Konica Minolta bizhub C35 User Manual

							[Finishing] 7-10
[Finishing]
Specify any settings for finishing outputted copies.
[Proof Copy]
Before printing a large number of copies, a single finished proof copy can be 
printed in order to be checked. Select whether or not to print a proof copy.
Proof Copy operation
When printing a proof copy, specify multiple copies.
1In the home screen, press [Copy].
2Place the document on the original glass or load it into the ADF.
For details on positioning the document, refer to “Placing a document 
on the original glass” on page 4-36 and “Loading a document into the 
ADF” on page 4-37.
3Specify the copy settings.
4Press [Proof Copy]. Item Description
[Sort] Select this setting when making multiple copies of 
documents containing multiple pages so that they 
will be automatically separated into sets of the full 
document.
[Group] Select this setting when making multiple copies of 
documents containing multiple pages so that they 
will be automatically separated into sets of each 
page.
[Auto] Select this option to automatically switch between 
[Sort] and [Group] depending on the number of 
printable sheets per copy.
[Group] is set when printing a single sheet in the 
1-sided or 2-sided mode, and [Sort] is set when 
printing multiple sheets.
Item Description
[ON] Select this setting to print a proof copy.
[OFF] Select this setting to not print a proof copy.
Downloaded From ManualsPrinter.com Manuals 
						

							[Separate Scan]7-11
5Press [ON].
6Press [OK].
7Press the [Start (Color)] key or the [Start (B&W)] key.
A single proof copy is printed.
8Check the proof copy.
If the proof copy was printed as desired, continue with step 9.
Using the keypad, the number of copies can be changed.
To print another proof copy, press [Proof Copy].
To change the settings, press [Cancel], and then perform steps 2 
through 8.
9Press [Print].
The remaining number of copies is printed.
[Separate Scan]
The scan operation can be divided into several sessions, for example, when 
all pages of a document cannot be loaded into the ADF, and then the scanned 
pages can be treated as a single copy job. In addition, the scanning location 
can be switched between the original glass and the ADF during the scanning 
operation.
Item Description
[ON] Select this setting to perform a Separate Scan 
operation.
[OFF] Select this setting to not perform a Separate Scan 
operation.
Downloaded From ManualsPrinter.com Manuals 
						

							[Separate Scan] 7-12
Scanning the document in separate batches
Do not load more pages into the ADF than the maximum number of 
pages allowed, otherwise a document misfeed or damage to the docu-
ment may occur.
When sorting or making double-sided or combined copies using the 
original glass, instead of using the Separate Scan operation, the docu-
ment can be scanned as a multiple-page document.
1In the home screen, press [Copy].
2Place the document on the original glass or load it into the ADF.
For details on positioning the document, refer to “Placing a document 
on the original glass” on page 4-36 and “Loading a document into the 
ADF” on page 4-37.
3Specify the copy settings.
4Press [Separate Scan].
5Press [ON].
6Press [OK].
7Press the [Start (Color)] key or the [Start (B&W)] key.
Scanning of the document begins.
To change the scanning settings, press [Change Settings].
8Position the next document page or pages, and then press the [Start 
(Color)] key or the [Start (B&W)] key.
Scanning of the document begins.
9Repeat step 7 until all document pages have been scanned.
10After all document pages have been scanned, press [Finish].
Downloaded From ManualsPrinter.com Manuals 
						

							[ID Copy]7-13
[ID Copy]
The back and front of a card, such as an insurance card, driver’s license or 
business card, can be scanned separately and printed together on a single 
page.
With the ID Copy operation, the zoom ratio is set to 100%.
The paper sizes that are available for copying are Letter, Legal and 
A4.
The card can only be placed on the original glass. Position the card to 
be scanned aligned at the upper-left corner of the original glass. Since 
the image is printed 4 mm from the top and left side, reposition the 
card as necessary
1In the home screen, press [Copy].
2Place the card, front side down, on the original glass.
For details on positioning the document, refer to “Placing a document 
on the original glass” on page 4-36.
3Specify the copy settings.
4Press [ID Copy].
5Press the [Start (Color)] key or the [Start (B&W)] key.
Scanning of the front side begins.
6Position the card, back side down, at the same location on the original 
glass.
To copy only the front side, press [Print].
7Press the [Start (Color)] key or the [Start (B&W)] key.
Scanning of the back side begins.
The copy is fed out.
A
B
Downloaded From ManualsPrinter.com Manuals 
						

