Konica Minolta bizhub C35 User Manual

							[Admin Settings] 3-64
[Halftone 256] Settings[Print] / [Cancel]
Prints the halftone pattern using a 100% den-
sity for each CMYK color.
[Cyan 256]/
[Magenta 256]/
[Yellow 256]/
[Black 256]
[Gradation] Settings[Print] / [Cancel]
Prints the gradation pattern.
[Activity Report] Settings[Print] / [Cancel]
Prints the communications activity report.
[Scan Send Report 
Print]Settings[Print] / [Cancel]
Prints the scanning operations activity report.
[Scan Event Log] Settings[Print] / [Cancel]
Prints the scanning event log.
[Printer Adjustment] Specify various machine adjustments.
[Leading Edge Adjust-
ment]Adjust the top margin for various types of 
media.
[Plain Paper] Settings -15 to 15
Adjust the top margin of plain paper for simplex 
(single-sided) printing.
[Thick 1] Settings -15 to 15
Adjust the top margin of thick paper for simplex 
(single-sided) printing.
[Thick 2] Settings -15 to 15
Adjust the top margin of Thick 2 paper for sim-
plex (single-sided) printing.
[Envelope] Settings -15 to 15
Adjust the top margin of envelopes for simplex 
(single-sided) printing.
[Side Edge Adjustment] Adjust the left margin for media fed from each 
paper tray.
[Tray1] Settings -15 to 15
Adjust the left margin of media fed from Tray 1 
for simplex (single-sided) printing.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings]3-65
[Tray2] Settings -15 to 15
Adjust the left margin of media fed from Tray 2 
for simplex (single-sided) printing.
[Tray3] Settings -15 to 15
Adjust the left margin of media fed from Tray 3 
for simplex (single-sided) printing.
[Tray4] Settings -15 to 15
Adjust the left margin of media fed from Tray 4 
for simplex (single-sided) printing.
[Left ADJ Duplex] Adjust the left margin for media fed from each 
paper tray with duplex (double-sided) printing.
[Tray1] Settings -15 to 15
Adjust the left margin of media fed from Tray 1 
for duplex (double-sided) printing.
[Tray2] Settings -15 to 15
Adjust the left margin of media fed from Tray 2 
for duplex (double-sided) printing.
[Tray3] Settings -15 to 15
Adjust the left margin of media fed from Tray 3 
for duplex (double-sided) printing.
[Tray4] Settings -15 to 15
Adjust the left margin of media fed from Tray 4 
for duplex (double-sided) printing.
[2nd Image Transfer 
Current]Adjust the 2nd image transfer current.
[Simplex Pass] Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing.
[Plain Paper] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of plain 
paper.
[Thick 1] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of Thick 1 
paper.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings] 3-66
[Thick 2] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of Thick 2 
paper.
[Postcard] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of postcards.
[Envelope] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of envelopes.
[Label] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of labels.
[Glossy 1] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of Glossy 1 
media.
[Glossy 2] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for simplex (single-sided) printing of Glossy 2 
media.
[Manual Duplex] Adjust the 2nd image transfer output (ATVC) 
for duplex (double-sided) printing.
[Plain Paper] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of plain paper that 
has already been printed on.
[Thick 1] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of Thick 1 paper 
that has already been printed on.
[Thick 2] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of Thick 2 paper 
that has already been printed on.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings]3-67
[Postcard] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of postcards that 
has already been printed on.
[Envelope] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of envelopes that 
has already been printed on.
[Label] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of labels that has 
already been printed on.
[Glossy 1] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of Glossy 1 media 
that has already been printed on.
[Glossy 2] Settings -8 to 7
Adjust the 2nd image transfer output (ATVC) 
for printing on the back side of Glossy 2 media 
that has already been printed on.
[Thick Paper Image 
Density]Adjust the density of images printed on thick 
paper.
[Cyan] Settings -5 to 5 (Default: 0)
Finely adjust the density of cyan for images 
printed on thick paper.
[Magenta] Settings -5 to 5 (Default: 0)
Finely adjust the density of magenta for images 
printed on thick paper.
[Yellow] Settings -5 to 5 (Default: 0)
Finely adjust the density of yellow for images 
printed on thick paper.
[Black] Settings -5 to 5 (Default: 0)
Finely adjust the density of black for images 
printed on thick paper.
[Monochrome Density 
Adj.]Settings -2 to 2 (Default: 0)
Finely adjust the density of printed images with 
grayscale printing.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings] 3-68
[Fine Line ADJ] Settings -3 to 2 (Default: 0)
Adjust how fine lines are reproduced by chang-
ing the applied voltage (VC) to the electrostatic 
roller.
[AIDC Mode] Settings [Mode 1] / [Mode 2]
Select the AIDC operation mode.
[Mode 1]: Standard mode
[Mode 2]: Low mode
[Thick Mode] Settings[Quality Mode] / [Speed Mode]
In order to prevent toner from clogging within 
the developer unit as a result of it being driven 
at half-speed, select the timing for driving the 
developer unit at full speed for a fixed length of 
time when thick paper is being fed.
[Quality Mode]: While printing on thick paper, 
printing is periodically paused, and the devel-
oper unit is driven at full speed for a fixed 
length of time. Since printing is paused, the 
quality is not affected; however, a standby time 
of approximately 70 seconds occurs every 400 
seconds or so of half-speed operation.
[Speed Mode]: While printing on thick paper, 
only the drive of the developer unit periodically 
switches to full speed for a fixed length of time. 
Since printing continues during full-speed 
drive, the print quality is slightly affected, how-
ever the standby time is short.
[Engine DipSW] Change the DIP switches to control machine 
operation.
[Engine DipSW 1] - 
[Engine DipSW 28]Settings [ON] / [OFF]
Use to change engine settings.
Normally, there is no need to change the 
settings. If it becomes necessary to 
change the settings, do so according to 
the instructions from the service 
representative.
Downloaded From ManualsPrinter.com Manuals 
						

