Hitachi Sj7002 Owners Manual

							ModBus Data Listing
Appendix B
B–38
D081 —Trip monitor 1 R Factor code 0012h 00018 (see codes in 
next table)—
R Inverter status 0013h 00019 —
R Frequency (high) 0014h 00020 0 to 40000 0.01 Hz
R Frequency (low) 0015h 00021
R Current 0016h 00022 — 0.1 A
R Voltage 0017h 00023 — 1 V
R Run time (high) 0018h 00024 — 1 hour
R Run time (low) 0019h 00025
R ON time (high) 001Ah 00026 — 1 hour
R ON time (low) 001Bh 00027
D082 —
Trip monitor 2 R Factor code 001Ch 00028 (see codes in 
next table)—
R Inverter status 001Dh 00029 —
R Frequency (high) 001Eh 00030 0 to 40000 0.01 Hz
R Frequency (low) 001Fh 00031
R Current 0020h 00032 — 0.1 A
R Voltage 0021h 00033 — 1 V
R Run time (high) 0022h 00034 — 1 hour
R Run time (low) 0023h 00035
R ON time (high) 0024h 00036 — 1 hour
R ON time (low) 0025h 00037
D083 —
Trip monitor 3 R Factor code 0026h 00038 (see codes in 
next table)—
R Inverter status 0027h 00039 —
R Frequency (high) 0028h 00040 0 to 40000 0.01 Hz
R Frequency (low) 0029h 00041
R Current 002Ah 00042 — 0.1 A
R Voltage 002Bh 00043 — 1 V
R Run time (high) 002Ch 00044 — 1 hour
R Run time (low) 002Dh 00045
R ON time (high) 002Eh 00046 — 1 hour
R ON time (low) 002Fh 00047
Holding Registers, “D” Group Monitor Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							SJ7002 Inverter
Appendix B
B–39
D084 — Trip monitor 4R Factor code0030h 00048 (see codes in 
next table)—
R Inverter status 0031h 00049—
R Frequency (high) 0032h 00050 0 to 40000 0.01 Hz
R Frequency (low) 0033h 00051
R Current 0034h 00052 — 0.1 A
R Voltage 0035h 00053 — 1 V
R Run time (high) 0036h 00054 — 1 hour
R Run time (low) 0037h 00055
R ON time (high) 0038h 00056 — 1 hour
R ON time (low) 0039h 00057
D085 — Trip monitor 5 R Factor code003Ah 00058 (see codes in 
next table)—
R Inverter status 003Bh 00059—
R Frequency (high) 003Ch 00060 0 to 40000 0.01 Hz
R Frequency (low) 003Dh 00061
R Current 003Eh 00062 — 0.1 A
R Voltage 003Fh 00063 — 1 V
R Run time (high) 0040h 00064 — 1 hour
R Run time (low) 0041h 00065
R ON time (high) 0042h 00066 — 1 hour
R ON time (low) 0043h 00067
D086 — Trip monitor 6 R Factor code0044h 00068 (see codes in 
next table)—
R Inverter status 0045h 00069—
R Frequency (high) 0046h 00070 0 to 40000 0.01 Hz
R Frequency (low) 0047h 00071
R Current 0048h 00072 — 0.1 A
R Voltage 0049h 00073 — 1 V
R Run time (high) 004Ah 00074 — 1 hour
R Run time (low) 004Bh 00075
R ON time (high) 004Ch 00076 — 1 hour
R ON time (low) 004Dh 00077
D090 — Programming error  monitor R Displays programming error 
code 004Eh 00078 Warning 
code—
— (Reserved) ——004Fh 
to 
08FFh 00079 
to 
02303 ——
Holding Registers, “D” Group Monitor Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							ModBus Data Listing
Appendix B
B–40
Note 1:Assume that the inverter current rating is 1000 (for D002).
Note 2: When the value is 10000 (100.0 seconds),  a value in the second decimal place is 
ignored.
— — Write to EEPROM W 00 . Motor constant calculation 01 .  Set data storage in 
EEPROM
Other... Motor constant recalcu-
lation and set data storage in 
EEPROM 0900h 02304 0000,
0001,
other —
— (Reserved) ——0901h 
to 
1000h 02305 
to 
4096 ——
D102 — DC voltage monitoring Displays the DC Bus voltage 1026h 04134 0 to 9999 0.1 V
D103 — BRD load factor monitor- ing Displays the running average 
Dynamic Braking usage ratio 
(%ED)1027h 04135 0 to 1000 0.1 %
D104 — Electronic thermal  overload monitoring Displays the motor electronic 
thermal overload estimated 
temperature ratio. If the value 
reaches 100%, th
e inverter will 
trip (E05) 1028h 04136 0 to 1000 0.1 %
— (Reserved) ——1029h 
to 
102Dh 04137 
to 
04141 ——
Holding Registers, “D” Group Monitor Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							SJ7002 Inverter
Appendix B
B–41
Trip Factor Code, HIGH orderTrip Factor Code, LOW order (inverter status)
CodeNameCodeName
0 No trip 0 Reset
1 Over current event while at constant  speed 1Stop
2 Over current event during  deceleration 2 Deceleration
3 Over current event during acceleration 3 Constant speed
4 Over current event during other condi- tions 4 Acceleration
5 Overload protection 5 Run Command active with 0 Hz speed  reference
6 Braking resistor  overload 6 Starting
7 Over voltage protection 7 DC braking
8 EEPROM error 8 Overload restriction
9 Under-voltage error 9 SON or FOC operation in progress
10 CT (current tr ansformer) error
11 CPU error
12 External trip
13 USP
14 Ground fault
15 Input over-voltage
16 Instantaneous power failure
20 Inverter thermal trip with low fan  speed
21 Inverter thermal trip
23 Gate array error
24 Phase failure detection
25 Main circuit error
30 IGBT error
35 Thermistor
36 Brake error
37 Emergency stop
38 Low-speed overload protection
43 Easy sequence erro r (invalid instruc-
tion)
44 Easy sequence erro r (invalid nesting 
count)
45 Easy sequence execution error 1
50 to 59 Easy sequence user trip 0 to 9
60 to 69 Expansion card #1 error 0 to 9
70 to 79 Expansion card #2 error 0 to 9

