk Card (6 circuit) 
OPS 
cov Off-premises Line Card (6 circuit) 
Control Over Voice Line Card for SUPERSETasets (6 circuit) 
Page 2-4  
						

							MAIN CONTROL CABINET PERIPHERAL CONTROL CABINET 
VOICE/DATA CARDS 
6 CCT TRUNK 
12 CCT STATION 
6 CCT CONTROL OVER VOICE 
6 CCT OFF PREMISE STATION 
6 CCT DIRECT INWARD DIAL 
UNIVERSAL VOICE CARDS 
8 CCT SUPERSET 
8 CCT STATION 
4 CCT CO TRUNK 
2 CCT E&M TRUNK 2 CCT DID/TIE TRUNK  
						

							Shipping, Receiving, And Installation Information 
CONTROL CABINET 
A Y A 
T T T 
A A A A A A :: 
c c c 
c c c c j.::: 
A A A A :: .. 
R R R R :;,:. 
D D D D !:j:;. D D D D I.:::.; 
5 6 7 8 
5 6 7 6 
B ’ ” 1 v 1 v 1 v 1. i-i;:] 
VlVlVlV :i] 
^ - ^ -. 
A7 Y Y Y 
vcccc 
: : : : 
D D D D 
4 : t f t A A A A 
c c c c A A A A 
R R R R 
” ” ” 0 
:: L :: I 
: E 
: : / 
D D D D 
A A A A 
T T T T 
A A A A 
IDI DIDIDI .:: 
. . 
I 
B 
A 
V 
““Ibr, “A I A bAltY3 
6 CCT/CARD TRUNK 
12 CCT/CARD REGULAR 
6 CCT CONTROL OVER VOICE 
6 CCT OFF PREMISE STATION 
6 CCT DIRECT INWARD DIAL 
UNIVERSAL 
KAO184RZ 
Figure 2-2 SX-200@ DIGITAL PABX Bay and Slot Assignments (336-Port Configuration) 
Page 2-6  
						

							Shipping, Receiving, And Installation Information 
BAV 3 
1-I 
MAINTENANCE PANEL 
PERIPHERAL SHELF 
CONTROL SHELF 
BAV 1 
BAV 2 
/ 
PERIPHERAL 
SHELF 
REAR DOOR 
POWER SUPPLY 
KAO190RlEl 
Figure 2-3 SX-200@ DIGITAL PABX Control Cabinet 
Page 2-7  
						

							Shipping, Receiving, And Installation information 
BAY 3 POWER SWITCH 
/ 
/ PERIPHERAL SHELF 
IBAY 3) 
MAINTENANCE PANEL 
Y 
I 
- [ PERIPHERAL 
SHELF 
KAOllZRlEl  BAV 1 
I I CONTROL SHELF 
/ CONTROL 
SHELF ‘ 
- 
‘r 
 FAN ASSEMBLV 
POWER’SUPPLV 
Figure 2-4 SX-200@ Universal Control Cabinet 
Page 2-8  
						

							Shipping, Receiving, And Installation Information 
PERIPHERAL SHELF 
I1 
BAY 4 
BA’f 3 
KA0133RZE2 
I CONTROL SHELF MAINTENANCE 
/ PANEL 
FANS 
PO&El7 
DISTRIEUTION AC FILTER 
Figure 2-5 SX-200@ DIGITAL PABX Universal Control Cabinet with Digital Peripheral Shelf 
Page 2-9  
						

							Shipping, Receiving, And Installation Information 
MAINTENANCE II 
PANEL 
BAY 5 
BAY 4 --------if--i- 
CLAMP 
4- 
KA0199RlE’ 
Figure 2-6 SX-200” DIGITAL PABX Peripheral Cabinet 
Page 2-10  
						

							Shipping, Receiving, And Installation information 
Printed Circuit Cards 
2.12 All printed circuit cards are packed separately and sent in ship- 
ping cartons, five or 10 to a carton. 
CAUTION: Always wear an antistatic wrist strap when handling 
cards. Handle printed circuit cards by their edges only. 
Handling the board faces or components may cause 
damage. Do not touch the gold edge connectors. 
Each peripheral bay card has two card extractors which enable the 
card to be easily removed. Control shelf cards have only one extractor 
per card. In the closed position, the card extractors ensure that the 
circuit cards are held firmly in position. Cards which must not be 
removed or inserted while the system power is on, carry a Caution 
notice. 
Control Shelf 
2.13 Main Control Card. 
The Main Control Card (MCC) is located in 
the Control shelf between Bay 1 and Bay 2, and provides overall 
control of PABX operation. It has a digital interface, through the back- 
plane to the cards in the Control shelf, and through the PCM cable to 
the Digital Interface Cards in each Peripheral shelf. In addition, the 
MCC holds the Decryption module which is associated with the soft- 
ware (each diskette release, of system software has its own unique 
Decryption 
module). Whenever the system software release is 
changed, the Decryption module must also be changed. The MCC also 
contains alarm LEDs, RESET switch, and other system indicators. Figure 
2-7 shows the MCC and the Decryption module. The dimensions of 
this card are as follows: 325.8 mm (12.825 inches) high and 358.8 mm 
(14.125 inches) wide. Two card extractors are mounted at top and 
bottom of the front edge of the card. When the extractors are in the 
locked position, the MCC is firmly seated in three DIN connectors on 
the backplane at the rear of the shelf. 
2.14 Control Shelf Circuit Cards. The circuit cards in the Control 
shelf, other than the MCC, measure 157.5 mm (6.2 inches) high 
and 366.4 mm (14.425 inches) wide. 
2.15 
Universal Card. A Universal card can plug into any of the 
upper peripheral slots in a digital shelf. The card is capable of 
carrying four plug-in modules. 
2.16 The total power rating allowed per universal card is 10. Up to 
four modules (as long as the total power rating is 10 or less) 
may be mounted on a universal card. 
2.17 Four types of modules are available that can be plugged into 
the Universal card. These are: 
0 DTMP Receiver/Relay Module - Has four Dual-Tone Multi- 
Frequency (DTMF) receiver circuits and two relays. The relays 
Page 2-l 1