Konica Minolta bizhub C35 User Manual
Have a look at the manual Konica Minolta bizhub C35 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 346
Status, error and service messages13-41
Operator messages
[The USB device is
invalid.]
[Disconnect USB device.]An incompatible USB
device is connected to
the USB HOST port.Disconnect the USB
device from the USB
HOST port.
[IEEE802.1x Auth. failed]
[Please reboot.]IEEE 802.1X port
authentication timed
out.Turn the machine off,
then on again.
[IEEE802.1x
Authenticating]
[Please wait.]IEEE 802.1X port
authentication is being
performed.If authentication is suc-
cessful, the message is
cleared.
If...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-345.png "Page 346
Status, error and service messages13-41
Operator messages
[The USB device is
invalid.]
[Disconnect USB device.]An incompatible USB
device is connected to
the USB HOST port.Disconnect the USB
device from the USB
HOST port.
[IEEE802.1x Auth. failed]
[Please reboot.]IEEE 802.1X port
authentication timed
out.Turn the machine off,
then on again.
[IEEE802.1x
Authenticating]
[Please wait.]IEEE 802.1X port
authentication is being
performed.If authentication is suc-
cessful, the message is
cleared.
If...")
![Page 347
Status, error and service messages 13-42
[Toner Cartridge Missing]
[install toner cartridge and
close all doors.]No toner cartridge is
installed. Otherwise, a
toner cartridge
incompatible with the
machine has been
installed.Install the correct toner
cartridge.
[Waste Toner Box Full]
[Replace waste toner box
by following the instruc-
tion.]The waste toner bottle
is full.Replace the waste
toner bottle.
[Replace Imaging Unit]
[Open front door and
replace imaging unit by
following the...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-346.png "Page 347
Status, error and service messages 13-42
[Toner Cartridge Missing]
[install toner cartridge and
close all doors.]No toner cartridge is
installed. Otherwise, a
toner cartridge
incompatible with the
machine has been
installed.Install the correct toner
cartridge.
[Waste Toner Box Full]
[Replace waste toner box
by following the instruc-
tion.]The waste toner bottle
is full.Replace the waste
toner bottle.
[Replace Imaging Unit]
[Open front door and
replace imaging unit by
following the...")
![Page 348
Status, error and service messages13-43
[Replenish paper]
[Replenish paper in Tray x
or select other paper tray.]There is no paper in
the paper tray
selected for printing.
(when [Auto Tray
Switching] is set to
[OFF])Load paper into the
specified paper tray.
[Paper Size/Type
Mismatch]
[Load the following paper in
tray x.]
[Paper : xxxxx xxxxx]The type and size of
the paper loaded into
all of the paper trays
are different. (when
[Auto Tray Switching]
is set to [ON])Load the specified...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-347.png "Page 348
Status, error and service messages13-43
[Replenish paper]
[Replenish paper in Tray x
or select other paper tray.]There is no paper in
the paper tray
selected for printing.
(when [Auto Tray
Switching] is set to
[OFF])Load paper into the
specified paper tray.
[Paper Size/Type
Mismatch]
[Load the following paper in
tray x.]
[Paper : xxxxx xxxxx]The type and size of
the paper loaded into
all of the paper trays
are different. (when
[Auto Tray Switching]
is set to [ON])Load the specified...")
![Page 349
Status, error and service messages 13-44
[Check Scanner Lock
Lever]
[Unlock the scanner lock
lever.]The scanner is locked. Cancel the job.
Unlock the scanner.
For details, refer to
“Unlocking the Scan-
ner” on page 13-3.
[Place Original on Glass]
[Unable to scan from ADF
with this original size.]The selected
document size cannot
be scanned from the
ADF.Place the document on
the original glass if it
has a size that cannot
be scanned from the
ADF.
[Place Original on ADF]
[Place originals on the...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-348.png "Page 349
Status, error and service messages 13-44
[Check Scanner Lock
Lever]
[Unlock the scanner lock
lever.]The scanner is locked. Cancel the job.
Unlock the scanner.
For details, refer to
“Unlocking the Scan-
ner” on page 13-3.
[Place Original on Glass]
[Unable to scan from ADF
with this original size.]The selected
document size cannot
be scanned from the
ADF.Place the document on
the original glass if it
has a size that cannot
be scanned from the
ADF.
[Place Original on ADF]
[Place originals on the...")
![Page 350
Status, error and service messages13-45
[Memory Full (Scan)]
[Insufficient memory.]
[The job is cancelled.]The memory capacity
is insufficient.
Otherwise, the SSD
storage area is
insufficient.Cancel the job.
[HDD Capacity Over]
[Insufficient HDD capacity.]
[Delete unnecessary file.]
[The job is cancelled.]There is not enough
space available on the
hard disk.Delete any unneces-
sary files.
Cancel the job.
[Document Registration
Limit Over]
[Saved documents in folder
reached limit.]
[The job is...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-349.png "Page 350
Status, error and service messages13-45
[Memory Full (Scan)]
[Insufficient memory.]
[The job is cancelled.]The memory capacity
is insufficient.
Otherwise, the SSD
storage area is
insufficient.Cancel the job.
[HDD Capacity Over]
[Insufficient HDD capacity.]
[Delete unnecessary file.]
[The job is cancelled.]There is not enough
space available on the
hard disk.Delete any unneces-
sary files.
Cancel the job.
[Document Registration
Limit Over]
[Saved documents in folder
reached limit.]
[The job is...")
![Page 351
Status, error and service messages 13-46
[I-Fax RX failed]
[Failed to complete the job
due to an error while I-FAX
RX.]