Phone: 800.894.0412   
						

							ModBus Data Listing
Appendix B
B–42
Holding Registers, “F” Group Main Profile Parameters
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.
F001 H Output frequency setting R/W Standard default target  frequency that deter-
mines constant motor 
speed (when A001 = 03)0001h 00001 0 to 40000 0.01 Hz
F001 L R/W 0002h 00002
F002 H Acceleration (1) time  setting R/W Standard default acceler-
ation 1103h 04355 1 to 
3600000.01 sec.
F002 L R/W 1104h 04356
F202 H Acceleration (1) time  setting, 2nd motor R/W Standard default acceler-
ation, 2nd motor 2103h 08451 1 to 
3600000.01 sec.
F202 L R/W 2104h 08452
F302 H Acceleration (1) time  setting, 3rd motor R/W Standard default acceler-
ation, 3rd motor 3103h 12547 1 to 
3600000.01 sec.
F302 L R/W 3104h 12548
F003 H Deceleration (1) time  setting R/W Standard default deceler-
ation 1105h 04357 1 to 
3600000.01 sec.
F003 L R/W 1106h 04358
F203 H Deceleration (1) time  setting, 2nd motor R/W Standard default deceler-
ation, 2nd motor 2105h 08453 1 to 
3600000.01 sec.
F203 L R/W 2106h 08454 — — (Reserved) — — 2107h  to 
2202h 08455 
to 
08706 ——
F303 H Deceleration (1) time  setting, 3rd motor R/W Standard default deceler-
ation, 3rd motor 3105h 12549 1 to 
3600000.01 sec.
F303 L R/W 3106h 12550 — — (Reserved) — — 3107h  to 
3202h 12551 
to 
12802 ——
F004 — Keypad Run key routing R/W 1107h 04359 — — (Reserved) — — 1108h  to 
1200h 04360 
to 
04608 ——

