Home > Epson > Printer > Epson C 2900 Manual

Epson C 2900 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson C 2900 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 681
    							6 - 54 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    5.5 Fuser Unit Control
    5.5.1 Fuser Unit temperature control
    As for the Fuser Unit temperature control, the target temperature is set, then the Heat Roll surface tem-
    perature is controlled so that it can meet the target value by turning on/off the Heater Lamp.
    Temperature of individual area of the Heat Roll is detected by the Fuser Unit Non-Contact Sensor 
    (NCS) in the middle of the Heat Roll and the Temp Sensor at the edge of it. When the temperature 
    detected is higher than the target value, the Heater Lamp will be turned OFF. When the temperature is 
    below the target value, the Heater Lamp will be turned ON.
    The target temperature setting varies depending on the time of Warm-up, Printing, or Process Control. 
    The target temperature varies according to such environmental factors as the interior temperature 
    detected by the Sensor Hum Temp.
    5.5.2 Cooling down
    As the printing continues, the temperature distribution in the Heat Roll becomes uneven both in the 
    paper feed and non-paper feed areas. Cooling Down suspends paper feeling for a certain period of 
    time so that the Heat Roll temperature distribution can be uniform. 
    When the temperature of the Heat Roll edge is high, cooling down is performed to lower the tempera-
    ture to the target value.
    5.5.3 Sensor Warm-up
    The Fuser Unit NCS (Non Contact Sensor) at the center of the Heat Roll will be lose its accuracy of 
    detecting temperature when the temperature of the Sensor itself is below -5°C. Therefore, the Sensor 
    will be warmed up when the temperature is below -5°C. This action is called Sensor Warm-up. 
    						
    							6 - 55 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    6. Drive Transmission Route
    6.1 DRIVE ASSY MAIN
    Rotation power of the DRIVE ASSY MAIN is transmitted through the route below.
    DRIVE ASSY  MAIN
    [ BELT ]
    TRANSFER ASSY
    [ Name of moving parts ]
    GEAR P3
    DRIVE ASSY  PH
    CHUTE ASSY FDR REGI
    CLUTCH ASSY  DRV
    GEAR REGI RUBBER
    GEAR REGI METAL
    GEAR P2GEAR T4
    GEAR P4
    GEAR P5
    [ ROLL ASSY REGI ]
    [ ROLL REGI METAL ]
    GEAR ASSY  FEEDSOLENOID FEED MSIGEAR DRV
    [ ROLL ASSY FEED ]
    HSG ASSY XERO (K)[ DRUM (K) ]HSG ASSY XERO (C)[ DRUM (C) ]
    GEAR PHD 2
    HSG ASSY XERO (M)[ DRUM (M) ]
    HSG ASSY XERO (Y)[ DRUM (Y) ]
    GEAR PHD 2
    GEAR PHD 1
    Drum Cartridge
    MiS06032KA [ PAPER FEED DRIVE ] / [ DRUM and BELT DRIVE ] 
    						
    							6 - 56 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    FRONT
    MiS06033KA
    :  Indicates the engagement of gears.[ Name of moving parts ] [ PAPER FEED DRIVE ]
    DRIVE ASSY  PHDRIVE ASSY  MAIN
    GEAR P2
    GEAR P3 GEAR P4
    GEAR P5
    GEAR ASSY  FEEDCLUTCH ASSY
    DRVGEAR REGI RUBBER
    GEAR REGI METAL
    SOLENOID FEED MSI
    [ ROLL ASSY FEED ] [ ROLL ASSY REGI ]
    [ ROLL REGI METAL ] 
    						
    							6 - 57 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    FRONT
    MiS06034KA
    :  Indicates the engagement of gears.[ Name of moving parts ] [ DRUM and BELT DRIVE ]
    Drum Cartridge
    DRIVE ASSY  MAIN
    GEAR PHD 2 GEAR PHD 1 GEAR PHD 2
    GEAR T4GEAR DRV
    [ BELT ]
    [ DRUM (M) ]
    [ DRUM (Y) ]
    [ DRUM (K) ]
    [ DRUM (C) ] 
    						
    							6 - 58 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    6.2 DRIVE ASSY MAIN and DRIVE ASSY SUB DRIVE
    Rotation power of the DRIVE ASSY MAIN and DRIVE ASSY SUB are transmitted through the route 
    below.
    GEAR D1
    GEAR D2GEAR DK
    GEAR D1GEAR P2
    DRIVE ASSY  MAINSUB MOTOR
    GEAR D5
    GEAR MAG (K)GEAR D3 IN DRIVE ASSY  SUB
    GEAR D3 OUTFLANGE D3
    CAM C
    GEAR C
    GEAR P4-2GEAR P4
    GEAR P3
    COLOR MODE
    SWITCHING SOLENOID
    DRIVE ASSY  PH
    HSG ASSY DEVE (K) [ MAGNET ROLL (K) ]
    Drum Cartridge
    MiS06035KA
    [ Name of moving parts ][ BLACK and WHITE MODE ] 
    						