							[Paper Margin] 7-14
[Paper Margin]
Copies can be printed with a binding margin so they can easily be stored in 
filing binders.
If part of the image is lost due to the binding margin setting, reduce the 
zoom ratio before printing copies. Item Description
[+]/[-] Specify the width of the binding margin between 
0.1 mm and 20.0 mm (0.001 inches and 0.787 
inches).
[None] Select this setting to leave no binding margin.
Downloaded From ManualsPrinter.com Manuals 
						

							[Image Quality]7-15
[Image Quality]
The quality can be adjusted for the document to be scanned.
Item Description
[Background removal] Adjust the background density when copying docu-
ments with a colored background (such as newspa-
pers or recycled paper) or thin documents where 
the back side is visible from the front side.
Adjust the background density to one of nine lev-
els. Select a setting in the + direction to darken the 
background, or select a setting in the - direction to 
lighten the background. Press [Standard] to return 
the density to the standard setting.
[Contrast] The image can be adjusted to make it softer or 
sharper.
Adjust the contrast to one of nine levels. Select a 
setting in the + direction to make the image 
sharper, or select a setting in the - direction to 
make the image softer. Press [Std.] to return the 
contrast to the standard setting.
[Sharpness] The sharpness of text and image outlines can be 
adjusted.
Adjust the sharpness to one of seven levels. Select 
a setting in the + direction to increase the sharp-
ness, or select a setting in the - direction to 
decrease the sharpness. Press [Std.] to return the 
sharpness to the standard setting.
Downloaded From ManualsPrinter.com Manuals 
						

							[Image Quality] 7-16
Downloaded From ManualsPrinter.com Manuals 
						

							8Additional copy
operations
Downloaded From ManualsPrinter.com Manuals 
						

							Interrupting a copy job 8-2
Interrupting a copy job
The current jobs can be temporarily interrupted so a document can be copied 
with different copy settings.
This is convenient for quickly making a copy.
The [Interrupt] key cannot be pressed while a document is being 
scanned.
When the [Interrupt] key is pressed, the copy settings return to their 
defaults.
1In the home screen, press [Copy].
2Place the document on the original glass or load it into the ADF.
For details on positioning the document, refer to “Placing a document 
on the original glass” on page 4-36 and “Loading a document into the 
ADF” on page 4-37.
3Press the [Interrupt] key.
The indicator on the [Interrupt] key lights up in green, and printing of the 
current job stops.
4Specify the copy settings.
5To make a color copy, press the [Start (Color)] key.
To make a black-and-white copy, press the [Start (B&W)] key.
6After the interrupting job has finished printing, press the [Interrupt] key.
The indicator on the [Interrupt] key goes off, and Interrupt mode is can-
celed.
Printing of the job that was interrupted continues.
Downloaded From ManualsPrinter.com Manuals 
						

							Copy programs8-3
Copy programs
Frequently used copy settings can be stored together as a program to easily 
be recalled later.
Storing a copy program
A maximum of 15 copy programs can be stored.
1In the home screen, press [Copy].
2Specify the copy settings.
3Press the [Mode Memory] key.
The copy programs screen appear.
4Press [Register].
5Press [Name].
6Type in the name of the copy program, and then press [OK].
For details on entering text, refer to “Entering text” on page A-8.
7Press [OK].
8Press [Cancel].
The initial Copy mode screen appears again.
Deleting a copy program
1In the home screen, press [Copy].
2Press the [Mode Memory] key.
The copy programs screen appear.
3Select the copy program to be deleted.
4Press [Delete].
5Press [Yes].
6Press [OK].
7Press [Cancel].
The initial Copy mode screen appears again.
Downloaded From ManualsPrinter.com Manuals