Phone: 800.894.0412   
						

							SJ7002 Inverter
Appendix B
B–43
       
Holding Registers, “A” Group  Standard Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.
A001 — Frequency source setting R/W 00 . Keypad potentiometer 01 . Control terminal
02 . Function F001 setting
03 . RS485 serial command
04 . Expansion board #1
05 . Expansion board #2
06 . Pulse train input
07 . Easy sequence
10 . Caltulate function input1201h 04609 00 to 07, 
10—
A002 — Run command source  setting R/W 01 . Input [FW] or [RV]
02 . Run key on keypad
03 . RS485 serial command
04 . Start/stop, Exp. card #1
05 . Start/stop. exp. card #2 1202h 04610 01 to 05 —
A003 — Base frequency setting R/W 30. to  max. frequency (Hz) 1203h 04611 30 to 
A004 val.1 Hz
A203 — Base frequency setting,  2nd motor R/W 30. to max. frequency (Hz) 2203h 08707 30 to 
A004 val.1 Hz
A303 — Base frequency setting, 3rd  motor R/W 30. to max. frequency (Hz) 3203h 12803 30 to 
A004 val.1 Hz
A004 — Maximum frequency  setting R/W 30. to 400. (Hz) 1204h 04612 30 to 400 1 Hz
A204 — Maximum frequency  setting, 2nd motor R/W 30. to 400. (Hz) 2204h 08708 30 to 400 1 Hz
— (Reserved) — — 2205h  to 
2215h 08709 
to 
08725 ——
A304 — Maximum frequency  setting, 3rd motor R/W 30. to 400. (Hz) 3204h 12804 30 to 400 1 Hz
— (Reserved) — — 3205h  to 
3215h 12805 
to 
12821 ——
A005 — [AT] selection R/W 00 . Select between [O] and       [OI] at [AT]
01 . Select between [O] and
      [O2] at [AT]
02 . Select between [O] and
      keypad pot.
03 . Select between [OI] and
      keypad pot.
04 . Select between [O2] and
      keypad pot.1205h 04613 00 to 04 —
A006 — [O2] selection R/W 00 . No summing, [O2] and       [OI]
01 . Sum of [O2] and [OI],
      neg. sum (reverse speed
      reference) inhibited
02 . Sum of [O2] and [OI],
      neg. sum (reverse speed
      reference) allowed
03 . Disable [O2] input1206h 046 00 to 03 —

Phone: 800.894.0412   
						

							ModBus Data Listing
Appendix B
B–44
— (Reserved)——1207h 
to 
120Ah 04614 
to 
04618 ——
A011 H [O]–[L] input active range  start frequency R/W The output frequency corre-
sponding to the voltage input 
range starting point 120Bh 04619 0 to 40000 0.01 Hz
A011 L 120Ch 04620
A012 H [O]–[L] input active range  end frequency R/W The output frequency corre-
sponding to the voltage input 
range ending point 120Dh 04621 0 to 40000 0.01 Hz
A012 L 120Eh 04622
A013 — [O]–[L] input active range  start voltage R/W The starting point for the 
voltage input range 120Fh 04623 0 to A014 
value1 %
A014 — [O]–[L] input active range  end voltage R/W The ending point for the 
voltage input range 1210h 04624 A013 
value to 100 1 %
A015 — [O]–[L] input start  frequency enable R/W 00 ..Use A011 start value
01 ..Use 0 Hz 1211h 04625 0, 1 —
A016 — External frequency filter  time const. R/W n = 1 to 30 (where n = 
number of samples for 
average); 31 = 500ms filter 1212h 04626 1 to 30, 31 1
A017 — Easy sequence function  enable R/W 00 ..Disable
01 ..Enable 1213h 04627 0, 1 —
— (Reserved) ——1214h 04628 — —
A019 — Multi-speed operation  selection R/W 00 ..Binary; up to 16-stage
      speed using 4 terminals
01 ..Single-bit; up to 8-stage
     speed using 7 terminals 1215h 04629 0, 1 —
A020 H Multi-spee d frequency 
setting R/W Defines the first speed of a 
multi-speed profile 1216h 04630 0 or start 
freq. to 
max. freq. 0.01 Hz
A020 L 1217h 04631
A220 H Multi-spee d frequency 
setting, 2nd motor R/W Defines the first speed of a 
multi-speed profile for 2nd 
motor 2216h 08726 0 or start 
freq. to 
max. freq. 0.01 Hz
A220 L 2217h 08727
— (Reserved) ——2218h 
to 
223Ah 08728 
to 
08762 ——
A320 H Multi-spee d frequency 
setting, 3rd motor R/W Defines the first speed of a 
multi-speed profile for 3rd 
motor 3216h 12822 0 or start 
freq. to 
max. freq. 0.01 Hz
A320 L 3217h 12823
— (Reserved) ——3218h 
to 
323Bh 12824 
to 
12859 ——
A021 H Multi-speed 1 setting R/W Def

