Konica Minolta bizhub C35 User Manual
Have a look at the manual Konica Minolta bizhub C35 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Cleaning the machine 12-10 Cleaning the Laser Lens This machine is constructed with four laser lenses. Clean all lenses as described below. The laser lens cleaning tool should be attached to the inside of the tray 2. 1Pull out the tray 2. 2Remove the cover. Since the cover will be used later, do not return it to its original position. 3Remove the cleaning tool from the tray 2. Downloaded From ManualsPrinter.com Manuals
Cleaning the machine12-11 4Close the tray 2. 5Open the machine’s front cover. 6Remove the waste toner bottle and the toner cartridge and imaging unit for the color of laser lens to be cleaned. For details on removing the toner cartridge, imaging unit or waste toner bottle, refer to “Replacing a Toner Car- tridge” on page 11-4 or “Replacing a Imaging Unit” on page 11-9. Do not tilt removed toner car- tridge, otherwise toner may spill. Do not tilt removed waste toner box, otherwise waste toner may spill. 7Attach the cover to the removed imaging unit. Downloaded From ManualsPrinter.com Manuals
Cleaning the machine 12-12 8Insert the laser lens cleaning tool into the imaging unit open- ing, pull it out, and then repeat this back and forth movement 2 or 3 times. 9Install the removed toner car- tridge, imaging unit and waste toner bottle. For details on installing the toner cartridge, imaging unit or waste toner bottle, refer to “Replacing a Toner Car- tridge” on page 11-4 or “Replacing a Imaging Unit” on page 11-9. 10Close the front cover. 11Pull out the tray 2. Downloaded From ManualsPrinter.com Manuals
Cleaning the machine12-13 12Return the laser lens cleaning tool to its holder on the inside of the tray 2. 13Close the cover. 14Close the tray 2. 15Clean between each of the laser lenses in the same way. The laser lens cleaning tool is included with the machine. Safely store the laser lens cleaning tool so that it will not be lost. Downloaded From ManualsPrinter.com Manuals
Cleaning the machine 12-14 Downloaded From ManualsPrinter.com Manuals
13 Troubleshooting Downloaded From ManualsPrinter.com Manuals
Introduction 13-2 Introduction This chapter provides information to aid you in resolving machine problems you may encounter, or at least guide you to the proper sources for help. Printing a configuration page 1 Press the [Utility/Counter] key. 2Press [User Settings]. 3Press [Print Settings]. 4Press [Print Reports]. 5Press [Configuration Page]. 6Press [Print]. 7Press [OK]. Printing the configuration page page 13-2 Unlocking the Scanner page 13-3 Preventing media misfeeds page 13-4 Understanding the media path page 13-5 Clearing media misfeeds page 13-6 Solving problems with media misfeeds page 13-23 Solving other problems page 13-26 Solving problems with printing quality page 13-31 Status, error, and service messages page 13-38 Downloaded From ManualsPrinter.com Manuals
Unlocking the Scanner13-3 Unlocking the Scanner 1 Lift open the ADF cover. 2Move the scanner lock lever to . 3Close the ADF cover. 4Turn off the machine, and then turn it on again. Downloaded From ManualsPrinter.com Manuals
Preventing Media Misfeeds 13-4 Preventing Media Misfeeds Make sure that... Media matches the machine specifications. Media is flat, especially on the leading edge. The machine is on a hard, flat, level surface. You store media in a dry location away from moisture and humidity. You always adjust the media guides in the tray after inserting the media (a guide that is not properly adjusted can cause poor print quality, media mis- feeds, and machine damage). You load the media printing-side up in the tray (many manufacturers place an arrow on the end of the wrapper to indicate the printing side). Avoid... Media that is folded, wrinkled, or excessively curled. Double feeding (remove the media and fan the sheets—they may be sticking together). Loading more than one type/size/weight of media in a tray at the same time. Overfilling the trays. Allowing the output tray to overfill (the output tray has a 250-sheet capacity— misfeeding may occur if you allow more than 250 sheets of media to accumu- late at one time). Downloaded From ManualsPrinter.com Manuals
Understanding the Media Path13-5 Understanding the Media Path Understanding media path will help you locate media misfeeds 4 Fuser unit 10 Print head unit 5 Duplex 11 Imaging unit 6 Tray 1 (Manual feed tray) 12 Transfer belt unit 7 Tray 4 (optional lower feeder unit) 13 Toner cartridge 8 Tray 3 (optional lower feeder unit) 14 Output tray 9Tray 2 4 11 12 13 14 6 5 10 9 8 7 3 12 1 ADF media feed rollers 2 Document feed tray 3 Document output tray Downloaded From ManualsPrinter.com Manuals