Home > Konica > Printer > Konica Minolta bizhub C35 User Manual

Konica Minolta bizhub C35 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Konica Minolta bizhub C35 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 394
    							Replacing Consumables 11-28
    16Install the all toner cartridges, all 
    imaging units and waste toner 
    bottle.
    For details on installing 
    the toner cartridges, 
    imaging units or waste 
    toner bottle, refer to 
    “Replacing a Toner Car-
    tridge” on page 11-4 or 
    “Replacing a Imaging 
    Unit” on page 11-9.
    17Close the front cover.
    When closing the front 
    cover, press the area of 
    the cover with small pro-
    jections.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables11-29
    18Reconnect the power cord, and 
    turn on the machine.
    19Reset the counter in the [Admin Settings]/[Maintenance Menu]/[Supplies]/
    [Consumables Replace]/[Transfer Belt Unit] menu.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables 11-30
    Replacing the Backup Battery
    When the backup battery is at its end of life, the machine’s date and time can-
    not be retained. Follow the procedure described below to replace the backup 
    battery.
    Note
    Only use the coin-shaped 3V lithium battery CR2032. It’s very important 
    to protect the machine controller board and any associated circuit 
    boards from electrostatic damage. Before performing this procedure, 
    review the antistatic caution on page 11-38. In addition, always handle 
    circuit boards by the edges only.
    1Turn off the machine and discon-
    nect the power cord and inter-
    face cables.
    2Remove the cover.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables11-31
    3Using a coin, remove a screw.
    4Open the cover.
    5Remove the hook, and then 
    remove the backup battery.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables 11-32
    6Remove the hook, and then 
    insert a new backup battery.
    When inserting the new 
    backup battery, be sure 
    that the + side faces tow-
    erd the left.
    Risk of explosion if bat-
    tery is replaced by an 
    incorrect type. Dispose of 
    used batteries according 
    to your local regulations. 
    Do not burn the backup 
    battery.
    7Reinstall the panel and tighten a screw.
    8Install the cover.
    9Reconnect all interface cables.
    10Reconnect the power cord, and 
    turn on the machine.
    11Use [Date(XX. XX. XX)] on the [Admin Settings]/[Machine Settings]/
    [Date & Time Settings] menu to set the date, and use [Time] on the 
    [Admin Settings]/[Machine Settings]/[Date & Time Settings] menu to set 
    the time.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables11-33 Replacing the Fuser Unit
    When the time to replace the fuser unit is reached, the message [Replace 
    fusing unit.] appears. Printing can continue even after this message appears; 
    however, since the print quality is reduced, the fuser unit should be replaced 
    immediately
    1Turn off the machine.
    Note
    There are extremely hot parts within the machine. Before replacing the 
    fuser unit, wait about 20 minutes after turning off the machine, and then 
    check that the fusing section has reached room temperature, otherwise, 
    you may get burnt.
    2Pull the lever, and then open the 
    right door.
    Before opening the right 
    door, fold up Tray 1.
    3Open the fuser unit cover.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables 11-34
    4Pull down the 2 levers. 
    5Remove the fuser unit.
    6Prepare a new fuser unit.
    Be careful not to touch the 
    surface of the fuser roller.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables11-35
    7Lift up the 2 levers.
    8Remove the packing material.
    9Push down the 2 levers.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables 11-36
    10Pull down the 2 levers of a new 
    fuser unit.
    11Insert the fuser unit until it locks 
    into place.
    12Lift up the 2 levers.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Replacing Consumables11-37
    13Close the fuser unit cover.
    14Close the right door.
    If the door cannot be closed, 
    check that the fuser unit is 
    fully inserted.
    15Reset the counter in the [Admin Settings]/[Maintenance Menu]/[Supplies]/
    [Consumables Replace]/[Fusing Unit] menu.
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Konica manuals Comments (0)

    Related Manuals for Konica Minolta bizhub C35 User Manual