[Check the log.]The job did not end
normally because an
error occurred during
I-FAX RX.Check the log.
[I-Fax TX failed]
[I-FAX TX failed due to
error.]
[Redial will be attempted
after predetermined time
progress.]The job did not end
normally because an
error occurred during
I-FAX TX.A document is sent
again after the specified
time period has lapsed. Message Cause Solution...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-350.png "Page 351
Status, error and service messages 13-46
[I-Fax RX failed]
[Failed to complete the job
due to an error while I-FAX
RX.]
[Check the log.]The job did not end
normally because an
error occurred during
I-FAX RX.Check the log.
[I-Fax TX failed]
[I-FAX TX failed due to
error.]
[Redial will be attempted
after predetermined time
progress.]The job did not end
normally because an
error occurred during
I-FAX TX.A document is sent
again after the specified
time period has lapsed. Message Cause Solution...")
![Page 352
Status, error and service messages13-47 Service messages
These messages indicate a more serious problem that can only be corrected
by a service representative. If one of these messages appears, turn the
machine off, then on again. If the problem persists, contact your local vendor
or authorized service provider.
Message Cause Solution
[Service Call]
[Error occurred. Power
OFF and ON, or contact
Service with Trouble
Code;xxxx]An error has been
detected with the item
indicated by “xxxx” in
the...](http://img.usermanuals.tech/thumb/2790/37230/w64_Konica_Minolta_bizhub_C35-351.png "Page 352
Status, error and service messages13-47 Service messages
These messages indicate a more serious problem that can only be corrected
by a service representative. If one of these messages appears, turn the
machine off, then on again. If the problem persists, contact your local vendor
or authorized service provider.
Message Cause Solution
[Service Call]
[Error occurred. Power
OFF and ON, or contact
Service with Trouble
Code;xxxx]An error has been
detected with the item
indicated by “xxxx” in
the...")
Status, error and service messages 13-46 [I-Fax RX failed] [Failed to complete the job due to an error while I-FAX RX.] [Check the log.]The job did not end normally because an error occurred during I-FAX RX.Check the log. [I-Fax TX failed] [I-FAX TX failed due to error.] [Redial will be attempted after predetermined time progress.]The job did not end normally because an error occurred during I-FAX TX.A document is sent again after the specified time period has lapsed. Message Cause Solution Downloaded From ManualsPrinter.com Manuals
Status, error and service messages13-47 Service messages These messages indicate a more serious problem that can only be corrected by a service representative. If one of these messages appears, turn the machine off, then on again. If the problem persists, contact your local vendor or authorized service provider. Message Cause Solution [Service Call] [Error occurred. Power OFF and ON, or contact Service with Trouble Code;xxxx]An error has been detected with the item indicated by “xxxx” in the service message.Restart the machine. This often clears the service message, and machine operation can resume. If the problem persists, contact the service rep- resentative. Downloaded From ManualsPrinter.com Manuals
Status, error and service messages 13-48 Downloaded From ManualsPrinter.com Manuals
14 Installing Accessories Downloaded From ManualsPrinter.com Manuals
Introduction 14-2 Introduction Note Use of accessories not manufactured or supported by KONICA MINOLTA will void your warranty. For details of accessories, visit our web site (http://konicami- nolta.com) Lower Feeder Unit (Tray 3/Tray 4)500-sheet tray included Working Table WT-P01Provides an area to temporarily place an original or install an authentication device. Downloaded From ManualsPrinter.com Manuals
Lower Feeder Unit PF-P0814-3 Lower Feeder Unit PF-P08 You can install up to one optional lower feeder unit PF-P08 (Tray 3/4). The lower feeder unit PF-P08 increases your machine’s media feed capacity by 500 sheets. Kit Contents „Lower feeder unit with a tray (500-sheet capacity) Downloaded From ManualsPrinter.com Manuals
Lower Feeder Unit PF-P08 14-4 Installing a Lower Feeder Unit PF-P08 Note Since consumables are installed in the machine, be sure to keep the printer level when moving it in order to prevent accidental spills. 1Turn off the machine and discon- nect the power cord and inter- face cables. 2Prepare the lower feeder unit. Be sure to place the lower feeder unit on a level surface. 3Open the right side cover of the lower feeder unit. The right side cover of the lower feeder must be opened before the feeder can be installed onto the machine. Downloaded From ManualsPrinter.com Manuals
Lower Feeder Unit PF-P0814-5 4With another person’s help, place the machine on top of the lower feeder unit, making sure that the positioning pins on the lower feeder unit correctly fit into the holes on the bottom of the machine. WARNING! This machine weighs approximately 39 kg (86 lbs) when it is fully loaded with consumables. The machine must be lifted by two people. 5Close the right side cover of the lower feeder unit. 6Reconnect all interface cables. 39 kg 86 lbs Downloaded From ManualsPrinter.com Manuals
Working Table WT-P01 14-6 7Reconnect the power cord, and turn on the machine. 8Declare Paper Source Unit 3/4 in the Windows printer driver [Properties]/ [Configure] tab. Working Table WT-P01 Provides an area to temporarily place an original or other materials. This is also used when the authentication device is installed. Kit Contents a—Working table b—Mounting plate Downloaded From ManualsPrinter.com Manuals
Working Table WT-P0114-7 c—Four screws d—Two screws e—Two clamps Use this part when installing the Authentication Device (IC card type). Store the part in a safe place for future use. Installing a Working Table WT-P01 1Using a coin, turn the screws (c) to install the mounting plate. c b Downloaded From ManualsPrinter.com Manuals