ines nth additional speed 1218h 04632 0 or start 
freq. to 
max. freq. 0.01 Hz
A021 L 1219h 04633
A022 H Multi-speed 2 setting R/W Defines nth additional speed 121Ah 04634 0 or start 
freq. to 
max. freq. 0.01 Hz
A022 L 121Bh 04635
A023 H Multi-speed 3 setting R/W Defines nth additional speed 121Ch 04636 0 or start 
freq. to 
max. freq. 0.01 Hz
A023 L 121Dh 04637
Holding Registers, “A” Group  Standard Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							SJ7002 Inverter
Appendix B
B–45
A024 H Multi-speed 4 setting R/W Defines nth additional speed 121Eh 04638 0 or start freq. to 
max. freq. 0.01 Hz
A024 L 121Fh 04639
A025 H Multi-speed 5 setting R/W Defines nth additional speed 1220h 04640 0 or start  freq. to 
max. freq. 0.01 Hz
A025 L 1221h 04641
A026 H Multi-speed 6 setting R/W Defines nth additional speed 1222h 04642 0 or start  freq. to 
max. freq. 0.01 Hz
A026 L 1223h 04643
A027 H Multi-speed 7 setting R/W Defines nth additional speed 1224h 04644 0 or start  freq. to 
max. freq. 0.01 Hz
A027 L 1225h 04645
A028 H Multi-speed 8 setting R/W Defines nth additional speed 1226h 04646 0 or start  freq. to 
max. freq. 0.01 Hz
A028 L 1227h 04647
A029 H Multi-speed 9 setting R/W Defines nth additional speed 1228h 04648 0 or start  freq. to 
max. freq. 0.01 Hz
A029 L 1229h 04649
A030 H Multi-speed  10 setting R/W Defines nth additiona l speed 122Ah 04650 0 or start 
freq. to 
max. freq. 0.01 Hz
A030 L 122Bh 04651
A031 H Multi-speed  11 setting R/W Defines nth additiona l speed 122Ch 04652 0 or start 
freq. to 
max. freq. 0.01 Hz
A031 L 122Dh 04653
A032 H Multi-speed  12 setting R/W Defines nth additiona l speed 122Eh 04654 0 or start 
freq. to 
max. freq. 0.01 Hz
A032 L 122Fh 04655
A033 H Multi-speed  13 setting R/W Defines nth additiona l speed 1230h 04656 0 or start 
freq. to 
max. freq. 0.01 Hz
A033 L 1231h 04657
A034 H Multi-speed  14 setting R/W Defines nth additiona l speed 1232h 04658 0 or start 
freq. to 
max. freq. 0.01 Hz
A034 L 1233h 04659
A035 H Multi-speed  15 setting R/W Defines nth additiona l speed 1234h 04660 0 or start 
freq. to 
max. freq. 0.01 Hz
A035 L 1235h 04661
— (Reserved) — — 1236h 04662 — —
— (Reserved) — — 1237h 04663 — —
A038 — Jog frequency setting R/W De fines limited speed for jog1238h 04664 0 to 999 0.01 Hz
Holding Registers, “A” Group  Standard Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							ModBus Data Listing
Appendix B
B–46
A039 — Jog stop modeR/W 00 ..Free-run stop, jogging
      disabled during motor run
01 ..Controlled deceleration,
      jogging disabled during
      motor run
02 ..DC braking to stop,
      jogging  disabled during
      motor run
03 ..Free-run stop, jogging
      always enabled
04 ..Controlled deceleration,
      jogging always enabled
05 ..DC braking to stop,
      jogging  always enabled 1239h 04665 0 to 5 —
— (Reserved) ——123Ah 04666 — —
A041 — Torque boost method  selection R/W 00 ..Manual torque boost
01 ..Automatic torque boost 123Bh 04667 0, 1 —
A241 — Torque boost method  selection, 2nd motor R/W 00 ..Manual torque boost
01 ..Automatic torque boost 223Bh 08763 0, 1 —
A042 — Manual torque boost value R/W Can boost starting torque  between 0 and 20% above 
normal V/f curve123Ch 04668 0 to 200 0.1 %
A242 — Manual torque boost value,  2nd motor R/W Can boost starting torque 
between 0 and 20% above 
normal V/f curve 223Ch 08764 0 to 200 0.1 %
A342 — Manual torque boost value,  3rd motor R/W Can boost starting torque 
between 0 and 20% above 
normal V/f curve 323Ch 12860 0 to 200 0.1 %
A043 — Manual torque boost  frequency adjustment R/W Sets the frequency of the V/f 
breakpoint for torque boost 123Dh 04669 0 to 500 0.1 %
A243 — Manual torque boost  frequency adjustment, 2nd 
motor R/W Sets the frequency of the V/f 
breakpoint for torque boost 223Dh 08765 0 to 500 0.1 %
A343 — Manual torque boost  frequency adjustment, 3rd 
motor R/W Sets the frequency of the V/f 
breakpoint for torque boost 323Dh 12861 0 to 500 0.1 %
A044 — V/F characteristic curve  selection R/W 00 ..V/f constant torque
01 ..V/f variable torque
02 ..V/f free-setting curve
03 ..Sensorless vector SLV
04 ..0Hz domain SLV
05 ..Vector control with
       encoder feedback 123Eh 04670 0 to 5 —
A244 — V/F characteristic curve  selection, 2nd motor R/W 00 ..V/f constant torque
01 ..V/f variable torque
02 ..V/f free-setting curve
03 ..Sensorless vector SLV
04 ..0Hz domain SLV 223Eh 08766 0 to 4 —
— (Reserved) ——223Fh 08767 — —
A344 V/F characteristic curve  selection, 3rd motor R/W 00 ..V/f constant torque
01 ..V/f variable torque 323Eh 12862 0, 1 —
Holding Registers, “A” Group  Standard Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412   
						