							
[Admin Settings]3-69
[Folder Settings]

All factory default values are shown in bold.
[Main Scan Adjust] Adjust the scanning settings.
[Main Scan Page] Settings [Print] / [Cancel]
Print the test pattern for fine adjustment of the 
color ratios in the main scanning direction.
[Scan Adjust Value] Specify color  adjustments for yellow, magenta 
and cyan.
[Yellow] Settings -42 to 42 (Default:  0)
Finely adjust the ratio of yellow in the main 
scanning direction.
[Magenta] Settings -42 to 42 (Default:  0)
Finely adjust the ratio of magenta in the main 
scanning direction.
[Cyan] Settings -42 to 42 (Default:  0)
Finely adjust the ratio of cyan in the main scan-
ning direction.
[Supplies] Reset the service li fe counters for various con-
sumables.
[Consumables Replace]
[Transfer Belt Unit] Settings [Yes] /  [No]
Reset the transfer belt counter.
[Transfer Roller 
Unit] Settings [Yes] / 
[No]
Reset the transfer roller counter.
[Fusing Unit] Settings [Yes] /  [No]
Reset the fuser unit counter.
Item Description
[Auto Del Interval] Settings [Erase Disabled] / [12 Hours] / [1 
Day] / [2 Days] / [3 Days] / [7 Days] 
/ [30 Days]
Select the periodic time interval to automati-
cally delete all files saved on the hard disk 
using the Scan to HDD function.
Downloaded From ManualsPrinter.com Manuals 
						