    							6 - 59 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    FRONT
    MiS06036KA GEAR MAG (K) [ MAGNET ROLL (K) ]GEAR D5
    GEAR D1 GEAR DK
    SUB MOTOR
    GEAR D1
    GEAR D2 DRIVE ASSY  SUB
    DRIVE ASSY  MAINDRIVE ASSY  PH
    DRIVE ASSY  PH
    GEAR P2
    GEAR P3
    COLOR MODE
    SWITCHING SOLENOID GEAR P4
    GEAR CCAM C FLANGE D3
    GEAR P4-2
    :  Indicates the engagement of gears.[ Name of moving parts ] [ BLACK and WHITE MODE ]
    GEAR D2 FLANGE D3 CAM C
    GEAR D4
    GEAR D3 IN GEAR D3 OUT 
    						
    							6 - 60 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential (Refer to 6.1 PHOTOCONDUCTOR (PC)/DEVELOPER (DEV) DRIVE [SIMPLEX MODE]
    DRIVE ASSY  MAINDRIVE ASSY  SUB
    GEAR PHD 1
    HSG ASSY XERO (Y, M, C, K)[ DRUM ]
    GEAR PHD 2
    GEAR AUGER  CLNGGEAR MAG IDLR
    GEAR IDLER PADDLE
    GEAR PADDLE
    GEAR AUGER
    GEAR AUGER
    GEAR IDLER AUGER SIDE
    GEAR AUGER  SIDE
    [ AUGER CLNG SIDE ]
    [ PADDLE DEVE ]
    [ AUGER FRONT ]
    [ AUGER REAR ]
    [ AUGER ]
    HSG ASSY DEVE (Y, M, C, K) [ MAGNET ROLL ]
    GEAR MAG (Y, M, C, K)[ Name of moving parts ]
    [ DEVELOPMENT and EXCESS TONER COLLECTING ]
    Drum Cartridge
    MiS06037KA 
    						
    							6 - 61 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    FRONT
    MiS06038KA
    :  Indicates the engagement of gears.[ Name of moving parts ] [ EXCESS TONER COLLECTING DRIVE ]
    [ DRUM ] GEAR AUGER  CLNG
    GEAR IDLER AUGER SIDEGEAR AUGER  SIDE
    DRIVE ASSY  MAIN
    GEAR PHD 2 GEAR PHD 1 GEAR PHD 2
    Drum Cartridge
    [ AUGER CLNG SIDE ]
    [ AUGER ]
    HSG ASSY  XERO 
    						
    							6 - 62 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    FRONT
    MiS06039KA
    :  Indicates the engagement of gears.[ Name of moving parts ] [ DEVELOPMENT DRIVE ]
    DRIVE ASSY  SUB
    Drum Cartridge
    GEAR MAGGEAR MAG IDLR GEAR IDLER PADDLE
    GEAR PADDLE
    GEAR AUGER GEAR AUGER HSG ASSY  DEVE
    [ MAGNET ROLL ]
    [ AUGER REAR ]
    [ AUGER FRONT ]
    [ PADDLE DEVE ] 
    						
    							6 - 63 Chapter 6   Principles of Operation
    Epson AcuLaser C2900NRevision B
    Confidential
    6.3 TONER DISPENSER (Y, M, C, K)
    Rotation power of the TONER DISPENSER drives the agitator and the auger in the TONER CAR-
    TRIDGE.
    [TONER CARTRIDGE]
    [ Name of moving parts ]
    DISPENSER ASSY
    TONER CARTRIDGE (K)
    GEAR IDLER (K)
    MOTOR ASSY DISP (K)
    GEAR AGITATOR  (K)
    [ TONER DISPENSER ]
    [ AUGER (K) ]
    GEAR IDLER AGI (K)
    GEAR IDLER AUG (K)
    [ AGITATOR (K) ]
    TONER CARTRIDGE (C)
    GEAR AGITATOR  (C)
    [ AGITATOR (C) ]
    TONER CARTRIDGE (M)
    GEAR AGITATOR  (M)
    [ AGITATOR (M) ]
    TONER CARTRIDGE (Y)
    GEAR AGITATOR  (Y)
    [ AGITATOR (Y) ]
    GEAR AUGER  (K)
    GEAR IDLER (C)
    MOTOR ASSY DISP (C)
    [ AUGER (C) ]
    GEAR IDLER AGI (C)
    GEAR IDLER AUG (C)
    GEAR AUGER  (C)
    GEAR IDLER (M)
    MOTOR ASSY DISP (M)
    [ AUGER (M) ]
    GEAR IDLER AGI (M)
    GEAR IDLER AUG (M)
    GEAR AUGER  (M)
    GEAR IDLER (Y)
    MOTOR ASSY DISP (Y)
    [ AUGER (Y) ]
    GEAR IDLER AGI (Y)
    GEAR IDLER AUG (Y)
    GEAR AUGER  (Y)
    MiS06040KA 
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson C 2900 Manual