							SJ7002 Inverter
Appendix B
B–47
— (Reserved)——323Fh 
to 
326Ch 12863 
to 
12908 ——
A045 — V/f gain setting R/W Sets voltage gain of the 
inverter 123Fh 04671 20 to 200 1 %
A046 — Automatic torque boost  voltage gain R/W Voltage compensation gain 
for automatic  torque boost 1240h 04672 0 to 255 1
A246 — Automatic torque boost  voltage gain, 2nd motor R/W Voltage compensation gain 
for automatic  torque boost 2240h 08768 0 to 255 1
A047 — Automatic torque boost  slip gain R/W Slip compensa
tion gain for 
automatic to rque boost 1241h 04673 0 to 255 1
— (Reserved) ——1242h 
to 
1244h 04674 
to 
04676 ——
A247 — Automatic torque boost  slip gain, 2nd motor Slip compensa
tion gain for 
automatic to rque boost 2241h 08769 0 to 255 1
— (Reserved) ——2242h 
to 
224Eh 08770 
to 
08782 ——
A051 — DC braking enable R/W 00 . Disable 01 . Enable
02 . Brake at set frequency
      only1245h 04677 0, 1, 2 —
A052 — DC braking frequency  setting R/W Frequency at which DC 
braking activates during 
decel. 1246h 04678 0 to 40000 0.01 Hz
A053 — DC braking wait time R/W Th e delay after reaching the 
DC braking frequency, or 
[DB] signal, before DC 
braking begins 1247h 04679 0 to 50 0.1 sec.
A054 — DC braking force during  deceleration R/W Variable DC braking force 1248h 04680 0 to 80 1 %
A055 — DC braking  time for decel-
eration R/W Sets the duration for DC 
braking during decel 1249h 04681 0 to 600 0.1 sec.
A056 — DC braking / edge or level  detection for [DB] input R/W 00 . Edge detection
01 . Level detection 124Ah 04682 0, 1 —
A057 — DC braking force for  starting R/W Variable DC braking force 124Bh 04683 0 to 80 1 %
A058 — DC braking time for  starting R/W Sets the duration for DC 
braking before accel. 124Ch 04684 0 to 600 0.1 sec.
A059 — DC braking carrier  frequency setting R/W 0.5 to 15 (kHz) for models 
up to –550xxx, 0.5 to 10 
(kHz) for 750xxx to 1500xxx 
models 124Dh 04685 5 to 150;
5 to 1000.1 kHz
— (Reserved) ——124Eh 04686 — —
A061 H Frequency upper limit  setting R/W Sets a limit on output 
frequency less than the 
maximum frequency (A004) 124
Fh 0468 7
 0, 50 to 
40000 0.01 Hz
A061 L 1250h 04688
Holding Registers, “A” Group  Standard Functions
Func. CodeNameR/WDescription
Network Data
RegisterRangeRes.hexdec.

Phone: 800.894.0412