							
[Admin Settings]
3-70
[Security Settings]
 All factory default values are shown in bold.
[Auto Document Delete 
Time]
Settings [Erase Disabled] / [12 Hours] / 
[1 
Day]  / [2 Days] / [3 Days] / [7 Days] 
/ [30 Days]
Select the time period after which to automati-
cally delete each file saved on the hard disk 
using the Scan to HDD function.
[Document Hold Setti ng] Settings [Enable] /  [Disable]
Select whether or not a file is deleted after it is 
retrieved.
Item Description
[Administrator Password] Settings [12345678]
Change the administrator password.
Specify the administrator password as a 0 to 8 
digit number.
 If password rules have been applied, an 
8-digit password must be specified.
If the administrator password is 
incorrectly entered th ree times, machine 
operations are locked. If this occurs, turn 
the machine off, then on again.
[Password] (top): Type in the current password.
[Password] (bottom): Type in the new pass-
word.
[Security Details] Specify detailed security settings to limit  machine functions. Security can be enhanced if 
machine functions are limited.
[Password Rules] Settings [ON] /  [OFF]
Select whether or not password rules are 
applied.
[Registering and 
Changing Addr.] Settings
[Allow] / [Restrict]
Select whether or not to  prohibit editing of the 
address book. If [Restrict] is selected, the 
address book cannot be edited.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings]3-71
[Manual Destination 
Input]Settings[Allow] / [Restrict]
Select whether or not to prohibit manual input 
of a destination. If [Restrict] is selected, desti-
nations for fax and scan operations cannot be 
entered directly.
[Hide Personal Data] Settings [ON] / [OFF]
Select whether or not to display transmission 
destinations in the job log. If [ON] is selected, 
transmission destinations are not displayed.
[Disable Job History 
Display]Settings [ON] / [OFF]
Select whether or not to display the communi-
cation log. If [ON] is selected, the communica-
tion log is not displayed.
[Restrict Scan to USB] Settings[Allow] / [Restrict]
Select whether or not to prohibit the Scan to 
USB function. If [Restrict] is selected, the Scan 
to USB function cannot be used.
[Enhanced Security Mode] Settings [ON] / [OFF]
Select whether or not to apply enhanced secu-
rity settings. If [ON] is selected, the enhanced 
security settings are applied.
[HDD Settings] Check the capacity of the hard disk or delete 
data by overwriting.
[Check HDD Capacity] Check the total capacity of the hard disk, the 
amount of space used and the amount of 
space available.
[Overwrite All Data] Delete all data on the hard disk by overwriting 
it.
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings] 3-72
[Mode] Settings[Mode 1] / [Mode 2] / [Mode 3] / 
[Mode 4] / [Mode 5] / [Mode 6] / 
[Mode 7] / [Mode 8]
Select the method for overwriting the data on 
the hard disk.
[Mode 1]: Overwritten with 0x00
[Mode 2]: Overwritten with 1-byte random num-
bers   Overwritten with 1-byte random num-
bers   Overwritten with 0x00
[Mode 3]: Overwritten with 0x00   Overwritten 
with 0xff   Overwritten with 1-byte random 
numbers  Verified
[Mode 4]: Overwritten with 1-byte random num-
bers   Overwritten with 0x00   Overwritten 
with 0xff
[Mode 5]: Overwritten with 0x00   Overwritten 
with 0xff   Overwritten with 0x00   Overwrit-
ten with 0xff
[Mode 6]: Overwritten with 0x00   Overwritten 
with 0xff   Overwritten with 0x00   Overwrit-
ten with 0xff   Overwritten with 0x00   Over-
written with 0xff   Overwritten with specified 
512-byte data
[Mode 7]: Overwritten with 0x00   Overwritten 
with 0xff   Overwritten with 0x00   Overwrit-
ten with 0xff   Overwritten with 0x00   Over-
written with 0xff   Overwritten with 0xaa
[Mode 8]: Overwritten with 0x00   Overwritten 
with 0xff   Overwritten with 0x00   Overwrit-
ten with 0xff   Overwritten with 0x00   Over-
written with 0xff   Overwritten with 0xaa   
Ve r i f i e d
Downloaded From ManualsPrinter.com Manuals 
						

							[Admin Settings]3-73
[Execute] Press to delete all data on the hard disk by 
overwriting it, and then press [OK].
Perform this operation when disposing 
of this machine.
While the data is being deleted by being 
overwritten, do not use the power switch 
to turn the machine off and on.
After the machine is restarted, all data is 
deleted by being overwritten.
The following data is deleted.
– Registered user and account data
– Registered information for secured print-
ing and saved files
– Image files
[SSD Low-level Format] Press to delete all data on the SSD by overwrit-
ing it, and then press [OK].
Perform this operation when disposing 
of this machine.
While the data is being deleted by being 
overwritten, do not use the power switch 
to turn the machine off and on.
After the machine is restarted, all data is 
deleted by being overwritten.
The following data is deleted.
– Sent and received fax data
– Address book (E-mail address and tele-
phone number destination data)
– S/MIME certificates
– Image files
Downloaded From ManualsPrinter.com Manuals